- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A decorative epoxy resin floor screed incorporating multi-coloured aggregates, designed to produce a hard wearing, attractive, impervious sealed surface, sealed with clear resins to provide a matt or gloss finish.
- Formerly known as Resuscreed QS and Decora MS
- Decorative, hard wearing and durable
- Ease of application - low odour
- Good slip resistant properties
- Excellent abrasion and impact resistance - good chemical resistance
- See below for system information and application instructions.
- Recommended uses includes buildings where a seamless decorative finish is required, pharmaceutical areas, animal compounds and veterinary areas, toilets and reception areas, healthcare industry, production areas, prisons and police cells, industrial workshops
Note that all colours have minimum order quantities of 40 units and lead times of 14-21 working days due to being made to order
Resuflor Q Screed (formerly known as Resuscreed QS and Decora MS) is a decorative epoxy resin floor screed incorporating multi-coloured aggregates, designed to produce a hard wearing, attractive, impervious sealed surface. The system is applied at 4mm minimum thickness and then sealed with clear resins to provide a matt or gloss finish. See below for system information and application instructions.
For more aggregate see RSL Resuscreed QS Aggregates only.
Features & Benefits
- Decorative
- Hard wearing & durable
- Ease of application
- Low odour
- Good slip resistant properties
- Excellent abrasion and impact resistance
- Good chemical resistance
- Recommended uses:
- Buildings where a seamless decorative finish is required
- Pharmaceutical areas
- Animal compounds and veterinary areas
- Toilets and reception areas
- Healthcare industry
- Production areas
- Prisons and police cells
- Industrial workshops
Product Information
Product Information | |
---|---|
System Thickness (Recommended) | 4-6mm |
Solids Content by Weight | 100% |
Pack Make Up | 1 x Base 1 x Hardener 1 x Resuscreed QS Aggregate |
Shelf Life | 36 months (Base, Hardener & Aggregate) |
Storage | Keep out of direct sunlight. Store in a dry place, between 15°C- 30°C |
Application Information (at 20°C) | |
Coverage Rate (Theoretical) | 28kg will cover 3.5m² at 4mm thickness |
*Coverage rate is calculated based on a sealed and smooth surface and may vary based on the substrate roughness and other conditions. | |
Pot Life | 30 Minutes |
Recoating Intervals | 8 Hours |
Light Traffic | 24 hours |
Full Traffic | 72 hours |
Full Chemical Cure | 7 days |
Technical Information | |
Category Guide | FerFA Category 6 |
Slip Resistance | Dry >55 |
Method BS7976 pt1-3 2002 | Wet - Please consult Sherwin-Williams/Rawlins Paints Technical |
The slip resistance of a floor surface can vary as a result of the installation process, conditions at the time of application and subsequent traffic. Inappropriate cleaning or maintenance can adversely affect the performance. For further advice on potential wet areas please consult Sherwin-Williams/Rawlins Technical | |
Abrasion Resistance (Method BS EN 13892-4:2002) | AR0.5 |
Temperature Resistance | Tolerant of temperatures up to 60°C |
Chemical Resistance | Good chemical resistance - Consult Sherwin-Williams/Rawlins Technical |
VOC | 34 g/l - Calculation based on a full mixed unit |
Life Expectancy | Up to 6 years - subject to industrial traffic. Sherwin-Williams terms and conditions will apply |
Products required for this system
- Primer : Resuprime ST or use Resuprime MVT on damp surfaces where required
- System : Resuflor Q Screed at required thickness
- Surface Seal : Resuflor GC-UVR followed by Resuflor HB Clear and an optional coat of Resupen WB Clear Matt where a matt finish is required.
Preparation
New Concrete Floors:
New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.
Existing Concrete Floors:
Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuflor Patch.
Existing Floors (previously coated)
All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. if the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.
Timber Floors
Must be clean, sound, dry . Old clear varnish/topcoat must be removed/sanded prior to application, as it may affect the intercoat adhesion with Resuflor Q Screed.
Priming
Open and porous substrates may require priming with Resuseal WB, also Resuprime ST may be used as primer on dry substrates only with less than 75% ERH reading. Where the Relative Humidity of a substrate exceeds 75% ERH Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.
The number of coats to be applied is chosen in accordance with the following table:
ERH% | Required Coating Thickness |
---|---|
75-85 | 1 coat of Resuprime MVT at 200 microns per coat |
85-92 | 2 coats of Resuprime MVT at 200 microns per coat |
92-97 | 3 coats of Resuprime MVT at 200 microns per coat |
For further information please refer to recommended individual product data sheets.
Application
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period , as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing:
Mix the entire contents of base with the hardener, if using a separate mixing vessel then ensure the entire contents of the base and hardener are emptied out of the buckets supplied. Pour the combined base and hardener into a rotary drum mixer and add the aggregate component steadily, until a homogeneous mix of the three components is achieved. The mixed unit should be applied immediately after mixing. Apply to pre-primed areas and level between battens as necessary with a steel float, alternatively a sledge can be used set at the required thickness.
