- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
- Two-component, water-based impregnation agent and primer available in a yellowish clear finish.
- Suitable for use on mineral substrates, including concrete, cement screed, anhydrite screed, and magnesite screed.
- Excellent adhesion properties with high water vapour diffusion capability.
- Ideal for priming in Remmers water vapour diffusion (WDD) systems.
- Certified to EN 13813:2002 with bond strength ≥ B 1.5 and wear resistance ≤ AR 0.5.
- For professional use only.
Description
High-Performance Water-Based Impregnation Agent and Primer
Designed for professional applications on mineral surfaces. This two-component system offers excellent adhesion and water vapour diffusion properties, making it ideal for use in Remmers water vapour diffusion (WDD) systems. The product ensures strong substrate penetration, reinforcing surface integrity while maintaining breathability.
Where It Can Be Used
Suitable for use on a wide range of mineral surfaces, including:
- Concrete
- Cement screeds
- Anhydrite screeds
- Magnesite screeds
The product is specifically designed for applications where high adhesion and moisture control are required.
Application Instructions
The substrate must be clean, stable, and free from contaminants such as dust, grease, and loose particles. It should have a minimum tensile strength of 1.5 N/mm² and a compressive strength of at least 25 N/mm².
Before application, ensure that moisture content does not exceed the following levels:
- Concrete: Max. 6% moisture
- Cement screed: Max. 6% moisture
- Anhydrite screed: Max. 0.3% moisture
- Magnesite screed: 2-4% moisture
Mix component A and B in a 75:25 ratio by weight and stir thoroughly for at least 3 minutes. Apply using an epoxy roller, rubber scraper, or brush, ensuring full penetration into the substrate. The working time is approximately 60 minutes at 20°C.
For high-absorbency surfaces, dilute with up to 20% water before application.
Drying & Curing Time
- Foot traffic: 1 day
- Mechanical loading: 3 days
- Full chemical resistance: 7 days
Ensure adequate ventilation to facilitate drying and avoid moisture contact during curing.
Limitations & Restrictions
Not suitable for use on non-mineral substrates or surfaces exposed to UV light. Epoxy resins may develop slight discoloration over time. Abrasive mechanical loads can leave wear marks.
For optimal results, apply at temperatures between +8°C and +30°C with a relative humidity below 80%. The substrate temperature must be at least 3°C above the dew point to prevent condensation.
Compatible Products
Recommended for use with:
- Epoxy BS 4000 (6320)
- Epoxy BS 3000 M (6370)
- Epoxy BS 3000 SG (6380)
Refer to the respective technical data sheets for further details.
Health & Safety
The product contains epoxy resins and may cause skin irritation, eye damage, and allergic skin reactions. It is classified as hazardous under GB CLP regulations.
- UN Number: UN3082 (Component B)
- Signal Word: Danger
- Hazard Statements: H315, H317, H318, H319, H411
- Use protective gloves, eye protection, and respiratory equipment where necessary.
Dispose of in accordance with local regulations. Always refer to the full safety data sheet before use.
Product Details
2619-645654
Data sheet
- Manufacturer
- Remmers
- For Use On
- Concrete, Cement
- Application Method
- Roller
- Sheen
- Matt
- Colour
- Clear
- VOC Levels
- Low (50-149 g/l)
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 25KG
- Parts
- Two
- Base Type
- Epoxy
- Suitable Substrates
- Concrete, cement
- Touch Dry (at 20°C)
- 24 hrs
- Dry to Recoat (at 20°C)
- 12 hrs
- Pot Life (at 20°C)
- 60 mins
- Coverage
- 0.20 - 0.50 kg/m² binder
- Recommended Thinner/Cleaner
- Water
- Max. Application Temperature
- 30 °C
- Min. Application Temperature
- 8 °C
- Density
- 1.05 g/cm³
- UN Number
- UN3082
- Base Type
- Water-Based
- Suitable For Use On
- Concrete
- Suitable For Use On
- Cement
- Finish
- Matt
- Application Method
- Roller
- Components
- 2K
- Product Usage Type
- Adhesion Primer
- Product Range
- Epoxy BS
- Colour Family
- Clear
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Remmers Epoxy BS 2000 Transparent is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
