I'm looking for something i can easily apply to a fresh new concrete floor in a 1k sqft industrial unit. I will be using the unit for food production so I need something that will satisfy food hygiene rules (thay are very vague!). I also need a product that can be applied with ease because I have a neurodiverse disability so easy to understand instructions or help from customer services or a local rep might be useful if available. Thanks.

This product wouldn't be the best option as the aggregate present is angular, it would be more difficult to clean. Assuming the concrete floor is a minimum of 21 days old and/or the residual moisture content shall be below 6%, the concrete is bare, ground, clean, dry, sound and prepared as detailed in the technical data sheet you could consider 503 Easy Clean Anti-Slip Coating as an alternative. This product is suitable for use in food production and preparation areas, but please note it is not tested or certified as food safe. This can be mixed to many RAL, BS & NCS Colours and available to a textured gloss finish.

Looking at the 502 it's a 3-coat system with drying time of 6 hrs to touch. Would this be each coat after application? This will be applied on to an unprepared steel floor. I understand the better prep the better adhesion. Look forward to your response.

No this is not a 3 coat system it is a 3 pack product designed for professional use only. This should not be applied to unprepared steel, we would recommend the steel is blasted to SA2.5 prior to application, if blasting is not practical mechanical preparation can be used but this may shorten the life span of the coating.

Can this product be used on a workshop floor? we will be driving trucks in and out of our workshop

Absolutely, assuming the floor is concrete the product would be ideally suited to this type of application.

I am going to be using 502 HD Anti-Slip coating to provide a non-slip coating to metal pedestrian ramps. The existing metal ramps can become slippery when wet / icy, and the 502 seems to be the ideal product. The steel ramps are located outside, in isolated rural locations, and will only ever be used by foot traffic. Could you tell me what life expectancy I can expect from this product under these circumstances (can't find it within your web-site pages). Many thanks

The surface preparation will be key to longevity; the steel should ideally be shot blasted to produce a clean profile to optimise adhesion. Reduced levels of preparation may affect the bond strength and therefore the service-life; the use of a suitable primer, such as 404 Epoxy Metal Primer should also be considered on more minimally prepared surfaces. Given proper preparation, we would anticipate a minimum service life of 5 – 7 years for the system. 502 HD Anti Slip Coating is not UV stable so if colour/gloss retention/stability is important 309 Polyurethane Coating could be used, following a minimum 24 hours cure of the 502 HD.

Can you please advise of VOC content of your 502 HD anti-slip floor coating

502 HD Anti Slip Coating is VOC free.

Hello We are looking for something anti sip that can be used on a tiled surface. It is an external ramp entrance open to the elements. So needs to be weatherproof, anti-slip and needs to adhere to a tiled surface? Thanks

We would recommend after preparation, priming the tiles with Smartkote Protectakote Clear Primer Treatment and then finishing with Smartkote Protectakote UVR .

we are looking for a non slip concrete covering for use in our pool room in our canine hydrotherapy centre. The product must be waterproof as obviously some parts are permanently wet and inside a shower area also. It must be non slip and scratch resistance. Plus it needs to look nice too. Do you have a product you can recommend ?

Both our 502 HD Anti Slip Coating and 503 Easy Clean Anti Slip Coating would be suitable for this application. 502 leaves a much coarser more aggressive anti-slip profile than the 503.

can you apply over a previous painted floor

502 HD Anti Slip Coating should ideally be applied to bare or suitably primed floors. If an existing coating cannot be removed for any reason, then 502 HD Anti Slip Coating may be applied if the existing paints are epoxy based. Abrade the existing paint thoroughly to provide a key, ensure that any loose and flaking material is completely removed and test adhesion and compatibility by applying to a small area before proceeding. Alternatively, our 501 Anti Slip Floor Paint can be applied over most existing floor paints without issue.

Do you need a primer applied to the concrete floor before you use 502 HD Anti Slip Coating? If so what one should you use?

No primer is necessary if the concrete is clean, dry and prepared according to the data sheet. You can use 402 Damp Proof Coating if the concrete has no DPM (damp proof membrane), has a high moisture content or has recently been laid. You can use 403 Oil Tolerant Primer if the concrete has oil contamination.

502 HD Anti Slip Coating

Reference RAW502

Brand Rawlins Paints

Search ID RAW1104

A 3-pack solvent-free high-build epoxy resin system in 10 colours for application as a heavy duty non-slip floor coating for concrete, metal and wood surfaces requiring high levels of slip resistance.

Ideal for use in high traffic areas requiring high slip resistance such floors, stairs, ramps, loading bays
Also suitable for chemical plant rooms, engineering workshops, automotive and aviation areas, factory units and warehouses
Excellent for all demarcation and walkways
Also available in 4,000+ colours- 502 HD Anti Slip Coating - Special Colours
This product is for Professional Use Only
Images are for illustrative purposes only and may differ from the actual product

Product customisation

Don't forget to save your customization to be able to add to cart

Colour Group

Size

Finish

£107.34(incl. VAT)

£89.45(ex. VAT)

Quantity

Please choose your colour

Available for Delivery (See Delivery Options Below)

ColourPicker Explained

In general we sort colours for products into 2 main groups - ‘Ready Mixed’ and ‘Tinted’.
Tinted colours will always be more expensive than Ready Mixed colours as they need to be produced at the time of order using a tinting machine dispensing colourant into a base*.
During busy periods, this means that tinted colours could take longer, for example – a ready mixed colour ordered on a 3-5 day delivery might arrive within 3 days, however a tinted colour might take the full 5 days to arrive.

To find Ready Mixed colours, search "ready mixed" or select the Ready Mixed 'colour chart'. To see Tinted colours select a colour chart such as RAL, BS, NCS, etc. or search for a colour/hue to see available or related options.

To ensure fair pricing, we split colours into ‘Price Bands’ to group together similar priced colours. If you wish to search for the cheapest tinted colours, always select Price Band 1.

We make every effort to list all available colours, however we also offer a colour match service which can be accessed by contacting our Technical Team on 0113 245 5450 (option 2) or emailing [email protected]

*Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour

Colour reproduction of the Products on the Site is limited by the technology used to deliver web pages and by the colour representation of Customer’s own monitor and computer set-up. We have made every effort to display as accurately as possible the colours of our Products but we cannot guarantee that the colour shown on Customer’s monitor’s display will accurately reflect the colour of the Product on delivery. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person (and not digitally) to ensure that the colour is acceptable for its purposes.

9 questions about the product

Description

502 HD Anti Slip Coating is applied by brush or roller in one thick, durable coat and each composite pack contains sufficient material to provide a slip resistant epoxy coating system to 5 square metres of surface. Solvent and virtually odour free, 502 HD Anti Slip Coating is finished with a hard wearing aluminium oxide anti-slip aggregate and will withstand heavy traffic including fork lift trucks and chemicals.

502 HD Anti Slip Coating is a 3-pack solvent-free high-build epoxy resin system for application as a heavy duty non-slip floor coating for concrete, metal and wood surfaces requiring high levels of slip resistance.

502 HD Anti Slip Coating will provide a heavily textured coloured finish incorporating an anti-slip aggregate which is dispersed within the material upon application.

This product is for Professional Use Only.

Recommended Uses:

High traffic areas requiring high slip resistance such floors, stairs, ramps, loading bays, etc
Chemical plant rooms
Engineering workshops
Automotive and aviation areas
Factory units
Warehouses
Excellent for all demarcation and walkways

Features & Benefits

Coverage 5m² per pack
Solvent free and virtually odourless
Withstands heavy traffic including fork lift trucks
Three-pack
For concrete, metal and wood surfaces
Easy to apply and good colour stability
Excellent slip resistance
Hygienic and good chemical resistance
Tough, long lasting high-build finish

Typical Properties

Technical Data
	502 HD Anti Slip Coating
Pot life @ 20°C:	30 Minutes
Tack Free Time @20°C:	3 hours
Hard Dry Time @ 20°C:	6 hours
Full Chemical Resistance @20°C:	7 days
Adhesive strength to Concrete:	3.7MPd (concrete failure)
Mohs Hardness of Aggregate:	9

Chemical Resistance
Chemical	Resistance
Dilute Acids and Alkalis	Excellent
Oil	Excellent
Petrol	Excellent
Diesel	Excellent
Inorganic Salts	Excellent

Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.

