Can you advise me what is the coverage of 1 bag of Sikal Floor Level. I am wanting this to be around 10mm thick. The room is approx 12ft x 15ft. I thought it would give the coverage; but cannot see this. Thanks Carol

The coverage rates for products are stated under the 'Product Details' tab on each product page - The coverage rate for Sikafloor Level 30 is 1.8kg/m²/mm. Based on 17m² (12x15ft) at a rate of 10mm thick you would require 306kg of material (13 x 25kg bags).

Can I use this on top of concrete as base for fire pit pizza oven,can it take direct flames. Thanks.

No, we would not recommend this.

I have a garage floor approximately 2.5m X 3.25m with a tamped finish very rough. It was painted about 12 years ago, now chipped in various places but appears sound. What products should I use to give a finish, smooth enough to move a heavy weight around on small caster wheels. Some idea of quantities would be helpful. Many thanks.

A product such as Sikafloor Level 30 or Rust-Oleum Speed Screed would be ideal for this application but all products of this nature that we offer will require the surface to be clean, dry and free of all contaminants e.g. dirt, oils, grease, existing coatings and surface treatments etc. before application.

Hi can you use this over tiles save taking them up

Idealy we would recommend to remove the tiles, however as long as they are well adhered to the concrete and are not broken up, you can abrade the surface of the tiles to remove the sheen, prime with Sikafloor 161 with a broadcast and go over with the Sikafloor Level 30 to required depth. You just need to take into consideration that the bond strength of the screed will only be as strong as the bond between the tiles and the concrete. Alternatively you could look at using Sikafloor 02 Primer followed by one of the other Sikafloor leveling compounds if the final floor finish is to be one of vinyl, lino, LVT, carpet tiles, etc.

Can I use Sikafloor 30 on a concrete garage floor as a finished surface ready for painting.

Yes, you will need to prime with Sikafloor 161 and fully broadcast with 0.3 - 0.8mm Sika Quartz Sand prior to the application of Sikafloor Level 30. Then, Sika would recommend 2 coats of Sikafloor 2540W or Sikafloor 264 N as a protective, finished floor coating.

Does Sikafloor Level 30 pump screed require priming prior application? Assuming it's going onto mechanically prepared (ground or shot-blasted) concrete base. Many thanks, Milda

It does, the type of priming will depend on the intended use. For normal intended use, e.g. foot traffic, prime with Sikafloor 01 Primer . For high loads e.g. forklift trucks etc, prime with Sikafloor 161 and fully broadcast with 0.3-0.8mm Sika Quartz Sand .

Sikafloor Level 30

Reference 413498

Brand Sika

Search ID SIK1664

Sikafloor Level 30 is a high performance, polymer modified, pumpable, cementitious, self-levelling and fast drying, cementitious screed for indoor or outdoor use at 4 - 30mm thickness. It meets the requirements of Class R3, according to EN 1504–3.

Low shrinkage
Fast setting and drying
Highly fluid
3-4 hours walk on time (+20°C)
Good surface appearance and hardness
Excellent freeze-thaw salt resistance
Casein and Formaldehyde free

Colour

Grey

Size

£56.75(incl. VAT)

£47.29(ex. VAT)

Quantity

Please choose your colour

Available for Delivery (See Delivery Options Below)

ColourPicker Explained

In general we sort colours for products into 2 main groups - ‘Ready Mixed’ and ‘Tinted’.
Tinted colours will always be more expensive than Ready Mixed colours as they need to be produced at the time of order using a tinting machine dispensing colourant into a base*.
During busy periods, this means that tinted colours could take longer, for example – a ready mixed colour ordered on a 3-5 day delivery might arrive within 3 days, however a tinted colour might take the full 5 days to arrive.

To find Ready Mixed colours, search "ready mixed" or select the Ready Mixed 'colour chart'. To see Tinted colours select a colour chart such as RAL, BS, NCS, etc. or search for a colour/hue to see available or related options.

To ensure fair pricing, we split colours into ‘Price Bands’ to group together similar priced colours. If you wish to search for the cheapest tinted colours, always select Price Band 1.

We make every effort to list all available colours, however we also offer a colour match service which can be accessed by contacting our Technical Team on 0113 245 5450 (option 2) or emailing [email protected]

*Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour

Colour reproduction of the Products on the Site is limited by the technology used to deliver web pages and by the colour representation of Customer’s own monitor and computer set-up. We have made every effort to display as accurately as possible the colours of our Products but we cannot guarantee that the colour shown on Customer’s monitor’s display will accurately reflect the colour of the Product on delivery. We recommend that Customer first purchases the smallest Product available or access an industry standard colour chart in person (and not digitally) to ensure that the colour is acceptable for its purposes.

6 questions about the product

Description

Sikafloor Level 30 is a polymer modified, pumpable, self-levelling, fast drying, cementitious screed for higher thickness interior or exterior floors meeting the requirements of Class R3, according to EN 1504–3.

Recommended Uses

Levelling or smoothing screeds and concrete floors at a thickness between 4 – 30mm in one working step
As a screed for industrial service conditions when sealed with a PU or EP resin topcoat
Medium to high load (heavy traffic and forklift pallet trucks with impact load)
Restoration work
Structural strengthening
Preserving or restoring passivity

For further details and application advice, please download the data sheets linked below.

Product Details

Reference 1664-229266

Data sheet

Manufacturer: Sika
Interior / Exterior Use: Interior & Exterior
For Use On: Concrete
Screed
Application Method: Trowel
Colour: Standard / Ready Mixed
Single, Two or Three Pack: Single
Product Certifications: EN 13813
Pack Size: 25KG
Coverage: 1.8kg / m² / mm
Touch Dry: 3 Hours
UN Number: N/A
Layer Thickness: 4-30mm
Drying time: Walk on hardness time at 20°C 3 hours
Base Type: Cement Based
Suitable For Use On: Concrete
Suitable For Use On: Screeds
Application Method: Trowel
Manufacturer: Sika
Components: 1K
Usages: Suitable for underfloor heating
Usages: Construction
Usages: Suitable to be painted
Usages: Self Levelling
Product Usage Type: Underlayments and Self-Levelling Floor Screeds
Product Range: Sikafloor
Product Attributes: Self Levelling
Product Attributes: Suitable To Be Painted
Product Attributes: Suitable For Underfloor Heating

Attachments

Download

Product Data Sheet

Download

Safety Data Sheet

Download

Declaration of Performance

Download

Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

Name ^*

Email ^*

Question ^*

^* Required fields

I have read and agree to the conditions of use (read)

Carol L Townsley on 2019-11-13 14:27:01	Question: Can you advise me what is the coverage of 1 bag of Sikal Floor Level. I am wanting this to be around 10mm thick. The room is approx 12ft x 15ft. I thought it would give the coverage; but cannot see this. Thanks Carol
	Answer from Rawlins’ Technical Team: The coverage rates for products are stated under the 'Product Details' tab on each product page - The coverage rate for Sikafloor Level 30 is 1.8kg/m²/mm. Based on 17m² (12x15ft) at a rate of 10mm thick you would require 306kg of material (13 x 25kg bags).

marcus on 2019-05-28 19:58:08	Question: Can I use this on top of concrete as base for fire pit pizza oven,can it take direct flames. Thanks.
	Answer from Rawlins’ Technical Team: No, we would not recommend this.

Chris Coffill on 2019-01-30 21:23:27	Question: I have a garage floor approximately 2.5m X 3.25m with a tamped finish very rough. It was painted about 12 years ago, now chipped in various places but appears sound. What products should I use to give a finish, smooth enough to move a heavy weight around on small caster wheels. Some idea of quantities would be helpful. Many thanks.
	Answer from Rawlins’ Technical Team: A product such as Sikafloor Level 30 or Rust-Oleum Speed Screed would be ideal for this application but all products of this nature that we offer will require the surface to be clean, dry and free of all contaminants e.g. dirt, oils, grease, existing coatings and surface treatments etc. before application.

Chris on 2019-01-17 13:41:30	Question: Hi can you use this over tiles save taking them up
	Answer from Rawlins’ Technical Team: Idealy we would recommend to remove the tiles, however as long as they are well adhered to the concrete and are not broken up, you can abrade the surface of the tiles to remove the sheen, prime with Sikafloor 161 with a broadcast and go over with the Sikafloor Level 30 to required depth. You just need to take into consideration that the bond strength of the screed will only be as strong as the bond between the tiles and the concrete. Alternatively you could look at using Sikafloor 02 Primer followed by one of the other Sikafloor leveling compounds if the final floor finish is to be one of vinyl, lino, LVT, carpet tiles, etc.

Eugene McArdle on 2018-09-16 16:46:50	Question: Can I use Sikafloor 30 on a concrete garage floor as a finished surface ready for painting.
	Answer from Rawlins’ Technical Team: Yes, you will need to prime with Sikafloor 161 and fully broadcast with 0.3 - 0.8mm Sika Quartz Sand prior to the application of Sikafloor Level 30. Then, Sika would recommend 2 coats of Sikafloor 2540W or Sikafloor 264 N as a protective, finished floor coating.

Milda on 2018-06-13 15:24:40	Question: Does Sikafloor Level 30 pump screed require priming prior application? Assuming it's going onto mechanically prepared (ground or shot-blasted) concrete base. Many thanks, Milda
	Answer from Rawlins’ Technical Team: It does, the type of priming will depend on the intended use. For normal intended use, e.g. foot traffic, prime with Sikafloor 01 Primer. For high loads e.g. forklift trucks etc, prime with Sikafloor 161 and fully broadcast with 0.3-0.8mm Sika Quartz Sand.

IMPORTANT SHIPPING & DELIVERY INFORMATION

Sikafloor Level 30 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT

Follow us on:

Sikafloor Level 30

Sikafloor Level 30

Recommended Uses

Data sheet

Questions

Question about the product

IMPORTANT SHIPPING & DELIVERY INFORMATION