- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
RSL Resuflor GC-UVR (formerly known as Resucoat GC and R.S Screed Seal) is a two-pack epoxy resin surface coating for use with other RSL and Sherwin-Williams products, filling any voids, pockets or interstices exposed in the surface.
- Enhances chemical resistance
- Prevents water spillage
- Improves cleanability
- Hygienic
- No shrinkage on curing
- Can be used decoratively
- Colour stability
For optimum results, RSL Resuflor GC-UVR (formerly known as Resucoat GC and R.S Screed Seal) should be used with Resuscreed 45, Resuscreed 55, and Resuscreed QS - all Resin Surfaces Limited products.
Recommended Uses
- Food and beverage sites
- Factories
- Warehouses
- Engineering environments
- Garages/Showrooms
- Aviation hangars
Preparation
The surface to be treated with Resuflor GC-UVR must be clean, sound, dry and fully cured. Rates of coverage will be affected by the particle size and the density of packing achieved during the application of the screed. Open textures will reduce rates of coverage significantly.
Application
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance of the system. Surface temperature must be above 10°C.
Where possible it is recommended that the application area is heated to a minimum temperature of 15°C to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing: Pre-mix the base component to a uniform consistency then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used, mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two minutes or until the two components have fully combined.
Resuflor GC-UVR is highly thixotropic, careful and thorough mixing is required. For trowel and squeegee application, de-nibbing of the surface by steel trowel is recommended prior to application.
Resuflor GC-UVR should be applied within 48 hrs of the application of the screed system. Apply to the clean surface with a polypropylene squeegee. Ensure that the Resuflor GC-UVR is forced into the surface of the resin screed and pull down any excess to leave a thin coating. Finally, roller off to achieve an even film finish. Resuflor GC-UVR does not tend to flow, therefore it is important to ensure that the finish is to an acceptable standard whilst wet.
When Resuflor GC-UVR is being used on coloured systems, after an overnight cure apply a coat of Resuflor HB to provide a wearing finish.
When Resuflor GC-UVR is being used on decorative systems, after an overnight cure apply a coat of Resuflor HB Clear to provide a wearing finish.
Data sheet
- Manufacturer
- RSL
- For Use By
- Industrial Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Concrete Floors
- Application Method
- Squeegee
- Sheen
- Smooth Gloss
- Colour
- Clear
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5KG
- Application
- Squeegee
- Coverage
- 5kg will cover 12m sq. @ 360 microns DFT.
- Touch Dry
- 8-10 Hours
- UN Number (Activator)
- UN3066
- UN Number (Base)
- UN3082
- Suitable For Use On
- Concrete Floors
- Application Method
- Squeegee
- Components
- 2K
- Product Usage Type
- Sealer
- Product Usage Type
- Grout
- Product Range
- Resuflor
- Colour Family
- Clear
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
RSL Resuflor GC-UVR is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
RSL Resuflor Q Screed
A decorative epoxy resin floor screed incorporating multi-coloured aggregates, designed to produce a hard wearing, attractive, impervious sealed surface, sealed with clear resins to provide a matt or gloss finish. Formerly known as Resuscreed QS and Decora MS Decorative, hard wearing and durable Ease of application - low odour Good slip...
RSL Resuflor Screed
Resuflor Screed (formerly known as Resuscreed 45) is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be...
RSL Resuscreed 55
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
RSL Resuflor HB Clear
2-pack, high solids, high-build epoxy coating for application as a chemical resistant heavy duty floor coating, used as a clear sealer for decorative flooring systems such as RSL Resuflor Q Screed, producing a seamless, hard wearing, hygienic floor finish. Recommended uses include in food processing and beverage areas, chemical plant rooms,...