Coverage

5m² per pack

Surface Preparation

Concrete:

Concrete surfaces shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes etc
Smooth concrete, or concrete with soft laitance, shall be mechanically treated by diamond grinding or grit blasting to provide a clean profiled surface
Should this not be practicable then acid etching, although less preferable, is also an option

Metal:

Metal surfaces shall be wire brushed or power disced to remove any rust and loose or flaking material
Grit blasting is recommended, where practical, for optimum performance
Coating application should be carried out immediately after preparation

Wood:

Wood surfaces shall be sanded to a smooth finish, and all previous coating removed
Do not add the aggregate into the mix

Note: Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers. Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full detail.

Mixing:

Pre-mix the coloured base component to a uniform consistency then mix the entire contents of the base with the hardener using a slow speed electric mixer for approximately two minutes or until the two components have fully combined
Pour the contents of the curing agent container into the base container and thoroughly mix, preferably by mechanical means until a uniform consistency is achieved

Note: If a separate mixing bucket is being used then mix thoroughly as above ensuring all contents of the 2 components are removed from the buckets supplied

Mixing Ratio:

By Volume - 2.56 Base : 1 Curing Agent
By Weight - 100 Base : 26.9 Curing Agent

Application

The ambient temperatures of the areas should not be allowed to fall below 10°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system
Surface temperature must be above 5°C
Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation
The mixed unit should be applied immediately by medium pile roller (not foam) or brush with a consistent procedure at an even rate of application to a measured area of no more than 5m² per pack
Floor areas should be cross-rolled to ensure even application and to minimise roller marks
Immediately scatter the anti-slip aggregate uniformly onto the wet coat to obtain the desired surface finish (total or light coverage as required)
Using the same roller that was used to apply the mixed resin and hardener roll over the sprinkled aggregate to bed in and cover the anti-slip aggregate
It is not normally necessary to re-charge the roller with mixed resin unless very heavy quantities of grit have been applied
Coverage rates will depend on profile and porosity of the substrate
304 HD Epoxy Floor Coating can be installed as a first coat for a smooth finish followed by a top coat of 502 HD Anti Slip Coating for a textured finish
Or an additional coat of 304 HD Epoxy Floor Coating can be applied (not exceeding 200 microns) over the cured 502 HD Anti Slip Coating system to increase the life expectancy of the system and make the finished surface easier to clean (please note this will most likely reduce the level of slip resistance)

Cleaning

It is impracticable to clean rollers after use
Clean equipment with 109 Tool Cleaner prior to curing of the coating

Curing

Allow to cure for a minimum of 8 hours @ 20°C prior to light foot traffic access
Curing at lower temperatures will extend this period, whereas curing at higher temperatures will allow faster access

Limitations

Do not apply to wet or uncured concrete surfaces
Do not apply at temperatures of 3°C or less

Storage & Shelf Life

Store in dry conditions at temperatures between 10°C and 25°C
Do not expose to freezing conditions
502 HD Anti Slip Coating has a minimum of 12 months shelf life when stored in original, unopened containers in accordance with manufacturer’s instructions

Health & Safety

Wear gloves and goggles
Wash off splashes immediately with soap and water
Please refer to Material Safety Data Sheet for additional information
502 HD Anti Slip Coating shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]

Product Details

Reference 1104-862932

Data sheet

For Use By: Professional Use
Interior / Exterior Use: Interior & Exterior
Water / Solvent Based: Water
For Use On: Concrete, Wood, Metal
Application Method: Brush, Roller
Single, Two or Three Pack: Three-Pack
Pack Size: 5m²
Mixing Ratio: 2.56 Base : 1 Curing Agent
Fully Cured (at 20°C): 7 Days
Pot Life (at 20°C): 30 Minutes
Min. Application Temperature: 10°C
Shelf Life (from date of manufacture): 12 Months
Touch Dry: 3 Hours
UN Number: UN3082
Base Type: Solvent-Free
Suitable For Use On: Aviation Areas
Suitable For Use On: Timber
Suitable For Use On: Factory Units
Suitable For Use On: Metal
Suitable For Use On: Workshop Floors
Suitable For Use On: Concrete
Suitable For Use On: Demarcation
Suitable For Use On: Wood
Suitable For Use On: Aircraft Hangers
Suitable For Use On: Floors
Suitable For Use On: Warehouse Floors
Suitable For Use On: Loading Bays
Suitable For Use On: Stairs
Suitable For Use On: Walkways
Suitable For Use On: Ramps
Suitable For Use On: Warehouses
Suitable For Use On: Workshops
Suitable For Use On: Chemical Plant Rooms
Suitable For Use On: Engineering Workshops
Suitable For Use On: Automotive Areas
Finish: Textured Gloss
Application Method: Brush
Application Method: Roller
Components: 3K
Usages: Anti-Slip
Product Usage Type: Topcoat
Product Category: Paints
Colour Family: Yellow
Colour Family: Black
Colour Family: White
Colour Family: Grey
Colour Family: Green
Colour Family: Blue
Colour Family: Red
Anti-Slip Texture: Coarse Texture
Product Type: Epoxy

Attachments

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

Name ^*

Email ^*

Question ^*

^* Required fields

I have read and agree to the conditions of use (read)

Stuart C. on 2023-08-11 22:30:54	Question: I'm looking for something i can easily apply to a fresh new concrete floor in a 1k sqft industrial unit. I will be using the unit for food production so I need something that will satisfy food hygiene rules (thay are very vague!). I also need a product that can be applied with ease because I have a neurodiverse disability so easy to understand instructions or help from customer services or a local rep might be useful if available. Thanks.
	Answer from Rawlins’ Technical Team: This product wouldn't be the best option as the aggregate present is angular, it would be more difficult to clean. Assuming the concrete floor is a minimum of 21 days old and/or the residual moisture content shall be below 6%, the concrete is bare, ground, clean, dry, sound and prepared as detailed in the technical data sheet you could consider 503 Easy Clean Anti-Slip Coating as an alternative. This product is suitable for use in food production and preparation areas, but please note it is not tested or certified as food safe. This can be mixed to many RAL, BS & NCS Colours and available to a textured gloss finish.

Paul on 2022-10-06 14:00:44	Question: Looking at the 502 it's a 3-coat system with drying time of 6 hrs to touch. Would this be each coat after application? This will be applied on to an unprepared steel floor. I understand the better prep the better adhesion. Look forward to your response.
	Answer from Rawlins’ Technical Team: No this is not a 3 coat system it is a 3 pack product designed for professional use only. This should not be applied to unprepared steel, we would recommend the steel is blasted to SA2.5 prior to application, if blasting is not practical mechanical preparation can be used but this may shorten the life span of the coating.

Michael Barr on 2019-12-23 11:40:25	Question: Can this product be used on a workshop floor? we will be driving trucks in and out of our workshop
	Answer from Rawlins’ Technical Team: Absolutely, assuming the floor is concrete the product would be ideally suited to this type of application.

Dale Smith on 2018-05-08 15:36:42	Question: I am going to be using 502 HD Anti-Slip coating to provide a non-slip coating to metal pedestrian ramps. The existing metal ramps can become slippery when wet / icy, and the 502 seems to be the ideal product. The steel ramps are located outside, in isolated rural locations, and will only ever be used by foot traffic. Could you tell me what life expectancy I can expect from this product under these circumstances (can't find it within your web-site pages). Many thanks
	Answer from Rawlins’ Technical Team: The surface preparation will be key to longevity; the steel should ideally be shot blasted to produce a clean profile to optimise adhesion. Reduced levels of preparation may affect the bond strength and therefore the service-life; the use of a suitable primer, such as 404 Epoxy Metal Primer should also be considered on more minimally prepared surfaces. Given proper preparation, we would anticipate a minimum service life of 5 – 7 years for the system. 502 HD Anti Slip Coating is not UV stable so if colour/gloss retention/stability is important 309 Polyurethane Coating could be used, following a minimum 24 hours cure of the 502 HD.

David Beecham on 2018-01-31 14:54:12	Question: Can you please advise of VOC content of your 502 HD anti-slip floor coating
	Answer from Rawlins’ Technical Team: 502 HD Anti Slip Coating is VOC free.

Ella on 2018-01-12 14:18:41	Question: Hello We are looking for something anti sip that can be used on a tiled surface. It is an external ramp entrance open to the elements. So needs to be weatherproof, anti-slip and needs to adhere to a tiled surface? Thanks
	Answer from Rawlins’ Technical Team: We would recommend after preparation, priming the tiles with Smartkote Protectakote Clear Primer Treatment and then finishing with Smartkote Protectakote UVR.

Helen Edis on 2017-05-25 04:57:54	Question: we are looking for a non slip concrete covering for use in our pool room in our canine hydrotherapy centre. The product must be waterproof as obviously some parts are permanently wet and inside a shower area also. It must be non slip and scratch resistance. Plus it needs to look nice too. Do you have a product you can recommend ?
	Answer from Rawlins’ Technical Team: Both our 502 HD Anti Slip Coating and 503 Easy Clean Anti Slip Coating would be suitable for this application. 502 leaves a much coarser more aggressive anti-slip profile than the 503.

jim wark on 2016-05-09 15:18:34	Question: can you apply over a previous painted floor
	Answer from Rawlins’ Technical Team: 502 HD Anti Slip Coating should ideally be applied to bare or suitably primed floors. If an existing coating cannot be removed for any reason, then 502 HD Anti Slip Coating may be applied if the existing paints are epoxy based. Abrade the existing paint thoroughly to provide a key, ensure that any loose and flaking material is completely removed and test adhesion and compatibility by applying to a small area before proceeding. Alternatively, our 501 Anti Slip Floor Paint can be applied over most existing floor paints without issue.

John Ward on 2016-02-06 07:34:57	Question: Do you need a primer applied to the concrete floor before you use 502 HD Anti Slip Coating? If so what one should you use?
	Answer from Rawlins’ Technical Team: No primer is necessary if the concrete is clean, dry and prepared according to the data sheet. You can use 402 Damp Proof Coating if the concrete has no DPM (damp proof membrane), has a high moisture content or has recently been laid. You can use 403 Oil Tolerant Primer if the concrete has oil contamination.

IMPORTANT SHIPPING & DELIVERY INFORMATION

502 HD Anti Slip Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

403 Oil Tolerant Primer

Developed for use in applications to oil contaminated floors prior to application of subsequent floor toppings. The product exhibits outstanding adhesion to concrete and other substrates and is particularly suitable where compromised surfaces exist. Solvent free, low odour Excellent adhesion to concrete and steel Surface tolerant...

£132.66 (incl. VAT)

Shop now

In Stock and Available for Delivery

304 HD Epoxy Floor Coating

We no longer stock this product, but can recommend 304 HB Epoxy Floor Coating as a great alternative. 304 HD Epoxy Floor Coating is a two-pack solvent free high-build epoxy resin system for application as a heavy duty floor coating for concrete, steel and other substrates. Low odour - Very good chemical resistance - High build Excellent...

Shop now

In stock

109 Tool Cleaner

109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins. Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable This product is for Professional Use Only Images are for illustrative purposes only and may differ from the actual product More...

£53.06 (incl. VAT)

Shop now

In Stock and Available for Delivery

402 Damp Proof Coating

2 pack epoxy resin based primer/coating, which has been developed to function as a residual construction moisture suppressant, allowing the early installation of moisture sensitive flooring in fast track building programmes. Also available in 4,000+ colour options from RAL, BS and NCS Please see 402 Damp Proof Coating - Special Colours...

£120.60 (incl. VAT)

Shop now

In Stock and Available for Delivery

COVERAGE CALCULATOR
Units
Total area²
Or enter length and width dimensions:
Length
Width

502 HD Anti Slip Coating