- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
3-pack, heavy-duty epoxy resin screed for new and existing concrete floors, laid from 6mm to 9mm nominal thickness.
- Formerly known as Resuscreed HCS and Resucrete.
- Withstands aggressive cleaning methods including thermal shock from steam cleaning and high pressure washing.
- Excellent adhesion.
- High compressive, tensile and flexural strength.
- Impervious.
- Good slip resistance.
- Excellent abrasion and impact resistance.
- Low odour.
- Excellent chemical resistance.
- See below for ordering references, available colours and lead times
Note that all colours have minimum order quantities of 93 units (25KG) with lead times of 7 working days due to being made to order
Resuflor Screed HCS (formerly known as Resuscreed HCS and Resucrete), is a three-pack, heavy-duty epoxy resin screed for new and existing concrete floors, laid from 6mm to 9mm nominal thickness. Resuflor Screed HCS offers excellent chemical resistance, high compressive and flexural strengths and very high impact resistance. Resuflor Screed HCS will withstand aggressive cleaning methods including thermal shock from steam cleaning and high pressure washing.
Recommended uses:
- Chemical production and storage
- Engineering and manufacturing facilities
- Pharmaceutical production
- Automotive industry
- Aerospace production areas
- Industrial workshops
- Commercial kitchens
Quick Links - Click To Jump To Section:
- Ordering References
- Features & Benefits
- Product Information
- Application Information (at 20℃)
- System Specification
- Preparation
- Priming
- Application
- Category Guide
- Technical Information
- Maintenance and Cleaning
Ordering References
Colour | Nearest RAL Match | Size | Finish | Mimimum Order Quantity |
---|---|---|---|---|
Flint Grey | RAL 7005 | 17KG or 34KG | Textured | 93 (25KG) - 5 working days lead time (made to order) |
Salsa Red | RAL 3011 | 17KG or 34KG | Textured | 93 (25KG) - 5 working days lead time (made to order) |
Stirling Grey | RAL 7004 | 17KG or 34KG | Textured | 93 (25KG) - 5 working days lead time (made to order) |
Features & Benefits
- Formerly known as Resucrete
- Three-pack
- Heavy-duty epoxy resin screed
- For new and existing concrete floors
- Laid from 6mm to 9mm nominal thickness
- Withstands aggressive cleaning methods including thermal shock from steam cleaning and high pressure washing
- Excellent adhesion
- High compressive, tensile and flexural strength
- Impervious
- Good slip resistance
- Excellent abrasion and impact resistance
- Low odour
- Excellent chemical resistance
Product Information
Product Information | |
---|---|
System Thickness (Recommended) | 6-9mm |
Solids Content by Weight | 98% |
Pack Sizes | 17 Kg & 34 Kg |
Pack Make Up | 1 x Base |
1 x Hardener | |
1 x Aggregate (for 17 Kg units) or 2 x Aggregate (for 34 Kg units) | |
Shelf Life | 36 months (Base, Hardener & Aggregate) |
Storage | Keep out of direct sunlight. Store in a dry place, between 15℃ - 30℃ |
Application Information (at 20℃)
Application Information | |
---|---|
Coverage Rate (Practical) | 17 Kg will cover 1.28 m2 at 6mm or 0.85 m2 at 9mm |
* Coverage rate is calculated based on a sealed and smooth surface and may vary based on the substrate roughness and other conditions. | |
Pot Life | 30 Minutes |
Recoating Intervals | For Seal Coats, 12 - 16 Hours |
Light Traffic | 12-16 hours |
Full Traffic | 72 hours |
Full Chemical Cure | 7 days |
System Specification
- Product: Resuflor Screed HCS
- Finish: Textured finish
- Recommended thickness range: 6mm to 9mm
Products required for this system
- Prime: Resuprime ST on dry substrates, or use Resuprime MVT on damp surfaces where required
- System: Resuflor Screed HCS
- Surface Seal: Not required. Optional seal coats include Resupen WB (For matt finishes) or Resutile (For increased chemical resistance)
Preparation
New concrete Floors: Must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue detergent is washed and removed by rinsing with clean water.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability as it may not be compatible with existing floor coating.
Where overcoating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated in the individual data sheets, the coating in each stage should be tack free, but not fully cured. If fully cured then mechanical preparation is required to ensure intercoat adhesion.
Priming
Open and porous substrates may require priming with Resuprime ST on dry substrates only with less than 75% ERH reading. Where the Relative Humidity of a substrate exceeds 75% ERH Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203:2017.
The number of coats to be applied is chosen in accordance with the following table.
ERH % | Required Coating Thickness |
---|---|
75-85 | 1 coat of Resuprime MVT at 200 microns per coat |
85-92 | 2 coats of Resuprime MVT at 200 microns per coat |
92-97 | 3 coats of Resuprime MVT at 200 microns per coat |
For further information please refer to recommended individual product data sheets.
Application
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system.
Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.
Mixing: Pre-mix the coloured base component to a uniform consistency (N.B. base will appear gelled in the tin but will become fluid with mixing) then mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied.
Add the aggregate component slowly whilst mixing. Mix using an electric mixer for approximately two to three minutes until the three components have fully combined. For larger units a forced action mixer may be required to fully combine the aggregate into the resins.
Resuflor Screed HCS should be worked with a trowel or float to achieve a dense, compacted finish. This is best achieved by the application of smooth even pressure in one direction, gradually increasing the pressure as the material compacts and beds down. Over-working the material will draw fines to the surface which may result in resin-rich spots and finish variations.
Category Guide
- FeRFA Category: 8
Technical Information
The following figures are obtained from laboratory tests and our experience with this product .
Technical Information | |
---|---|
Slip Resistance | Dry > 60 |
Method BS7976 pt1-3 2002 | Wet: Please consult our technical team |
The slip resistance of a floor surface can vary as a result of the installation process, conditions at the time of application and subsequent traffic. Inappropriate cleaning or maintenance can adversely affect the performance. For further advice on potential wet areas please consult our technical team. | |
Abrasion Resistance Method BS EN 13892-4:2002 | AR 0.5 |
Temperature Resistance | Tolerant of temperatures up to 60℃ |
Chemical Resistance | Excellent chemical resistance; consult our technical team on specific materials |
VOC | 49 g/l - Calculation based on a full mixed unit |
Maintenance and Cleaning
Sherwin-Williams recommend that Resuflor Screed HCS should be cleaned with a regular industrial cleaning regime with a floor scrubber utilising R.S. Industrial Floor Cleaner or similar with dirty water being removed. Isolated localised cleaning can be carried out using R.S. Tyre Mark Remover, Degreaser W500 & R.S. Oil Remover. All surfaces should be thoroughly rinsed with clean water after the use of chemical cleaners.
Data sheet
- For Use By
- Industrial Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Concrete Floors
- Application Method
- Trowel
Float - Single, Two or Three Pack
- Three-Pack
- Coverage
- 17kg will cover 1.28 m sq. @ 6mm or 0.85 m sq. @ 9mm
- Touch Dry
- 12-16 Hours
- Suitable For Use On
- Concrete Floors
- Application Method
- Float
- Application Method
- Trowel
- Components
- 3K
- Product Usage Type
- Coloured Screed
- Product Range
- Resuflor
- Colour Family
- Grey
- Colour Family
- Red
- Average Application Thickness
- 6-9mm
- Product Type
- Epoxy
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
RSL Resuflor Screed HCS is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
RSL Resuflor WB - Standard Readily Available Colours
A multi-purpose, two-pack, water-based epoxy coating in 13 colours primarily for concrete walls and floors. It can also be applied to concrete poured 7 days prior, as well as wood for a dust-free finish. These standard colours are readily available with faster shipping options; more colours are also available separately that are made to...
RSL Resupen WB - Standard Readily Available Colours
Extremely durable polyurethane finish for concrete, plaster and wood that produces a resilient coating on Sherwin-Williams wall and flooring systems. It is available in clear, colour, matt and satin finish. For more colours, see RSL Resupen WB - Special Colours. Chemical resistant and UV stable. Good abrasion and impact resistance....
RSL Resutile
We no longer stock this product, but can recommend RSL Resutile ST as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option...
RSL Resuprime ST Bonding & Priming Coat
2-pack, solvent-free epoxy resin bonding and priming coat. It bonds resin-based screeds and toppings to cementitious and other surfaces. Versatile for many types of application. Excellent adhesive properties. Easy to apply. Can be used as a tack coat for screeds. No unpleasant or harmful odours. Formerly known as Resuprime.
RSL Resuprime MVT
A faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Easy application Use on substrates with hygrometer readings <97% Solvent-free...