Follow us on:

Sherwin-Williams M330 - Available at Rawlins Paints & Coatings

Sherwin-Williams Macropoxy M330

M330
SHE2179

Sherwin-Williams Macropoxy M330 (formerly known as Epigrip M330) is a 2-pack epoxy sealercoat for use over zinc silicate and other types of zinc rich primers. It is also used as a blast primer for use over stainless steel.

  • Please note: This product is made to order subject to a minimum order quantity of 150L and an extended lead time of 14 working days
Colour
Size
Finish
£109.28(incl. VAT)
£91.07(ex. VAT)
Quantity
Please choose your colour
This Combination may be Subject to Extended Lead Times

The minimum purchase order quantity for the product is 30.

No queries yet, leave the first!
Description

Sherwin-Williams Macropoxy M330 (formerly known as M330) is a 2-pack epoxy sealercoat for use over zinc silicate and other types of zinc rich primers. It is also used as a blast primer for use over stainless steel.

Recommended Primers & Topcoats

  • Zinc Clad J984 Zinc Rich Primer
  • Dox-Anode D5V2

Indefinitely overcoatable with epoxy systems provided the surfaces to be coated have been suitably cleaned. Where a high degree of gloss and colour retention is required, overcoat with Acrolon C137V2, Acrolon C237 within 7 days at a minimum dft of 50 microns or in the case of Accrolon C750V2 overcoat within 4 days. These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature.

For overcoating with alkyd systems consult Technical Team for advice. 

Application Conditions & Overcoating

Epoxy paints should preferably be applied at temperatures in excess of 10oC. In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3oC above the dew point and always above 0°C.

At application temperatures below 10°C, drying and curing times will be significantly extended, and spraying characteristics may be impaired.

Application at ambient air temperatures below 5°C is not recommended.

In order to achieve optimum water and chemical resistance, temperature needs to be maintained above 10oC during curing.

If it is desired to overcoat outside the times stated on the data sheet, please seek advice from Technical Team.

Additional Notes

Drying times, curing times and pot life should be considered as a guide only.

The curing reaction of epoxies commences immediately
the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.

When M330 is used as a tie-coat or sealer coat over inorganic zinc silicate, the zinc silicate must be left for a minimum of 16 hours at 15°C and then checked for cure. Prior to overcoating, the inorganic zinc silicate primer must be fully cured.

Care must be taken to ensure that Macropoxy M330 is not over-applied on to the zinc silicate otherwise there is a possibility of pinholing occurring. 

Epoxy Coatings - Tropical Use

Epoxy paints at the time of mixing should not exceed a temperature of 35°C. At this temperature the pot life will be approximately halved. Use of these products outside of the pot life may result in inferior adhesion properties even if the materials appear fit for application. Thinning the mixed product will not alleviate this problem.

The maximum air and substrate temperature for application is 50°C providing conditions allow satisfactory application and film formation. If the air and substrate temperatures exceed 50°C and epoxy coatings are applied under these conditions, paint film defects such as dry spray, bubbling and pinholing etc. can occur within the coating.

Numerical values quoted for physical data may vary slightly from batch to batch. 

Product Details
2179-276039

Data sheet

For Use By
Industrial Use
For Use On
Steel
Application Method
Spray
Sheen
Matt
Colour
Fully Tintable
Single, Two or Three Pack
Two-Pack
Pack Size
5L
Application
Spray
Coverage
18.8m² per litre
Touch Dry
10 minutes
UN Number (Activator)
UN3469
UN Number (Base)
UN1263
Base Type
Solvent-Based
Base Type
Epoxy
Suitable For Use On
Stainless Steel
Suitable For Use On
Zinc Silicate Primers
Suitable For Use On
Zinc Rich Primers
Finish
Matt
Application Method
Spray
Usages
Atmospheric
Usages
Tie Coat
Usages
Intermediate
Product Usage Type
Tie Coat
Product Usage Type
Intermediate
Product Range
Macropoxy
Colour Family
Red
Dry to Recoat (@ 20-25°C)
4 hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

Sherwin-Williams Macropoxy M330 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


COVERAGE CALCULATOR
Units
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

You might also like
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery