Limited sizes, finishes and colours available. See options below for available quantities.
Jotun Solvalitt is a one component, physically drying silicone acrylic coating, heat resistant up to 600°C. Designed as a heat resistant coating suitable for insulated and non insulated surfaces, Solvalitt is recommended as a finish coat for insulated surfaces, in systems with suitable primers.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Jotun Solvalitt is a one component, physically drying silicone acrylic coating, heat resistant up to 600°C. Designed as a heat resistant coating suitable for insulated and non insulated surfaces, Solvalitt is recommended as a finish coat for insulated surfaces, in systems with suitable primers.
Can be used as primer, mid coat or finish coat in atmospheric environments. Suitable for properly prepared carbon steel, galvanised steel, stainless steel and aluminium substrates.
Due to variations in the thermal stability of pigments, slight colour changes can occur when the coating is heated. Note that such a colour change will not affect the performance of the coating.
| Property | Test/Standard | Description |
|---|---|---|
| Solids by volume | ISO 3233 | 43 ± 2 % |
| Gloss level (GU 60 °) | ISO 2813 | matt (0-35) |
| Flash point | ISO 3679 Method 1 | 26°C |
| Density | calculated | 1.3 kg/l |
| VOC-EU | IED (2010/75/EU) (theoretical) | 483 g/l |
The provided data is typical for factory produced products, subject to slight variation depending on colour.
Note: Heat resistant topcoats can be tinted in a range of colours. However, due to its pigmentation certain colours will appear less gloss and colour stable than others.
| Typical recommended specification range | |
|---|---|
| Dry film thickness | 20-30μm |
| Wet film thickness | 50-70μm |
| Theoretical spreading rate | 21-14m²/l |
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination.
For more in-depth surface preparation please refer to the Application Guide, downloadable here or from the attachments section above.
| Surface preparation summary table | ||
|---|---|---|
| Substrate | Minimum | Recommended |
| Carbon steel | Sa 2½ (ISO 8501-1) | Sa 2½ (ISO 8501-1) |
| Stainless steel | Cleanliness and surface profile corresponding to Sa 2½ (ISO 8501-1), Fine G (ISO 8503-2) | Cleanliness and surface profile corresponding to Sa 2½ (ISO 8501-1), Fine G (ISO 8503-2) |
| Aluminium | The surface shall be hand or machine abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to impart a scratch pattern to the surface. | Dry abrasive blast cleaning to SSPC-SP 13/NACE No. 6. |
| Galvanised steel | The surface shall be clean, dry and appear with a rough and dull profile. | Sweep blast-cleaning using non-metallic abrasive leaving a clean, rough and even pattern. |
| Coated surfaces | Clean, dry and undamaged compatible coating | Clean, dry and undamaged compatible coating |
For more in-depth application techniques please refer to the Application Guide, downloadable here or from the attachments section above.
Application methods
| The product can be applied by: | |
|---|---|
| Spray | Use air spray or airless spray. |
| Brush | Recommended for stripe coating and small areas. Care must be taken to achieve the specified dry film thickness. |
| Roller | May be used for small areas. Not recommended for first primer coat. Care must be taken to achieve the specified dry film thickness. |
Thinner/Cleaning solvent
Thinner:
Guiding data for airless spray
| Substrate temperature | 5°C | 10°C | 23°C | 40°C |
|---|---|---|---|---|
| Surface (touch) dry | 1 h | 45 min | 30 min | 15 min |
| Walk-on-dry | 4 h | 3 h | 2 h | 1.5 h |
| Dry to over coat, minimum | 8 h | 5 h | 4 h | 3 h |
For maximum overcoating intervals, refer to the Application Guide (AG) for this product.
Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the product.
Freshly applied Solvalitt film may have slightly reduced mechanical properties. This effect can however be overcome by heating the paint system to 200 °C for approx. 1 hour.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal tackiness.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks, imprints or other physical damage.
Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.
| Heat Resistance Table | ||
|---|---|---|
| Temperature | ||
| Continuous | Peak | |
| Dry, atmospheric | 600°C | - |
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures.
Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact Jotun/Rawlins Technical Support for specific system recommendation.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Be the first to ask a question about this product!
CLEARANCE - Jotun Solvalitt is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Jotun Thinner No. 7 is a paint thinner designed to improve the flow of a range of Jotun acrylic, vinyl and antifouling coatings. It can also be used as a cleaner of pumps and tools after and before painting.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...