We are looking to specify Rawlins 503 503 Easy Clean Anti Slip Coating in grey and would we would be grateful if you could provide the LRV (Light Resistance Value) for the standard grey paints please?

We have not carried out LRV testing on the product, however we can advise the RAL colours that are close to the 3 standard greys available in this product and what the LRV is for each colour according to RAL; Light Grey - (Close to RAL 7035) = 58.34 LRV Mid Grey - (Close to RAL 7001) = 31.66 LRV Dark Grey - (Close to RAL 7011) = 12.04 LRV We obviously cannot comment on how the gloss level of 503 Easy Clean Anti Slip Coating and the aggregate contained within the coating would affect RAL's stated Light Reflectance Values but hopefully this at least provides you an approximation of what they may be near. Should you require more exact results you would need to carry out testing on the product yourselves to obtain these. However please note that colours will change somewhat batch to batch so unless you carried out testing on the finished floor areas after they had the 503 Easy Clean Anti Slip Coating applied to them, again results may vary.

I am looking for an outdoor paint in non slip finish. Would this finish be suitable?

Thank you for the enquiry, we have contacted you directly for more information.

We have a retail shop premises with largely various female shoe traffic. The base is non-glazed ceramic tiles over which there are two coats of back general acrylic paint and two coats of white the same (yes we decided on a drastic colour change). The black seems to be pretty fast but the white layers scrape off very easily with footwear and small furniture movement. Obviously we would like to have a much more durable white finish. Will this paint be suitable, or another in your catalogue?

Thank you for the enquiry, assuming the previously painted cermaic tiles are clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Smartkote Protectakote UVR . We would recommend testing for compatibility and adhesion prior to full application on previously applied coatings. . Any bare tile areas should be primed with Smartkote Protectakote Clear Primer Treatment .

Hi - Searching for a suitable floor paint for leisure centre changing room. Will this suit?

This would potentially be a good option depending on the current floor type? Please contact our Technical Team on 0113 2455450 (option 2) or technical@rawlinspaints.com to discuss further.

Can I use 503 Easy Clean Anti Slip Coating for a commercial kitchen? It needs to meet regulations which state the floor coating should be: easy to clean can be disinfected non slip durable impervious (ie do not allow fluid to pass through) non absorbent (do not absorb fluid)

Yes, 503 Easy Clean Anti Slip Coating meets all the requirements you have listed and more. You can apply in one coat to previously painted surfaces (ensure compatibility with a test area) or floors primed with 401 Epoxy Floor Primer / 304 HD Epoxy Floor Coating .

503 Easy Clean Anti Slip Coating

Reference RAW503

Brand Rawlins Paints

Search ID RAW1105

A two-pack solvent-free, high-build epoxy resin coating in 10 colours. Tough, durable and easily applied with excellent adhesion to concrete and steel.

Ideal as a slip and chemical resistant floor coating where a less ‘aggressive’ aggregated finish is required
Ideal for food preparation areas, breweries, abattoirs, bottling factories, warehouses, etc
Also available in 4000+ colours- 503 Easy Clean Anti Slip Coating - Special Colours
Images are for illustrative purposes only and may differ from the actual product
This product is for Professional Use Only

Product customisation

Don't forget to save your customization to be able to add to cart

Colour Group

Size

Finish

£103.72(incl. VAT)

£86.43(ex. VAT)

Quantity

Please choose your colour

Available for Delivery (See Delivery Options Below)

ColourPicker Explained

In general we sort colours for products into 2 main groups - ‘Ready Mixed’ and ‘Tinted’.
Tinted colours will always be more expensive than Ready Mixed colours as they need to be produced at the time of order using a tinting machine dispensing colourant into a base*.
During busy periods, this means that tinted colours could take longer, for example – a ready mixed colour ordered on a 3-5 day delivery might arrive within 3 days, however a tinted colour might take the full 5 days to arrive.

To find Ready Mixed colours, search "ready mixed" or select the Ready Mixed 'colour chart'. To see Tinted colours select a colour chart such as RAL, BS, NCS, etc. or search for a colour/hue to see available or related options.

To ensure fair pricing, we split colours into ‘Price Bands’ to group together similar priced colours. If you wish to search for the cheapest tinted colours, always select Price Band 1.

We make every effort to list all available colours, however we also offer a colour match service which can be accessed by contacting our Technical Team on 0113 245 5450 (option 2) or emailing [email protected]

*Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour

Colour reproduction of the Products on the Site is limited by the technology used to deliver web pages and by the colour representation of Customer’s own monitor and computer set-up. We have made every effort to display as accurately as possible the colours of our Products but we cannot guarantee that the colour shown on Customer’s monitor’s display will accurately reflect the colour of the Product on delivery. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person (and not digitally) to ensure that the colour is acceptable for its purposes.

5 questions about the product

Description

503 Easy Clean Anti-Slip Coating is a two-pack solvent-free, high-build epoxy resin coating containing a hard wearing fine particle anti-slip additive that is pre-dispersed into the resin and held in suspension. The result provides a ‘ready to use’ product that leaves an evenly textured, slip resistant surface that is easy to clean and is extremely durable.

503 Easy Clean Anti-Slip Coating will provide a heavy duty, chemical and abrasion resistant fine textured finish on concrete, steel and other substrates. Applied by roller and paint brush the product is low odour producing a seamless, hard wearing, hygienic floor finish.

Note: We recommend using 502 HD Anti-Slip Coating on ramps, very wet/oily areas or other areas that generally require a high level of slip resistance.

This product is for Professional Use Only.

Recommended Uses:

As a slip and chemical resistant floor coating where a less ‘aggressive’ aggregated finish is required and ease of cleaning is important
Ideal for food preparation areas, breweries, abattoirs, bottling factories, warehouses, etc

Features & Benefits

Solvent free, low odour
Very good chemical resistance
Excellent adhesion to concrete and steel
Even, fine textured finish
Tough, durable and easily applied
Hygienic and easily cleaned
Wide range of colours
Two-pack

Typical Properties

Technical Data
	503 Easy Clean Anti-Slip Coating
Pot life @ 20°C:	45 Minutes
Pot life @ 10°C	90 Minutes
Tack free time @ 20°C:	6 hours
Hard dry time@ 20°C:	10 hours
Full chemical resistance @ 20°C:	7 days
Adhesion strength to concrete:	3.9 MPa (concrete failure)
Adhesion strength to mild steel:	>12 MPa

Chemical Resistance
Chemical	Resistance
Dilute Acids and Alkalis	Excellent
Oil	Excellent
Petrol	Excellent
Diesel	Excellent
Vegetable Oils	Excellent
Raw Sewage	Excellent

Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.

Slip Resistance

Dry PTV: 48-50
Wet PTV: 40-42

PTV Ratings:

Slip potential classifications from Pendulum Test Values.

Slip Resistance Values
PTV	Slip Potential
< 25	High
25 - 35	Moderate
> 35	Low

The above results must only be used as a general guideline as the slip resistance of a cured resin coating can vary considerably due to many factors including: application technique, variations in film thickness, dispersion of the anti-slip texturing additive and the surface variations of the substrate and location to where it will be applied.

To obtain accurate PTV readings that are site specific (if required) it is strongly recommended that a slip assessment pendulum test is undertaken on each specific site after completion of the installation when the resin has fully cured.

A full copy of the official test report is available upon request.

Coverage

A 5kg pack is sufficient to apply one coat to 20m² of surface providing an overall d.f.t. of approximately 200 microns

Surface Preparation

Concrete:

Concrete shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound and existing paint finishes etc
Blow holes and defective concrete shall be made good using 201 Epoxy Repair Mortar
Suitable mechanical treatment such as vacuum grit blasting is the preferred treatment prior to application as this ensures a mechanical ‘key’ for the coating

Steel:

Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish standard
All dust and grease shall be removed prior to coating application
If a delay is likely to occur between blasting and application then it is recommended that a coat of 404 Epoxy Metal Primer is applied as holding primer to obviate flash rusting

Note: Substrates with high moisture content or oil contamination can still be coated in most instances by the inclusion of one of our specialist primers. Please see 402 Damp Proof Coating and 403 Oil Tolerant Primer for full details.

Mixing:

Pour the contents of the curing agent container into the base container and thoroughly mix, preferably by mechanical means until a uniform colour is achieved

Mixing Ratio:

By Volume - 2.44 Base: 1 Curing Agent
By Weight - 100 Base: 28.2 Curing Agent

Application

Apply by brush, roller or airless spray at a nominal rate of 0.25kg/m²
Ensure coverage rates are adhered to – spreading the product too far can result in reduced durability, performance, opacity, etc
Over application can result in reduced or even no slip resistance
This should be applied to an adequately primed or compatible (test if unsure) previously painted surfaces
Existing coatings need to be sound, free of contaminants and checked for compatibility, adequate adhesion and should be abraded to provide a suitable key for 503 Easy Clean Anti-Slip Coating to adhere
Should you wish to build the film build-up of the coating system, first apply a coat of 304 HD Epoxy Floor Coating at a nominal rate of 0.25 to 0.3kg/m²
Ensure the following coat of 503 Easy Clean Anti-Slip Coating is applied after a minimum of 14 hours and before a maximum of 48 hours

Cleaning

Clean equipment with 109 Tool Cleaner prior to curing of the coating

Curing

Allow to cure for a minimum of 24 hours @ 20°C prior to light foot traffic access and 48 hours @ 20° prior to vehicular trafficking
7 days cure @ 20°C is recommended prior to exposure to chemicals - lower temperatures will extend the curing time

Storage & Shelf Life

Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 25°C
503 Easy Clean Anti-Slip Coating has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions

Health & Safety

Avoid contact of the material with skin and eyes
Wear gloves and goggles
Wash off splashes immediately with soap and water
Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
Please refer to Material Safety Data Sheet for additional information
503 Easy Clean Anti-Slip Coating shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]

Product Details

Reference 1105-862939

Data sheet

Manufacturer: Rawlins Paints
For Use By: Professional Use
Water / Solvent Based: Water
For Use On: Concrete, Steel
Application Method: Brush, Roller, Airless Spray
Colour: Standard / Ready Mixed
Single, Two or Three Pack: Two-Pack
Mixing Ratio: By Volume - 2.44 Base: 1 Curing Agent
Fully Cured (at 20°C): 7 Days
Pot Life (at 20°C): 45 Minutes
Coverage: 4m² per KG
Shelf Life (from date of manufacture): 12 months
Touch Dry: 6 Hours
UN Number: UN3082
Base Type: Solvent-Free
Suitable For Use On: Metal
Suitable For Use On: Concrete
Suitable For Use On: Steel
Suitable For Use On: Coated Surfaces
Suitable For Use On: Warehouse Floors
Suitable For Use On: Factory Floors
Suitable For Use On: Warehouses
Suitable For Use On: Workshops
Suitable For Use On: Workshop Floors
Suitable For Use On: Food Preparation Areas
Suitable For Use On: Breweries
Suitable For Use On: Bottling Factories
Suitable For Use On: Brewery Floors
Suitable For Use On: Abattoir Floors
Finish: Textured Gloss
Application Method: Brush
Application Method: Roller
Application Method: Spray
Components: 2K
Usages: Anti-Slip
Product Usage Type: Topcoat
Product Category: Paints
Colour Family: Grey
Colour Family: Green
Colour Family: Blue
Colour Family: Red
Colour Family: Yellow
Colour Family: Black
Colour Family: White
Anti-Slip Texture: Fine Texture
Product Focus: Scrubbable Paints
Product Type: Epoxy

Attachments

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

Name ^*

Email ^*

Question ^*

^* Required fields

I have read and agree to the conditions of use (read)

Steven Cromb on 2022-04-21 16:22:43	Question: We are looking to specify Rawlins 503 503 Easy Clean Anti Slip Coating in grey and would we would be grateful if you could provide the LRV (Light Resistance Value) for the standard grey paints please?
	Answer from Rawlins’ Technical Team: We have not carried out LRV testing on the product, however we can advise the RAL colours that are close to the 3 standard greys available in this product and what the LRV is for each colour according to RAL; Light Grey - (Close to RAL 7035) = 58.34 LRV Mid Grey - (Close to RAL 7001) = 31.66 LRV Dark Grey - (Close to RAL 7011) = 12.04 LRV We obviously cannot comment on how the gloss level of 503 Easy Clean Anti Slip Coating and the aggregate contained within the coating would affect RAL's stated Light Reflectance Values but hopefully this at least provides you an approximation of what they may be near. Should you require more exact results you would need to carry out testing on the product yourselves to obtain these. However please note that colours will change somewhat batch to batch so unless you carried out testing on the finished floor areas after they had the 503 Easy Clean Anti Slip Coating applied to them, again results may vary.

Ross McNally on 2021-06-12 10:16:36	Question: I am looking for an outdoor paint in non slip finish. Would this finish be suitable?
	Answer from Rawlins’ Technical Team: Thank you for the enquiry, we have contacted you directly for more information.

Colin Magee on 2021-05-12 20:11:09	Question: We have a retail shop premises with largely various female shoe traffic. The base is non-glazed ceramic tiles over which there are two coats of back general acrylic paint and two coats of white the same (yes we decided on a drastic colour change). The black seems to be pretty fast but the white layers scrape off very easily with footwear and small furniture movement. Obviously we would like to have a much more durable white finish. Will this paint be suitable, or another in your catalogue?
	Answer from Rawlins’ Technical Team: Thank you for the enquiry, assuming the previously painted cermaic tiles are clean, dry, sound and prepared as detailed in the Technical data sheet we can recommend Smartkote Protectakote UVR. We would recommend testing for compatibility and adhesion prior to full application on previously applied coatings. . Any bare tile areas should be primed with Smartkote Protectakote Clear Primer Treatment.

emma on 2019-08-05 11:23:31	Question: Hi - Searching for a suitable floor paint for leisure centre changing room. Will this suit?
	Answer from Rawlins’ Technical Team: This would potentially be a good option depending on the current floor type? Please contact our Technical Team on 0113 2455450 (option 2) or [email protected] to discuss further.

lizzie on 2015-08-27 08:34:19	Question: Can I use 503 Easy Clean Anti Slip Coating for a commercial kitchen? It needs to meet regulations which state the floor coating should be: easy to clean can be disinfected non slip durable impervious (ie do not allow fluid to pass through) non absorbent (do not absorb fluid)
	Answer from Rawlins’ Technical Team: Yes, 503 Easy Clean Anti Slip Coating meets all the requirements you have listed and more. You can apply in one coat to previously painted surfaces (ensure compatibility with a test area) or floors primed with 401 Epoxy Floor Primer / 304 HD Epoxy Floor Coating.

IMPORTANT SHIPPING & DELIVERY INFORMATION

503 Easy Clean Anti Slip Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

201 Epoxy Repair Mortar

201 Epoxy Repair Mortar is a high strength, trowel applied, two component epoxy resin mortar, designed for rapid and permanent repairs to concrete and masonry surfaces. Pre-packed units – ready to use Fast curing Impact and abrasion resistant Frost resistant and impervious to water Negligible shrinkage Images are for illustrative...

£43.42 (incl. VAT)

Shop now

In Stock and Available for Delivery

403 Oil Tolerant Primer

Developed for use in applications to oil contaminated floors prior to application of subsequent floor toppings. The product exhibits outstanding adhesion to concrete and other substrates and is particularly suitable where compromised surfaces exist. Solvent free, low odour Excellent adhesion to concrete and steel Surface tolerant...

£132.66 (incl. VAT)

Shop now

In Stock and Available for Delivery

404 Epoxy Metal Primer

2 pack, water-based, epoxy, anti-corrosive primer designed for the protection of steelwork. Non toxic Fast drying - touch dry in 1-2 hours @ 20ºC May be applied to damp or dry surfaces Excellent anti-corrosive properties Compatible with a wide range of top coats Long overcoating window Easily applied Very good adhesion Early water...

£45.35 (incl. VAT)

Shop now

In Stock and Available for Delivery

304 HD Epoxy Floor Coating

We no longer stock this product, but can recommend 304 HB Epoxy Floor Coating as a great alternative. 304 HD Epoxy Floor Coating is a two-pack solvent free high-build epoxy resin system for application as a heavy duty floor coating for concrete, steel and other substrates. Low odour - Very good chemical resistance - High build Excellent...

Shop now

In stock

502 HD Anti Slip Coating

A 3-pack solvent-free high-build epoxy resin system in 10 colours for application as a heavy duty non-slip floor coating for concrete, metal and wood surfaces requiring high levels of slip resistance. Ideal for use in high traffic areas requiring high slip resistance such floors, stairs, ramps, loading bays Also suitable for chemical plant...

£107.34 (incl. VAT)

Shop now

In Stock and Available for Delivery

109 Tool Cleaner

109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins. Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable This product is for Professional Use Only Images are for illustrative purposes only and may differ from the actual product More...

£53.06 (incl. VAT)

Shop now

In Stock and Available for Delivery

402 Damp Proof Coating

2 pack epoxy resin based primer/coating, which has been developed to function as a residual construction moisture suppressant, allowing the early installation of moisture sensitive flooring in fast track building programmes. Also available in 4,000+ colour options from RAL, BS and NCS Please see 402 Damp Proof Coating - Special Colours...

£120.60 (incl. VAT)

Shop now

In Stock and Available for Delivery

503 Easy Clean Anti Slip Coating