Resuflor Q Screed should be worked with a trowel or float to achieve a dense, compacted finish. This is best achieved by the application of smooth even pressure in one direction, gradually increasing the pressure as the material compacts and beds down. Over-working the material will draw fines to the surface which may result in resin-rich spots, colour and finish variations.
The surface should be protected from temperatures of less than 10°C and moisture in the early stages of cure.
Coving can be formed in advance of the floor laying process, and or at the same time. Where laid in advance a join line may be visible between the cove and floor.
At 100mm nominal height, one 28 kg unit of Resuflor Q Screed will typically form up to 10 linear meters of coving which must be applied onto a wet primer coat of Resuprime MVT to achieve maximum adhesion.
Seal Coats:
Resuflor Q Screed is normally sealed with the application, by squeegee, of one coat of Resuflor GC-UVR at a rate of 3-4m²/kg. This would be followed by a coat of Resuflor HB Clear at a rate of 3-5m²/kg. The optional Resupen WB Clear Matt is applied at a rate of 10m²/L to provide a flat matt finish. Please refer to individual product datasheets for coverage rates, recoat and traffic times.
Data sheet
- Manufacturer
- RSL
- For Use By
- Industrial Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Concrete Floors
Timber Floors - Application Method
- Trowel
Float - Single, Two or Three Pack
- Three-Pack
- Parts
- 3
- Base Type
- -
- Minimum Applied Thickness
- 4-6mm
- Solvent
- Epoxy
- Mixing Ratio
- -
- Key Features
- Produce a hard wearing, attractive, impervious sealed surface.
- Fully Cured (at 20°C)
- 7 days
- Pot Life (at 20°C)
- 30 Minutes
- Coverage
- 28kg will cover 3.5m² at 4mm thickness
- Unit Contents
- 1 x Base 1 x Hardener 1 x Resuscreed QS Aggregate
- Compatible Primers
- Resuprime ST or use Resuprime MVT on damp surfaces where required
- Compatible Topcoats
- Resuflor GC-UVR followed by Resuflor HB Clear and an optional coat of Resupen WB Clear Matt where a matt finish is required.
- Min. Application Temperature
- 15°C
- Heat Resistance (up-to)
- 60°C
- VOC
- 34 g/l - Calculation based on a full mixed unit
- Shelf Life (from date of manufacture)
- 36 months (Base, Hardener & Aggregate)
- UN Number (Activator)
- UN3066
- UN Number (Base)
- UN3082
- Resistance to chemicals
- Good chemical resistance
- Dry for Light Traffic (at 20°C)
- 24 hours
- Dry for Full Traffic (at 20°C)
- 72 hours
- Suitable For Use On
- Concrete Floors
- Suitable For Use On
- Timber Floors
- Application Method
- Trowel
- Application Method
- Float
- Components
- 3K
- Product Usage Type
- Coloured Screed
- Product Range
- Resuflor
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Orange
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Average Application Thickness
- 4-6mm
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
RSL Resuflor Q Screed is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
RSL Resupen WB - Standard Readily Available Colours
Extremely durable polyurethane finish for concrete, plaster and wood that produces a resilient coating on Sherwin-Williams wall and flooring systems. It is available in clear, colour, matt and satin finish. For more colours, see RSL Resupen WB - Special Colours. Chemical resistant and UV stable. Good abrasion and impact resistance....
RSL Resuprime ST Bonding & Priming Coat
2-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces. Versatile for many types of application. Excellent adhesive properties. Easy to apply. Can be used as a tack coat for screeds. No unpleasant or harmful odours. Formerly known as Resuprime.
RSL Resuflor GC-UVR
RSL Resuflor GC-UVR (formerly known as Resucoat GC and R.S Screed Seal) is a two-pack epoxy resin surface coating for use with other RSL and Sherwin-Williams products, filling any voids, pockets or interstices exposed in the surface. Enhances chemical resistance Prevents water spillage Improves cleanability Hygienic No shrinkage on...
RSL Resuprime MVT
A faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Easy application Use on substrates with hygrometer readings <97% Solvent-free...
RSL Resutack EP
We no longer stock this product, but can recommend RSL Resuprime MVT as a great alternative.
RSL Resuflor HB Clear
2-pack, high solids, high-build epoxy coating for application as a chemical resistant heavy duty floor coating, used as a clear sealer for decorative flooring systems such as RSL Resuflor Q Screed, producing a seamless, hard wearing, hygienic floor finish. Recommended uses include in food processing and beverage areas, chemical plant rooms,...
RSL Resuflor Q Screed Aggregates Only - Multi Coloured
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. RSL Resuflor Q Screed Aggregates Only (Formerly Resuscreed QS Aggregates Only), for use with RSL Resuflor Q Screed (formerly known as Resuscreed...