- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
An abrasion resistant, innovative 2-pack coating / putty for maintenance or repair of (mechanically) damaged coating areas.
- Solvent-free, 100% solids, CMR-free
- Easy-to-use packaging for difficult repair jobs
- Single layer coating
- Early water resistance and under water cure
- Surface tolerant - can be used on many substrates as manually prepared steel, stainless steel galvanization or aluminium, even on foreign coatings (except siloxane based coatings)
- Corrosion protection at 500 μm, similar to original in shop coating
- Diffusion resistant
- Plate like glass flakes increase coating strength
- Impact and abrasion resistant
- Very high colour retention
- If required overcoatable with 2-pack PU topcoats
Description
Sherwin Williams Repacor SW-1000 repair coating / putty with 100% volume solids. An abrasion resistant, innovative 2-pack coating / putty for maintenance or repair of (mechanically) damaged coating areas. Mechanically-and UV-resistant protective coating in easy-to-use-cartridge.
Quick Links - Click To Jump To Section:
- Recommended Use
- Technical Data
- Recommended Spreading Rate Per Coat
- Pot Life
- Average Drying Times
- Surface Preparation
- Mixing
- Application Conditions
- Application Equipment
- Recommended Systems
- Additional Notes
Recommended Use
Can be used as a corrosion protection putty for On and Offshore (wind turbines), for hydraulic engineering (lock gates, steel sheet piles etc.) or other elevated steel structures if a simple, high performance and durable repair coating is required.
Technical Data
| Volume Solids: | 100 ± 2% (ISO 3233-3) |
| Weight Solids: | 100 ± 2% |
| VOC: | 0 g/kg calculated from formulation to satisfy EC Solvent Emissions Directive (UK). |
| Colours: |
RAL 1023 (colour shade approved according to WSA-TR05), RAL 7035. Slight colour deviations are possible due to raw material characteristics. |
| Flash Point: | Base: > 200°C, Hardener: > 200°C. |
| Cleaner/Thinner: |
Thinner P (for cleaning). Thoroughly clean tools and equipment immediately after use. Do not thin Repacor™ SW-1000. |
| Pack Size: | A two component material supplied in a cartridge: Cartridge with 295 g, 12 cartridges per box, 60 boxes on pallet. |
| Mixing Ratio: | 2 parts base to 1 part hardener by volume. Self mixing due to 2-part cartridges with static mixer. |
| Density: | 1.5 kg/l (may vary with colours). |
| Shelf Life: | 2 years from date of manufacture, stored in originally sealed cartridges in a cool and dry environment. |
| Recommended Application Methods: | Putty, Brush |
Recommended Spreading Rate Per Coat
| Typical | ||
|---|---|---|
| Dry | 500 µm | 1000 µm |
| Wet | 500 µm | 1000 µm |
| Theoretical Consumption* |
0.750kg/m² 500l/m² |
1.500kg/m² 1.000l/m² |
| Theoretical Coverage* |
1.33m²/kg 2.00m²/l |
0.67m²/kg 1.00 m²/l |
* This figure makes no allowance for surface profile, uneven application, overspray or losses in containers and equipment.
Film thickness will vary depending on actual use and specification.
Pot Life
Pot Life (+ 20°C):
- 20 min
If cartridge is closed properly usable for approx. 30 days. Pot life is dependent on temperature and volume.
Average Drying Times
For 500 μm Dry Film Thickness:
| 20°C and 60% RH | |
|---|---|
| Dry to handle (Drying Stage 6*) | 1 hours |
| To recoat | 6 hours |
*ISO 9117
Final cure: 1 week at + 20°C, depending on film thickness and temperature. Material also cures under water.
These figures are given as a guide only. Factors such as air movement, film thickness and humidity must also be considered.
Surface Preparation
Ensure surfaces to be coated are clean, dry and free from all surface contamination such as oil, grease, dirt and corrosion products to achieve satisfactory adhesion.
Steel substrates shall be prepared by power tool grinded to P Ma – P St3 until a metallic sheen is arising or tensioned wire blast cleaning to P Sa 2½ according to ISO 8501-1 (ISO 12944-4). Average surface profile Rz ≥ 30 μm.
Mixing
By means of a static mixer, which is screwed on the cartridge prior to the application (see Application Equipment).
Application Conditions
Substrate temperature shall be above 0°C and at least 3°C above the dew point.
