- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
2 pack, fast curing coating in 10 colours designed to provide a dust-free, seamless floor finish with protective and decorative properties on concrete and steel surfaces. The inherent slip resistance of the coating may be enhanced by the incorporation of 504 Standard Anti Slip Aggregate.
- Also available in 4,000+ colour options from RAL, BS and NCS
- Please see 701 MMA Floor Coating - Special Colours
- Tough and abrasion resistant
- Colour stable
- Very good chemical resistance
- Rapid curing minimises down times and ensures a fast return to service
- Accepts light foot traffic in 1 hour @ 20°C
- Suitable in wet areas
- Hygienic and easily cleaned
- Cures at low temperatures (as low as -20°C)
- Hot water and fat resistant to 80°C
- Images are for illustrative purposes only and may differ from the actual product
- This product is for Professional Use Only
Product customisation
Don't forget to save your customization to be able to add to cart701 MMA Floor Coating is a two pack, fast curing coating designed to provide a dust-free, seamless floor finish with protective and decorative properties. The inherent slip resistance of the coating may be enhanced by the incorporation of 504 Standard Anti Slip Aggregate.
701 MMA Floor Coating can be trafficked after just 1 hour (see ‘curing’ for full details), allowing a fast return to service and can be applied at temperatures as low as -20°C.
This product is for Professional Use Only.
Recommended Uses:
- As a rapid curing, abrasion and chemical resistant floor coating where minimal downtime is paramount
Quick Links - Click To Jump To Section:
- Features & Benefits
- Typical Properties
- Coverage
- Surface Preparation
- Application
- Cleaning
- Curing
- Limitations
- Storage & Shelf Life
- Health & Safety
Features & Benefits
- Can be applied at temperatures as low as -20°C
- Tough and abrasion resistant
- Can be trafficked after just 1 hour
- Colour stable
- Very good chemical resistance
- Two-pack
- Rapid curing minimises down times and ensures a fast return to service
- Suitable in wet areas
- Hygienic and easily cleaned
- Hot water and fat resistant to 80°C
Typical Properties
Technical Data | |
---|---|
701 MMA Floor Coating | |
Pot life @ 20°C: | 15-20 Minutes |
Pot life @ 10°C | 25-30 minutes |
Tensile strength: | 20N/mm² |
Elongation at break: | 2% |
Flexural strength: | 37N/mm² |
Adhesion to concrete: | 3.8N/mm² (concrete failure) |
Adhesive strength to grit blasted steel: | 12N/mm² |
Temp. range during application: | -20°C to + 40°C |
Temp. range during service: | -20°C to + 80°C |
Chemical Resistance | |
---|---|
Chemical | Resistance |
Dilute Acids and Alkalis | Excellent |
Oil | Excellent |
Petrol | Excellent |
Diesel | Excellent |
Vegetable Oils | Excellent |
Fruit Juices | Excellent |
Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for specific advice.
Coverage
- A 5kg pack is sufficient to cover an area of 8.3m² with the recommended two coat treatment, providing a minimum thickness of 500 microns
Surface Preparation
- Concrete surfaces shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%
- Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes, etc
- Blow holes and defective concrete shall be made good using 710 MMA Repair Mortar
- Suitable mechanical treatment, such as vacuum grit blasting, is the preferred treatment prior to application as this ensures a mechanical ‘key’ which will optimise adhesion
- Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish Standard
- All dust shall be removed prior to coating application. A coat of 707 MMA Metal Primer shall be applied as soon as practicable after blasting, in order to obviate the possible occurrence of ‘flash rusting’
Priming:
- Concrete surfaces shall be primed with a coat of 706 MMA Floor Primer, applied by brush or roller, at a nominal rate of 0.3kg/m²
- Long nap lambswool rollers are recommended for primer application
- Allow primer to cure for a minimum of 40 minutes
- Steel surfaces shall be primed with 707 MMA Metal Primer as soon as practicable after blasting
- Damp concrete surfaces can be primed using 709 MMA Damp Proof Primer – refer to product data sheet for full details
Mixing:
- 701 MMA Floor Coating is supplied as a two pack material consisting of the base component, and the catalyst component, incorporate the catalyst component into the base component under mechanical stirring, and mix for 1-2 minutes
Mixing Ratio:
- (% Catalyst by Weight) = 1.8
Application
- Apply 701 MMA Floor Coating using short nap perlon, or smooth lambswool rollers at a nominal rate of 0.30kg/m²
- Following a minimum of 1 hour apply a second coat at the same nominal rate
- Should a slip resistant or skid resistant finish be required then broadcast 504 Standard Anti Slip Aggregate onto the first coat within 10 minutes of application
- Following a minimum of 1 hour, sweep off excess aggregate and apply a second coat of 701 MMA Floor Coating
Note: 701 MMA Floor Coating may be applied at greater thicknesses should service conditions warrant it.
Cleaning
- Clean equipment with 109 Tool Cleaner prior to the curing of the coating
Curing
- Light Foot Traffic: 1 hour @ 20°C
- Vehicular Traffic: 2 Hours @ 20°C
- Full chemical resistance: 24 hours @ 20°C
Limitations
- Do not apply to wet, uncured or un-primed concrete surfaces
701 MMA Floor Coating will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered
Storage & Shelf Life
- Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
- Adequate ventilation of the storage area should be provided
- Keep container tightly closed when not in use
- 701 MMA Floor Coating has a minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions
Health & Safety
701 MMA Floor Coating is flammable during application, so adequate safety precautions should be observed.
- Avoid contact of the material with skin and eyes
- Wear gloves and goggles
- Wash off splashes immediately with soap and water
- Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
- Please refer to Material Safety Data Sheet for additional information
- 701 MMA Floor Coating shall be applied strictly in accordance with the manufacturer’s instructions
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Data sheet
- Manufacturer
- Rawlins Paints
- For Use By
- Professional Use
- Interior / Exterior Use
- Interior Use
- Water / Solvent Based
- Solvent
- For Use On
- Concrete, Steel
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Product Certifications
- Sa 2.5 Swedish Standard
- Pack Size
- 5KG
- Coverage
- 3.2m² per KG
- Tensile Strength
- 20N/mm²
- Max. Application Temperature
- 40°C
- Min. Application Temperature
- -20°C
- Touch Dry
- 1 Hour
- UN Number (Activator)
- UN3106
- UN Number (Base)
- UN1866
- Elongation at break
- 2%
- Base Type
- Solvent-Based
- Base Type
- MMA
- Suitable For Use On
- Concrete
- Suitable For Use On
- Steel
- Finish
- Satin
- Application Method
- Roller
- Components
- 2K
- Product Usage Type
- Topcoat
- Product Category
- Paints
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
701 MMA Floor Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
504 Standard Anti Slip Aggregate
504 Standard Anti Slip Aggregate is a specially formulated quartz aggregate to be added to various products in our floor coatings range to provide increased `anti-slip` properties in both dry and wet conditions to improve safety. Produces a rough, non-skid surface Hard wearing and chemical resistant Coloured Quartz Aggregate 0.4-0.8mm...
706 MMA Floor Primer
A rapid curing, general purpose primer enabling fast overcoating. The product exhibits outstanding adhesion to concrete, as well as steel, masonry, and marine plywood, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds. Ideal for use as a rapid curing primer for concrete, steel, masonry,...
707 MMA Metal Primer
A rapid curing three-pack primer for steel, galvanised steel, aluminium, and unglazed ceramic tiles to be used prior to any of the MMA range of coatings, mortars, and screeds. Rapid cure, even at low temperatures - from as low as -30°C* Very good corrosion resistance Excellent adhesion Impervious to water Pre-packed units ready for use...
709 MMA Damp Proof Primer
Developed as a primer for damp concrete, being used prior to any of our MMA range of coatings, mortars, and screeds. Rapid cure, even at low temperatures - from as low as -30°C*. Very good chemical resistance. Excellent adhesion to damp concrete. Impervious to water. Pre-packed units ready for use. Easily applied. Can be overcoated...
710 MMA Repair Mortar
710 MMA Repair Mortar is a fast curing, high strength, trowel applied, three component methacrylate resin mortar, designed for rapid and permanent repairs to concrete and masonry surfaces. Resilient Very good chemical resistance Excellent adhesion Fast curing, even at low temperatures (down to -10°C*) Impact and abrasion resistant...
109 Tool Cleaner
109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins. Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable This product is for Professional Use Only Images are for illustrative purposes only and may differ from the actual product More...