- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
For masonry applications including residential and commercial up to and including three storey buildings. It can be site formed into a built-in or surface fixed cavity tray to manage the downward passage of water in cavity wall applications. It can also be used on sleeper walls below a ground floor construction e.g. beam and block floor system.
- Superior mortar adhesion, ideal for use on buildings where a low imposed load occurs but a high mortar bond is required e.g. parapet walls, beneath masonry coping or capping
- Reduces the risk of masonry slippage due to poor mortar adhesion
- Ideal for use in complex cavity tray detailing e.g. around steel columns, wind posts, parapet posts, etc as the product can be heat bonded on site
- Suitable for cavity trays to openings with solider courses or stone lintels (In accordance with NHBC Technical Guidance 6.1/05)
- Manufactured in excess of British Standard - traditional DPC and cavity tray system
- Excellent mortar adhesion - ideal for low compressive load applications
- Versatile heat bonded material - suitable to form complex or awkward detailing on site
- Modified bituminous coating - laps can be tape bonded or heat bonded
Visqueen Zedex High Bond Damp Proof Course is a heavy duty, traditional DPC and cavity tray system manufactured with a polyester reinforced carrier, rubber modified bituminous coating and surfaced on both sides with a fine silica sand. It is supplied in 8m length rolls and the following widths: 450mm, 600mm, 1000mm.
Quick Links - Click To Jump To Section:
- Approvals and Standards
- System Components
- Storage and Handling
- Preparation
- Installation
- Usable Temperature Range
- Additional Information
Approvals and Standards
- Manufactured in excess of BS 6398:1983 Type A
- Conforms to the specification requirements of NHBC Technical Guidance 6.1/05
- CE Mark EN 13969:2004
- Quality Management System ISO 9001:2015
- Occupational Health and Safety System ISO 45001:2018
- Environmental Management System ISO 14001:2015
System Components
- Visqueen Zedex Jointing Tape, 100mm x 15m
- Visqueen HP Tanking Primer, 5L
- Visqueen Zedex DPC Surface Fixing System
- VisqueenPro Detailing Strip, 300mm x 10m, 500mm x 10m
Storage and Handling
Visqueen Zedex High Bond Damp Proof Course should be stored vertically, under cover in its original packaging.
Care should be taken when handling the product in line with current manual handling regulations.
Preparation
Visqueen Zedex High Bond Damp Proof Course can be cut with a sharp retractable safety knife.
Where the DPC is being fully bonded to the substrate, the surface should be primed with Visqueen HP Tanking Primer and allowed to dry thoroughly.
Material must be warmed above 5°C prior to unrolling.
Installation
DPCs and DPC cavity trays systems to be designed and installed in accordance with the relevant sections of BS 8215:1991, PD 6697:2019 and BS 8000-3:2020.
When built into a masonry wall construction Visqueen Zedex High Bond Damp Proof Course should be installed on an even bed of wet mortar, and any perforations in adjacent courses of masonry should be completely filled with mortar. To ensure mortar adhesion, as soon as possible after laying the DPC, lay at least one further course of masonry including a bed of mortar. Where the specification requires, the DPC can be fully heat bonded to the primed substrate. The DPC must extend through the full thickness of the masonry wall, including pointing, applied rendering or other facing materials.
When used as a site formed cavity tray, the DPC can be either built-in to the inner leaf or surface fixed to the cavity face of the inner leaf.
When surface fixing the cavity tray, the substrate should be primed with Visqueen HP Tanking Primer and allowed to dry. The DPC should be bonded to the inner leaf using Visqueen Zedex Jointing Tape and permanently secured using Visqueen Fixing Strip and fixing suitable for the substrate. Visqueen Fixing Pins for masonry substrates are available.
Complex or awkward junctions e.g. corners, changes of level etc can be effectively sealed on site with the DPC when the lap joints are heat bonded.
All laps should be a minimum of 100mm and either bonded with Visqueen Zedex Jointing Tape or heat bonded with appropriate equipment e.g. propane gas torch.
Usable Temperature Range
For additional detailing information, contact Rawlins Technical on 0113 2455450 (option 2) or send a message to [email protected].
Data sheet
- For Use By
- Consumer Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Interior Walls
External Wall Cavities - Min. Application Temperature
- 5°C
- Suitable For Use On
- Masonry
- Suitable For Use On
- Beam and Block Floor System
- Usages
- Damp Proofing System
- Product Usage Type
- Damp Proof Course
- Product Range
- Zedex
- Colour Family
- Black
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Visqueen Zedex High Bond Damp Proof Course is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT