- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Sherwin-Williams Epo-Phen FF coating is a flake-filled (MIO) amine cured epoxy phenolic novolac formulated for use under thermal insulation at elevated or cryogenic temperatures and for immersion service in water and hydrocarbons such as gasoline, fuel oil, and diesel fuel.
- Temperature resistant to 218°C (425°F), constant; 232°C (450°F) intermittent (dry service)
- Self priming
- Chemical resistant
- Please note: Also available in a 20L pack size which is made to order subject to a minimum order quantity of 200L and an extended lead time of 28 days - please see Sherwin-Williams Epo-Phen FF - Special Order
Description
Sherwin-Williams Epo-Phen FF coating is a flake-filled (MIO) amine cured epoxy phenolic novolac formulated for use under thermal insulation at elevated or cryogenic temperatures and for immersion service in water and hydrocarbons such as gasoline, fuel oil, and diesel fuel.
Features & Benefits
- Temperature resistant to 218°C (425°F), constant; 232°C (450°F) intermittent (dry service)
- Self priming
- Chemical resistant
The micaceous iron oxide (MIO) provides:
- High temperature resistance
- Film reinforcement
- One coat, high build application
- Improved edge protection
Recommended Uses
- Steel and stainless steel tanks and piping under insulation
- Non-insulated structural steel and piping subjected to chemical or abrasion attack
- Use in areas subject to wet/dry cycling up to 149°C (300°F)
- Use in areas where temperature resistance up to 232°C (450°F) is required (dry service)
- Acceptable for use in immersion service at elevated temperatures for fresh water and distilled water 99°C (210°F)
- Suitable for storage of gasoline, fuel oil, diesel fuel, and other similar hydrocarbon cargos
- Not qualified for potable water immersion
- Water and wastewater facilities
- Wind tower gearbox lining
Performance Tips
Stripe coat crevices, welds, and sharp angles to prevent early failure in these areas.
When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. If necessary, cross spray at a right angle.
Spreading rates are calculated on volume solids and do not include an application loss factor due to surface profile, roughness or porosity of the surface, skill and technique of the applicator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic conditions, and excessive film build.
For Immersion Service: (if required) Holiday test in accordance with ASTM D5162 for steel, or ASTM D4787 for concrete.
Excessive reduction of material can affect film build, appearance, and adhesion.
Do not mix previously catalyzed material with new.
Do not apply the material beyond recommended pot life. In order to avoid blockage of spray equipment, clean equipment before use or before periods of extended downtime with Reducer #15.
Temperatures above 25°C (77°F) will shorten the pot life.
Do not apply over 225 microns (9.0 mils) total dft when used in service above 149°C (300°F).
Not recommended for potable water immersion.
Acceptable for insulation to be applied over the coating, after the coating has reached it's dry to touch time.
Refer to Product Information sheet for additional performance characteristics and properties.
Product Details
2147-276854
Data sheet
- Manufacturer
- Sherwin-Williams
- For Use By
- Industrial Use
- For Use On
- Steel
- Application Method
- Brush, Roller, Spray
- Sheen
- Semi Gloss
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5L
- Application
- Brush, Roller, Spray
- Coverage
- 3.0 - 3.9m² per litre
- Solids by Volume
- 70% ± 2%
- Shelf Life (from date of manufacture)
- 24 months, unopened Store indoors at 4.5°C (40°F) to 38°C (100°F)
- Touch Dry
- 3 hours
- UN Number (Activator)
- UN3066
- UN Number (Base)
- UN1263
- Fully Cured
- 7 days
- Solids by Weight
- 85% ± 2%
- Base Type
- Solvent-Based Epoxy
- Suitable For Use On
- Steel
- Finish
- Semi-Gloss
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Tank Lining
- Product Range
- Epo-Phen
- Colour Family
- Grey
Questions
Question about the product
Karey Smith
on
2024-05-29 20:47:16
| Question:
Sherwin-Williams Epo-Phen FF, when applying this product and leaving in the sun for a period of time. How long can you leave out in the sun/UV before causing damage to the coating? |
Answer from Rawlins’ Technical Team:
This product is designed for application to lining tanks, and shouldn't suffer degradation if exposed to UV, however it will start to chalk as a result of being an epoxy based product. If the intended use is for a lining system, chalking must be removed before it comes into service. | |
|
NEP services
on
2020-06-05 08:23:27
| Question:
Good morning, is this product two pack, if so do you gert both components when ordering the 20L option. |
Answer from Rawlins’ Technical Team:
Yes this is a two pack product and both components are including product listing and pricing. | |
|
Ray Manley
on
2018-11-14 20:41:10
| Question:
Is this product rated for aluminum materials? tubing/piping/ angle etc. |
Answer from Rawlins’ Technical Team:
Sherwin-Williams Epo-Phen FF can indeed be applied to aluminium, you can download the product data sheets from the product page for further details. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Sherwin-Williams Epo-Phen FF is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT