- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Kovertek TekPur SP is a single component polyurethane refurbishment system that forms a seamless membrane on interior & exterior surfaces. Suitable for repairs, overlaying, waterproofing and more on a wide range of substrates. Please refer to substrate guide below for a list of applicable surfaces.
- Superior UV & weather resistance
- Cold applied
- Can be applied in a single coat
- Fast curing and bubble-free
- For Professional Use Only
KoverTek TekPur SP is a single component fast curing polyurethane that forms a consistent bubble free seamless membrane, offering superior UV and weather resistance and can be applied in a single coat to achieve a high tensile, durable finish. Can be used without reinforcement where movement is limited.
TekPur SP should be applied by professional roofers experienced in cold lay wet on wet systems. TekPur can be applied to most substrates as a waterproofing system & for concrete structures, concrete roadways under tarmac layers, carparks, ramps, bridges etc.
Quick Links - Click To Jump To Section:
Features & Benefits
- Remains elastic at -40°C and does not soften at high temperatures (80°C+)
- Exceptional toughness with flexural strength
- TekPur SP has a 10 year material guarantee when used in conjunction with TekVeil Reinforcement
- Can be used with or without TekVeil for repairs and overlaying existing surfaces
- Can be used for waterproofing concrete structures, tarmac layers, ramps, bridges & more
- Excellent UV and weather resistance
- Fast skin formation, bubble free
- Cold Applied
- Breathable membrane
Substrate Guide
Recommended surfaces for waterproofing and protection | |
OSB3 T&G | Prime with TekPrime SD |
Asphalt, Bitumen and Felt Roofs | Prime with TekPrime SD |
EPDM Membranes | Prime with TekPrime SD |
Single Ply Membranes | Prime with TekPrime PVC |
GRP/Fibreglass Surfaces | Prime with TekPrime SD |
Gypsum/Cement Boards | Prime with TekPrime SD |
Concrete Roofs | Prime with TekPrime SD |
Cement Fibre & Metal Roof Sheets | Prime with TekPrime SD |
Plastisol Metal | Prime with TekPrime PVC |
PIR Insulation Boards | Prime with TekPrime SD |
NB: When applying to any surface a primer must be used prior to application and when applying to Single ply or Plastisol surfaces then TekPrime PVC must be used instead of TekPrime SD (same day primer)
Not suitable for unsound surfaces, swimming pools in contact with chemically treated water or fishponds.
PLEASE NOTE – There are many variations of the surfaces listed as suitable, however care must be taken in testing a small area prior to commencing the main body of work to ensure that a suitable bond is achieved, we do not recommend for use on areas over 200m² in one continuous area. Please contact our Technical Team to discuss larger projects.
Surface Preparation
The area to be treated should be first cleaned with a high-pressure washer or a stiff bristled broom and soapy water to remove grease, oil, wax or any other surface contaminants and loose particles. Any defects in the surface such as cracks, splits and blisters need to be treated prior to application, surfaces that are irregular should be filled with a suitable material. Allow all surfaces to dry before commencing work.
Kovertek TekPrime SD and TekPrime PVC is required before the application of TekPur SP, the type of primer and coverage is dependent on the surface type and porosity. Allow primer to fully dry before application.
Gaps in the substrate/surface above 2mm or subject to movement needs to be filled with a non-silicone product. If applying onto OSB3 boards the joints need to be taped with TekTape Self-Adhesive Butyl Tape; tape should be applied centrally to joints.
Surfaces must be recoated within a maximum 48 hours from the first coat, if this is exceeded another coat of primer must be applied to avoid delamination of the layers.
Application
Mix using a low-speed mixer set to a maximum of 300rpm, mix thoroughly to the base of the container avoiding adding air into the product which can create air bubbles.
Carry out any detailing and perimeter works prior to the application onto the main areas.
TekPur SP can be applied with a suitable short/mid pile roller, brush or squeegee. Apply either one thicker coat at minimum 2kg per m2 or 2 thinner layers at the same application rate. No longer than 48 hours should be taken to apply the second coat, otherwise the TekPrime will need to be used again.
Data sheet
- Manufacturer
- Kovertek
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior & Exterior
- For Use On
- Concrete
Tarmac
Asphalt
Ramps
Bridges
Roofs
Balconies - Application Method
- Brush
Roller
Squeegee - Single, Two or Three Pack
- Single
- Pack Size
- 6KG
15KG
25KG - Dry to Recoat (at 20°C)
- Between 6-18 hours
- Fully Cured (at 20°C)
- Approx. 48 hours
- Walk-on Time
- Approx. 6 hours (@20°C)
- Working Time
- Approx. 60 minutes (@20°C)
- Suitable For Use On
- Concrete
- Suitable For Use On
- Tarmac
- Suitable For Use On
- Asphalt
- Suitable For Use On
- Balconies
- Suitable For Use On
- Ramps
- Suitable For Use On
- Roofs
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Squeegee
- Manufacturer
- Kovertek
- Components
- 1K
- Usages
- Weatherproofing
- Product Usage Type
- Topcoat
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
KoverTek TekPur SP Polyurethane is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
KoverTek TekPur SD Same Day Primer
A single component same day primer suitable for almost all substrates. Ideal as a cost-effective sealer on dry and wet concrete, as well as concrete classed as 'green'. Cures quickly, making it ideal for same-day use or application in colder conditions. Can be used on porous and non-porous substrates Can seal damp surfaces Tack-free and...
KoverTek TekPrime PVC Primer
KoverTek TekPrime PVC Primer is an acetone primer suitable for cleaning and priming surfaces prior to application of other KoverTek products. Fast flash-off; Suitable substrates include: Metals including Lead Single Ply surfaces Plastic surfaces such as UPVC and Plastisol