- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Sherwin-Williams Macropoxy C401 (formerly known as Epigrip C401) is a high solids 2-pack epoxy, pigmented with micaceous iron oxide for use as an undercoat in conjunction with Sherwin-Williams Macropoxy high performance primers. Provides corrosion protection in a single coat, Network Rail approved.
Sherwin-Williams Macropoxy C401 (formerly known as Epigrip C401) is a high solids 2-pack epoxy, pigmented with micaceous iron oxide for use as an undercoat in conjunction with Sherwin-Williams Macropoxy high performance primers. Provides corrosion protection in a single coat, Network Rail approved.
Endorsements
- Network Rail Item No’s 7.2.2 and 7.1.7
Recommended Primers & Topcoats
- Macropoxy C425V2
- Macropoxy C400V3
- Zinc Clad J984
- Macropoxy C402V2
Where a high degree of gloss and colour retention is re- quired, overcoat with Acrolon C137V2, Acrolon C237, Acolon 1850 and Acrolon 7300 within 7 days at a minimum d.f.t. of 50 microns or in the case of Acrolon C750V2 overcoat within 4 days.
These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature. For overcoating outside the above parameters and with alkyd systems, consult Technical Team for advice.
Application Conditions & Overcoating
Epoxy paints should preferably be applied at temperatures in excess of 10°C. Relative humidity should not exceed 90% and in these conditions good ventilation is essential. Substrate temperature shall be at least 3°C above the dew point and always above 0°C
At application temperatures below 10°C, drying and curing times will be significantly extended, and spraying characteristics may be impaired. Application at ambient air temperatures below 5°C is not recommended.
In order to achieve optimum water and chemical resistance, temperature needs to be maintained above 10°C during curing.
If it is desired to overcoat outside the times stated on the data sheet, please seek advice of Technical Team.
Additional Notes
Drying times, curing times and pot life should be considered as a guide only.
The curing reaction of epoxies commences immediately the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.
Epoxy Coatings - Colour Stability:
Variable colour stability is a feature of epoxy materials which tend to yellow and darken with age whether used on internal or external areas. Therefore any areas touched-up and repaired with the same colour at a later date may be obvious due to this colour change.
When epoxy materials are exposed to ultra-violet light a sur- face chalking effect will develop. This phenomenon results in loss of gloss and a fine powder coating at the surface which may give rise to colour variation depending on the aspect of the steelwork. This effect in no way detracts from the perfor- mance of the system.
Epoxy Coatings - Tropical Use
Epoxy paints at the time of mixing should not exceed a temperature of 35°C. At this temperature the pot life will be approximately halved. Use of these products outside of the pot life may result in inferior adhesion properties even if the materials appear fit for application. Thinning the mixed product will not alleviate this problem.
The maximum air and substrate temperature for application is 50°C providing conditions allow satisfactory application and film formation. If the air and substrate temperatures exceed 50°C and epoxy coatings are applied under these conditions, paint film defects such as dry spray, bubbling and pinholing etc. can occur within the coating.
Numerical values quoted for physical data may vary slightly from batch to batch.
Data sheet
- Manufacturer
- Sherwin-Williams
- For Use By
- Industrial Use
- Water / Solvent Based
- Solvent
- For Use On
- Steel
- Application Method
- Airless Spray, Spray, Brush, Roller
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5L, 20L
- Coverage
- 7.5m² per litre
- Touch Dry
- 1.5 Hours
- UN Number (Activator)
- UN3470
- UN Number (Base)
- UN1263
- Base Type
- Solvent-Based
- Base Type
- Epoxy
- Suitable For Use On
- Steel
- Suitable For Use On
- Primed Surfaces
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Usages
- High Solids
- Usages
- Atmospheric
- Usages
- MIO
- Usages
- Undercoat
- Product Usage Type
- Undercoat
- Product Range
- Macropoxy
- Colour Family
- Grey
- Dry to Recoat (@ 20-25°C)
- 4 hours
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Sherwin-Williams Macropoxy C401 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT