Follow us on:

710 MMA Repair Mortar
710 MMA Repair Mortar

710 MMA Repair Mortar

RAW710
RAW1124

710 MMA Repair Mortar is a fast curing, high strength, trowel applied, three component methacrylate resin mortar, designed for rapid and permanent repairs to concrete and masonry surfaces.

  • Resilient
  • Very good chemical resistance
  • Excellent adhesion
  • Fast curing, even at low temperatures (down to -10°C*)
  • Impact and abrasion resistant
  • Frost resistant and impervious to water
  • Accepts foot trafficking after a minimum of 1 hour @ 20°C
  • Excellent mechanical properties
  • Ideal for repairs to spalled or damaged concrete, bedding pre-cast concrete beams, chemical bunds and floor repairs
  • Images are for illustrative purposes only and may differ from the actual product
  • This product is for Professional Use Only

*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]

Colour
Size
£92.62(incl. VAT)
£77.18(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

710 MMA Repair Mortar is a fast curing, high strength, trowel applied, three component methacrylate resin mortar, designed for rapid and permanent repairs to concrete and masonry surfaces.

The product is ideal for repairs to spalled or damaged concrete, bedding pre-cast concrete beams, chemical bunds and floor repairs.

This product is for Professional Use Only.



Quick Links - Click To Jump To Section:




Features & Benefits


  • High strength
  • Trowel applied
  • Designed for rapid and permanent repairs to concrete and masonry surface
  • Resilient
  • Very good chemical resistance
  • Excellent adhesion
  • Fast curing, even at low temperatures (down to -10°C*)
  • Impact and abrasion resistant
  • Frost resistant and impervious to water
  • Accepts foot trafficking after a minimum of 1 hour @ 20°C
  • Three pack
  • Excellent mechanical properties

*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]



Typical Properties


Technical Data
  710 MMA Repair Mortar
Density: 2,010kg/m³
Pot life @ 20°C: 20 Minutes
Compressive strength: 45MPa
Taber abrasion resistance: 45mg weight loss (CS17 wheels; 1kg loads; 1,000 cycles)
Adhesion to concrete: 3.7MPa (concrete failure)
Temp. range during application: -10°C* to + 40°C
Temp. range during service: -40°C to + 50°C



*Please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]



Chemical Resistance
Chemical Resistance
Dilute Acids and Alkalis Excellent
Oil Excellent
Petrol Excellent
Diesel Excellent



Coverage


  • A 10kg pack yields 5 litres of mortar, sufficient for 1m² @ 5mm thickness



Surface Preparation


  • Remove all laitance, spalled concrete, grease, oil, dust, and other contaminants by scabbling, bush hammering, or other mechanical treatment, to provide a sound clean substrate
  • Any exposed reinforcing steel shall be fully exposed by cutting out around its full circumference, and cleaned by hand abrading or wire brushing to remove rust, scale, etc., and primed with a coat of 706 MMA Floor Primer



Priming:

  • The prepared concrete surface, together with the pre-primed re-bars, shall be primed by the application of 706 MMA Floor Primer
  • The mixed 706 MMA Floor Primer should be applied by brush or roller at a nominal rate of 0.2 – 0.3kg/m², depending upon surface profile
  • Allow the primer to cure for a minimum of 40 minutes



Mixing:

  • 710 MMA Repair Mortar is supplied as a three component product consisting of the base component, the catalyst component and the aggregate component
  • The contents of the base and catalyst component should be thoroughly mixed together and the aggregate then introduced
  • A low speed drill stirrer or a forced action mixer such as a Mixall, Pennine or Creteangle type, will be suitable



Mixing Ratio:

  • (% Catalyst by Weight) = 2.5



Application


  • 710 MMA Repair Mortar should be applied by tamping and trowelling to ensure good compaction and a tight finish
  • The material should not be feather edged
  • Minimum application thickness is 4mm



Cleaning




Curing


  • Allow a minimum cure time of 1 hour @ 20°C prior to foot trafficking and 2 hours @ 20ºC prior to full trafficking



Limitations


  • Do not apply to wet, uncured or unprimed concrete surfaces

710 MMA Repair Mortar will taint food during application, so that all foodstuffs in the immediate vicinity must be removed or properly covered.



Storage & Shelf Life


  • Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C
  • Adequate ventilation of the storage area should be provided
  • Keep container tightly closed when not in use
  • 710 MMA Repair Mortar has a minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions



Health & Safety


710 MMA Repair Mortar is flammable during application, so adequate safety precautions should be observed.

  • Avoid contact of the material with skin and eyes
  • Wear gloves and goggles
  • Wash off splashes immediately with soap and water
  • Any eye contamination must be rapidly irrigated with copious amounts of clean water, and immediate medical attention sought
  • Please refer to Material Safety Data Sheet for additional information
  • 710 MMA Repair Mortar shall be applied strictly in accordance with the manufacturer’s instructions

For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]



Product Details
1124-61698

Data sheet

Manufacturer
Rawlins Paints
For Use By
Professional Use
For Use On
Concrete
Application Method
Trowel
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Three-Pack
Pack Size
10KG
Minimum Applied Thickness
4mm
Pot Life (at 20°C)
20 minutes
Coverage
1m² @ 5mm thick per 10kg
Compressive Strength (at 20°C)
45MPa
Max. Application Temperature
40°C
Min. Application Temperature
-10°C
Density
2,010kg/m³
Touch Dry
1 hour
UN Number (Activator)
UN3106
UN Number (Base)
UN1866
Suitable For Use On
Masonry
Suitable For Use On
Concrete
Application Method
Trowel
Product Category
Paints
Colour Family
Grey
Categorised As
Repairs > Low Temperature Repair Mortars
Seasonal
Cold Weather
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

710 MMA Repair Mortar is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
706 MMA Floor Primer

706 MMA Floor Primer

A rapid curing, general purpose primer enabling fast overcoating. The product exhibits outstanding adhesion to concrete, as well as steel, masonry, and marine plywood, and the fast curing characteristics allow rapid application of subsequent coatings, mortars or screeds. Ideal for use as a rapid curing primer for concrete, steel, masonry,...

Price £135.07 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
109 Tool Cleaner

109 Tool Cleaner

109 Tool Cleaner is a specialist equipment cleaner suitable for the removal of uncured epoxy, polyester and polyurethane resins. Low Hazard Low evaporation rate Excellent solvency powers 80% biodegradable This product is for Professional Use Only Images are for illustrative purposes only and may differ from the actual product More...

Price £53.06 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery