- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
PPG Nu-Klad SL is a three-component, solvent-free, self-levelling epoxy floor coating available in 400+ colours and shades from RAL and British Standard.
- Suitable for industrial areas with heavy traffic
- Excellent abrasion resistance
- Excellent resistance againts hot tires
- Suitable for use with anti-skid
- Shelf life:
- Base & Hardener - minimum 12 months
- Filler - minimum 36 months
Product customisation
Don't forget to save your customization to be able to add to cartQuick Links - Click To Jump To Section:
- Recommended Substrate Conditions & Temperatures
- System Specification
- Instructions for Use
- Safety Precautions
Recommended Substrate Conditions & Temperatures
Primed concrete:
- Suitable primer must be dry and free from any contamination
Coated concrete:
- Existing sound coating systems; sufficiently roughened, dry and cleaned
- To ensure compatibility, rub the existing coating with a cloth with Xylene or MEK for 10 seconds, and remove existing coatings if dissolving occurs
- Rough surface; eventually abraded by power tool or diamond abrading tool
Substrate temperature and application conditions:
- Ambient temperature during application and curing should be between 10°C and 25°C
- Relative humidity during application and curing should not exceed 85%
- Substrate temperature during application and curing should be between 10°C and 30°C
- Substrate temperature during application should be at least 5°C above dew point
System Specification
Standard system:
- NU-KLAD SL: 1 x 2000 µm (80.0 mils) on top of primed concrete
Fully sprinkled anti-skid system:
- NU-KLAD SL: 1 x 2000 µm (80.0 mils) on top of primed concrete
- Anti-skid fully sprinkled
- Note: In case of fully sprinkled an extra layer of SIGMADUR 520 or SIGMADUR 550 can be applied for a better aesthetical appearance
Instructions for Use
Mixing ratio by weight: base to hardener to filler 14:3.1:7.9:
- Material temperature should be between 10°C and 20°C
- Mix base and hardener with a variable-speed mechanical mixer thoroughly for 1 minute
- Add the filler while stirring and stir thoroughly for 2 minutes
- Pour the mixture into another can and mix for 2 minutes, until homogeneous
- The speed of the mixer should not exceed 800 rpm to avoid air entrapment
Induction time:
- None
Pot life:
- 35 minutes at 10°C
- 25 minutes at 20°C
- 15 minutes at 25°C
Anti-skid system:
- Apply NU-KLAD SL: 1 x 2000 μm on top of primed concrete
- Fully sprinkle anti-skid in the wet layer
- Remove excess of anti-skid after drying
- An extra layer of 50 μm SIGMADUR 520 or SIGMADUR 550 can be applied for a better aesthetical appearance
Trowel/Swedish knife:
- Pour an appropriate amount of mixture on the primed concrete and spread it evenly by trowel or Swedish knife
- Use a spiked roller to avoid air entrapment
Recommended thinner:
- No thinner should be added
Cleaning solvent:
Overcoating interval for DFT up to 2000 µm (80.0 mils):
- Nu-Klad SL:
- 24 hours - 7 days @ 20°C
- Polyurethane topcoat:
- 36 hours - 3 days @ 20°C
- Surface should be dry and free from any contamination
- For intervals exceeding the maximum overcoating interval, the surface has to be roughened sufficiently before overcoating
Curing time for DFT up to 2000 µm (80.0 mils):
- Dry to walk on: 24 hours @ 20°C
- Light impact/abrasion: 24 hours @ 20°C
- Full cure: 7 days @ 20°C
Safety Precautions
- Since improper use and handling can be hazardous to health and cause of fire or explosion, safety precautions included with Product Data/Application Instruction and Material Safety Data Sheets must be observed during all storage, handling, use and drying periods (see 'Data Sheets' section above)
Data sheet
- Manufacturer
- PPG
- For Use By
- Professional Use
- For Use On
- Industrial Floors
Concrete Floors - Application Method
- Spray
Trowel
Spiked Roller - Sheen
- Gloss
- Single, Two or Three Pack
- Three-Pack
- Solids by Volume
- 100%
- VOC
- UK PG 6/23(92) Appendix 3: max. 0.0 g/L
- Touch Dry
- 24 hours
- Recommended Dry Film Thickness
- 2000 µm (80.0 mils)
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Industrial Floors
- Finish
- Gloss
- Application Method
- Roller
- Application Method
- Spray
- Application Method
- Trowel
- Application Method
- Spiked Roller
- Manufacturer
- PPG
- Product Usage Type
- Floor Coating
- Product Range
- Nu-Klad
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Spreading Rate
- Approx. 3.3 kg/m² for 2000 µm (0.06 lb/ft² for 80 mils)
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
PPG Nu-Klad SL is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT