- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Axalta Bondon 115 Aluminium Primer is a surface tolerant two pack epoxy aluminium primer, used as a primer on hand prepared rusty steel and to upgrade sound existing coatings.
- Use as a rust inhibiting primer on hand prepared steel, or as a high build patch repair primer under most generic coating types
- Approved to UK Network Rail specification as the primer of a 3 coat system applied to manually prepared steelwork
- Excellent anticorrosive protection
- Use to upgrade a conventional system to high performance epoxy/polyurethane system
- Good chemical and solvent resistance
Axalta Bondon 115 Aluminium Primer is a surface tolerant two pack epoxy aluminium primer, used as a primer on hand prepared rusty steel and to upgrade sound existing coatings.
Approvals/Certification - UK Network Rail M24 (Item 7.1.5)
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Use as a rust inhibiting primer on hand prepared steel, or as a high build patch repair primer under most generic coating types.
- Approved to UK Network Rail specification as the primer of a 3 coat system applied to manually prepared steelwork.
- Excellent anticorrosive protection.
- Excellent ‘wetting’ properties for application to a manually prepared steel surface.
- Use to upgrade a conventional system to high performance epoxy/polyurethane system.
- Good chemical and solvent resistance.
- Use as a single coat system under insulation (see Product Notes further below).
Product Specification
Technical Data | |
---|---|
Volume Solids | 80 ± 2% |
VOC Content | 168 + 20 g/litre |
SG | 1.41 kg/lt mixed |
Storage Conditions | Store in dry, cool conditions and protect from frost. |
Shelf Life | Minimum 12 months if stored as above in unopened containers. |
Flash Point | 23-60℃ |
Pot Life | 2 hours at 23℃ |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
Minimum | 125 µm | 157 µm | 6.4 m² /litre |
Maximum | 200 µm | 250 µm | 4.0 m² /litre |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. |
Drying Times
Product Data | |||||
---|---|---|---|---|---|
Applied to 125 microns DFT | 10℃ | 23℃ | 35℃ | ||
Dust Free | 5 hr | 3 hr | 2.5 hr | ||
Hard Dry | 24 hr | 12 hr | 10 hr | ||
Overcoating* | Minimum | 18 hr | 15 hr | 12 hr | |
Maximum | 12 Weeks | ||||
*See Product Notes | |||||
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation. |
Surface Preparation
- All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams.
- Blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50-75 microns.
- Where blast cleaning is impractical the surface should be prepared to St2 (ISO 8501-1:2007) taking care to avoid ‘polishing’ the surface.
- Can be used as a brush or spray applied primer when water abrasive blast cleaning. Allow to dry and lightly wire brush if powdery deposits form.
Mixing
Mix only in the proportions stated, mixing each component individually then together using a mechanical agitator. Agitate periodically during use to ensure product remains homogeneous.
Thinner
Equipment Cleaner - 950 Thinner
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying and curing.
- Do not apply when rain, mist, sleet or snow are imminent.
- During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3ºC above the dew point.
- Only apply this product when the above conditions can be maintained throughout the critical application and drying/curing process.
- Paint temperature should ideally be at a minimum of 15ºC.
Application Methods
Method | Airless Spray | Conventional Spray | Brush | Roller |
---|---|---|---|---|
Yes | No | Yes | No |
- Airless Spray: Output fluid pressure at tip 2000-3000 psi, Tip Size: 13-21 thou (0.33-0.53mm).
- Apply by brush over manually prepared bare steel surfaces.
- If applying by roller over blast cleaned steel, there is a tendency to over-spread the coating resulting in low film builds. If this occurs a second coat should be applied to achieve the desired film build.
- Refer to Axalta Coating Systems ‘Epoxy Application and Curing Notes’.
Product Notes
- Overcoating: If overcoating with products other than itself or Bondon 116, please consult our technical team for advice.
- Extend min/max drying and overcoating times at lower temperatures and for DFTs above 125 microns.
- Do not apply or cure below 5ºC.
- Colour changes can occur in exposed conditions and will occur at elevated temperatures.
- Moisture in the can may cause pressure build up.
Health & Safety
Containers are provided with safety labels which should be observed. Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets. A Safety Data Sheet for this product is available on request from the attachments section above.
Data sheet
- For Use By
- Professional Use
- Water / Solvent Based
- Solvent
- For Use On
- Steel
- Application Method
- Brush
Roller
Spray - Sheen
- Mid Sheen
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Product Certifications
- UK Network Rail M24
- Pack Size
- 5L
- Touch Dry (at 20°C)
- 3 hr
- Dry to Handle (at 20°C)
- 15hr
- Coverage
- 6.4m² per litre
- Recommended Thinner/Cleaner
- No. 5 Thinner
- Min. Application Temperature
- Steel temperature should remain at least 3ºC above the dew point. Paint temperature should ideally be at a minimum of 15ºC.
- VOC
- 168 + 20 g/litre
- Shelf Life (from date of manufacture)
- Minimum 12 months if stored as above in unopened containers
- Recommended Dry Film Thickness
- Min: 125 µm - Max: 200 µm
- Recommended Wet Film Thickness
- Min: 157 µm - Max: 250 µm
- UN Number
- UN1263
- Suitable For Use On
- Aluminium
- Suitable For Use On
- Steel
- Suitable For Use On
- Rubber
- Suitable For Use On
- Vinyl
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Airless Spray
- Manufacturer
- Axalta
- Components
- 2K
- Product Usage Type
- Primer
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta Bondon 115 Aluminium Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Axalta 1031 Thinner
Axalta 1031 Thinner, for use with the Axalta range of coatings, has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray. Can also be used for the cleaning of some surfaces prior to application of the coating...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Axalta Bondon 116 Epoxy Primer & Undercoat
Axalta Bondon 116 Epoxy Primer & Undercoat is a high solids two pack epoxy intermediate or finish, designed for application over Axalta Bondon 115. Approved over Bondon 115 by UK Network Rail Can be used as part of a surface tolerant epoxy system which can upgrade sound old conventional coatings to a high performance epoxy/polyurethane...