Material temperature shall be above + 10°C.
Relative air humidity shall be below 85%.
The surface must be dry and free from ice.
Application Equipment
Provide cartridge:
- Unscrew the cartridge, remove cap
- Screw on the static mixer
- Place the cartridge in the gun
Pressing on the cartridge shortly until uniform coloured material comes out (approx. 1 cm).
Start application by putty or brush.
When work is interrupted the static mixer can remain on the cartridge after the gun pressure has been relieved. In the static mixer material can remain up to 20 minutes at + 20 °C. If the material hardened in the static mixer, the static mixer must be replaced.
Recommended Systems
1 x Repacor™ SW-1000.
In case of deviating colour shades it can be overcoated with common 2-pack PUR topcoats as for example Acrolon 7300, Acrolon 1850. For external cathodic protection systems a minimum dry film thickness of 1000 μm is necessary.
Additional Notes
Drying times, curing times and pot life should be considered as a guide only.
Chemical resistance:
Resistant to industrial and marine environments, fresh-, brackish- and salt water, neutral salts, mineral oil and heating oil, grease and oils, detergents etc.
Temperature resistance:
Dry heat up to approx. + 100°C.
Increased humid ambient temperature and warm water up to approx. + 40°C.
For significant differential of temperature gradient please contact Rawlins Technical 0113 2455450 (option 2) or send a message to [email protected].
Numerical values quoted for physical data may vary slightly from batch to batch.
Product Details
11444-1015642
Data sheet
- For Use By
- Professional Use
- Interior / Exterior Use
- Exterior Use
- For Use On
- Steel (Manually Prepared)
Galvanising
Stainless Steel
Aluminium
Onshore Wind Turbines
Offshore Wind Turbines
Hydraulic Engineering
Lock Gates
Steel Sheet Piles
Elevated Steel Structures - Application Method
- Brush
Application Gun - Single, Two or Three Pack
- Two-Pack
- Pack Size
- 12 x 295g Cartridges
- Mixing Ratio
- 2:1 Base to Hardener by volume
- Dry to Handle (at 20°C)
- 1 hour (Drying Stage 6, ISO 9117)
- Dry to Recoat (at 20°C)
- 6 hours
- Fully Cured (at 20°C)
- 1 week, depending on film thickness
- Pot Life (at 20°C)
- 20 minutes (30 days if cartridge is closed properly)
- Coverage
- 2.00 m²/l (@ 500µm)
1.00 m²/l (@ 1000µm) - Min. Application Temperature
- 0°C
- Density
- 1.5KG
- Solids by Volume
- 100 ± 2% (ISO 3233-3)
- VOC
- 0g/l
- Shelf Life (from date of manufacture)
- 2 years
- UN Number (Activator)
- UN3082
- Consumption
- 0.500 l/m² (@ 500µm)
1.000 l/m² (@ 1000µm) - Solids by Weight
- 100 ± 2%
- Flashpoint
- +200°C
- Base Type
- Solvent Free
- Suitable For Use On
- Aluminium
- Suitable For Use On
- Stainless Steel
- Suitable For Use On
- Galvanising
- Suitable For Use On
- Hydraulic Engineering
- Suitable For Use On
- Onshore Wind Turbines
- Suitable For Use On
- Offshore Wind Turbines
- Suitable For Use On
- Steel (Manually Prepared)
- Suitable For Use On
- Lock Gates
- Suitable For Use On
- Steel Sheet Piles
- Application Method
- Brush
- Application Method
- Application Gun
- Manufacturer
- Sherwin-Williams
- Components
- 2K
- Usages
- Colour Retention
- Usages
- Metal Coating Repairs
- Product Usage Type
- Putty
- Chemical Resistance
- Grease and Oils
- Chemical Resistance
- Heating Oil
- Chemical Resistance
- Mineral Oil
- Chemical Resistance
- Detergents
- Chemical Resistance
- Industrial Environments
- Chemical Resistance
- Marine Environments
- Chemical Resistance
- Fresh Water
- Chemical Resistance
- Brackish Water
- Chemical Resistance
- Salt Water
- Chemical Resistance
- Neutral Salts
- Service Temperature
- 100°C (dry heat)
Increased humid ambient temperature and warm water up to approx. + 40°C
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Sherwin-Williams Repacor SW-1000 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage