Follow us on:

Sherwin-Williams Epidek M153
Sherwin-Williams Epidek M153

Sherwin-Williams Epidek M153

M153
SHE2174

Sherwin-Williams M153 is an aggregate dressed, ultra heavy duty, hard wearing, coal tar free, solvent-less epoxy anti-slip deck coating. It is used for the treatment of deck surfaces subject to the most extreme of operational conditions requiring a high degree of impact and abrasion resistance, where a high level of anti-slip properties need to be retained under conditions of severe crude oil and hydrocarbon contamination.

  • Epoxy anti-slip deck coating
  • For the treatment of deck surfaces subject to the most extreme of operational conditions
  • Complies with NORSOK M501 (Rev.5) System 4 
  • Two component
  • Please note: Also available in Light Grey and Bright Yellow subject to a minimum order quantity of 200L and an extended lead time of up to 14 working days - Please see Sherwin-Williams M153 - Special Colours

Please note: Colours shown are for illustrative purposes only

Colour
Item
Finish
Add-Ons
£367.37(incl. VAT)
£306.14(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

Sherwin-Williams M153 is an aggregate dressed, ultra heavy duty, hard wearing, coal tar free, solvent-less epoxy anti-slip deck coating. It is used for the treatment of deck surfaces subject to the most extreme of operational conditions requiring a high degree of impact and abrasion resistance, and where a high level of anti-slip properties need to be retained under conditions of severe crude oil and hydrocarbon contamination. 

Endorsements

Complies with NORSOK M501 (Rev.5) System 4 

Recommended Primers/Topcoats

  • Macropoxy C425V2 Zinc Phosphate Primer/Buildcoat
  • Macropoxy L425 Zinc Phosphate Primer
  • Macropoxy M262 Hi-Build Finish 

Application Conditions & Overcoating

It is preferred that whenever practical Epidek M153 should be applied directly on to blast cleaned steel to Sa21⁄2. M153 may be applied over an approved high build epoxy primer.

If applied over Macropoxy Blast Primer the primer thickness must be carefully controlled. The target DFT is 25μm but the maximum DFT applied must not exceed 40μm. If a high build primer is required please use one of those recommended on the front of this data sheet.

This material should preferably be applied at temperatures in excess of 10°C. In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3°C above the dew point and always above 0°C.

At application temperatures below 10°C, drying and curing times will be significantly extended, and spraying characteristics may be impaired.

Application at ambient air temperatures below 5°C is not recommended.
If it is desired to overcoat outside the times stated on the data sheet, please seek advice of Technical Team.

Packaging

A two component package comprising Component ‘A’ and ‘B’

Component A (20 litre pail); Containing 12.6 litres base screed unit comprising epoxy resin base, curing agent and fine silica grit.

Component B (nylon sack); Containing 25kg calcined bauxite aggregate (see below).

Pack Size: 12.6 litre unit when mixed
Mixing Ratio: 1.54 parts base to 1 part additive by volume plus silica grit
Weight: 1.84 kg/litre (may vary with shade).
Shelf Life: 2 years from date of manufacture or ‘Use By’ date where specified.

Additional Notes

Drying times, curing times and pot life should be considered as a guide only.

The curing reaction of epoxies commences immediately the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.

Calcined Bauxite Aggregate

Four sizes of aggregate are available depending on degree of anti-slip properties required and end use:-
1. Light Aggregate (0.85 - 1.70mm )
2. Medium Aggregate (1.40 - 2.00mm )
3. Heavy Aggregate (1.40 - 2.80mm)
4. Road Aggregate (3.00 - 5.00mm)

N.B. Consumption of aggregate will depending upon screed thickness, efficiency of excess aggregate recovery and recycling. For guidance on quantities of aggregate consult sheet entitled Epigrip M153 Supplementary Information.

Overcoating

If it is felt desirable to overcoat the surface of Epidek M153 Heavy Duty Deck Coating or to mark surfaces with a different colour this may be achieved by the application of a coat of Macropoxy M262 Hi-Build Finish.

Numerical values quoted for physical data may vary slightly from batch to batch.

Product Details
2174-899849

Data sheet

For Use By
Industrial Use
Application Method
Trowel
Sheen
Mid Sheen
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Two-Pack
Product Certifications
NORSOK M501 (Rev.5) System 4
Pack Size
12.6L
Coverage
0.32m² per litre
Touch Dry
5 Hours
UN Number (Activator)
UN3469
UN Number (Base)
UN1263
Base Type
Solvent-less Epoxy
Finish
Mid Sheen
Application Method
Trowel
Product Usage Type
Topcoat
Product Range
Epidek
Colour Family
Grey
Colour Family
Green
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

Sherwin-Williams Epidek M153 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


COVERAGE CALCULATOR
Units
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

You might also like
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery