- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Axalta Bondon 116 Epoxy Primer & Undercoat is a high solids two pack epoxy intermediate or finish, designed for application over Axalta Bondon 115.
- Approved over Bondon 115 by UK Network Rail
- Can be used as part of a surface tolerant epoxy system which can upgrade sound old conventional coatings to a high performance epoxy/polyurethane specification
- Available in silver as standard; over 350+ RAL and BS shades to suit all finishing shades available made to order, 400 litre minimum order quantity. Please contact our sales team with your requirements on 0113 2455450 or send a message to [email protected]
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour. For information regarding alternate colours, please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
Axalta Bondon 116 Epoxy Primer & Undercoat is a high solids two pack epoxy intermediate or finish, designed for application over ViterBond ST200. Approved to UK Network Rail specification as the intermediate coat of a 3 coat system. Ideal use to upgrade a conventional system to a high performance epoxy/polyurethane system.
Approvals/Certification - UK Network Rail M24 (Item 7.1.7)
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Cures down to 2℃.
- Approved to UK Network Rail specification as the intermediate coat of a 3 coat system.
- Applied as a two coat system over ViterBond ST200 or WG200 to provide 250 microns dft in 2 brush coats.
- Good chemical and solvent resistance.
- Use to upgrade a conventional system to high performance epoxy/polyurethane system.
- Can overlap onto aged, sound chlorinated rubber, vinyl or alkyd products.
- Suitable for either winter or summer application.
Product Specification
Technical Data | |
---|---|
Volume Solids | 80 ± 2% |
VOC Content | 173 + 20 g/litre |
SG | 1.28 – 1.32 kg/lt mixed. |
Storage Conditions | Store in dry, cool conditions and protect from frost. |
Shelf Life | Minimum 12 months if stored as above in unopened containers. |
Flash Point | 23-60℃ |
Pot Life | 3½ hours at 23℃ |
Mixing Ratio | Base: 1 part by volume. Hardener: 1 part by volume |
Film Thickness Range And Coverage
Product Data | |||||
---|---|---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |||
Minimum | 125 µm | 152 µm | 6.6 m² /litre | ||
Maximum | 200 µm | 244 µm | 4.1 m² /litre | ||
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. |
Drying Times
Product Data | |||||
---|---|---|---|---|---|
Applied to 125 microns DFT | 5℃ | 10℃ | 23℃ | ||
Dust Free | 9 hr | 6 hr | 3 hr | ||
Hard Dry | 15 hr | 10 hr | 6 hr | ||
Overcoating* | Minimum | ||||
Maximum | Indefinite if clean and sound and sound, with itself | ||||
*See Product Notes | |||||
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation. |
Surface Preparation
- All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams.
- This product is an intermediate/finish coat and should be applied over an appropriate primer or intermediate coat, such as ViterBond ST200 or ViterBond WG200 primers.
Mixing
Mix only in the proportions stated, mixing each component individually then together using a mechanical agitator. Agitate periodically during use to ensure product remains homogeneous.
Thinner
Equipment Cleaner - 950 Thinner
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying and curing.
- Do not apply when rain, mist, sleet or snow are imminent.
- During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3ºC above the dew point.
- Only apply this product when the above conditions can be maintained throughout the critical application and drying/curing process.
Application Methods
Method | Airless Spray | Conventional Spray | Brush | Roller |
---|---|---|---|---|
Yes | No | Yes | No |
- Airless Spray: Output fluid pressure at tip 2000-3000 psi, Tip Size: 19-27 thou (0.48-0.68mm).
- Brush application will typically achieve up to 125 microns dft, airless spray up to 200 microns dft.
- Avoid exceeding the maximum stated dry film thickness.
- Refer to Axalta Coating Systems ‘Epoxy Application and Curing Notes’.
Product Notes
- Overcoating with conventional, chlorinated rubber or vinyl: ideally overcoat between 24-48 hours at 23ºC. Maximum is 7 days or abrading is required.
- Overcoating with epoxy or two pack polyurethane:min 24 hours, max 3 months, at 23ºC.
- Overcoating with alkyds: starting with ViterLac AM112 MIO is recommended for good intercoat adhesion. Min 24 hours, max 7 days, or abrading will be required.
- Extend min/max drying and overcoating times at lower temperatures and for DFTs above 125 microns
- Do not apply below 2ºC.
Health & Safety
Containers are provided with safety labels which should be observed. Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets. A Safety Data Sheet for this product is available on request from Axalta Coating Systems or from the attachments section above.
Data sheet
- Water / Solvent Based
- Solvent
- For Use On
- Metal
- Application Method
- Brush, Spray
- Sheen
- Semi-gloss
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Two-Pack
- Product Certifications
- UK Network Rail M24
- Pack Size
- 5L
- Key Features
- Approved over ST200 by UK Network Rail. Cures down to 2°C. Wide colour range.
- Touch Dry (at 20°C)
- 3 hr
- Dry to Handle (at 20°C)
- 6 hr
- Pot Life (at 20°C)
- 3½ hours at 23℃
- Coverage
- 6.6m² per litre
- Recommended Thinner/Cleaner
- Axalta 1031 Thinner
- Min. Application Temperature
- Steel temperature should remain at least 3ºC above the dew point.
- VOC
- 173 + 20 g/litre
- Shelf Life (from date of manufacture)
- Minimum 12 months if stored as above in unopened containers
- Touch Dry
- 3 hours
- Recommended Dry Film Thickness
- Min: 125 µm - Max: 200 µm
- Recommended Wet Film Thickness
- Min: 152 µm - Max: 152 µm
- UN Number
- UN1263
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta Bondon 116 Epoxy Primer & Undercoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Axalta ViterBond ST200 Epoxy ST Primer
We no longer stock this product, but can recommend Axalta Bondon 115 as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450...
Axalta 1031 Thinner
Axalta 1031 Thinner, for use with the Axalta range of coatings, has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray. Can also be used for the cleaning of some surfaces prior to application of the coating...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...