Follow us on:

RSL Resuflor Wall Gloss | Formerly Resuseal Wall Gloss) | Adhesive Epoxy Wall Coating

RSL Resuflor Wall Gloss

SEGLB
RSL2981

An aesthetic two-pack, hard-wearing, water-based epoxy wall coating with exemplary adhesion for concrete, wood and other surfaces.

  • Hygienic.
  • Dust-free.
  • Resistant to light chemical attack.
  • Low odour.
  • Decorative.
  • Formerly known as Resuseal Wall Gloss.
Colour
Size
Finish
£195.00(incl. VAT)
£162.50(ex. VAT)
Quantity
Please choose your colour
Please Contact our Technical Team on 0113 245 5450 (ext. 2) to Order this Product

questions 1 question about the product
Description

Resuflor Wall Gloss (Formerly known as Resuseal Wall Gloss) has an attractive and hard-wearing finish and is versatile in the surfaces for which it is suitable. It can be applied over previously painted surfaces as well as a variety of new ones.

Recommended Uses

  • Concrete
  • Plaster
  • Brick
  • Ceramics
  • Blockwork
  • Detainment centres
  • Laboratories
  • Food production areas
  • Motor garages

Preparation

Surfaces to be coated must be clean, sound, dry and free of any contaminants that could impair good adhesion. Hard smooth surfaces should be abraded or sanded to provide a mechanical key. Where open block work is to be coated, this should be filled and bag rubbed with a sand cement mix to create a continuous, smooth paintable surface.

Substrate temperature should be between 10-30°C with a relative air humidity of 70% maximum. Cold, high humidity and lack of air movement can cause a patchy finish, gloss reduction, a delay in curing and damage to final properties. To prevent this, ensure that good drying conditions and air ventilation prolong throughout the application and cure of the product.

Priming

Open and porous substrates will require priming. Resuflor WB Clear is recommended and depending on the porosity and texture of the surface to be primed, may require two coats. Resuflor WB Clear will not seal blockwork as it is a thin film primer.

Application

Mixing: Pre-mix the base component to a uniform consistency, then add the entire contents of the hardener to the base. Mix by using a slow speed hand held powered mixer and mixing paddle for approximately two to three minutes to achieve consistent mixture.

Note: Do not use a separate mixing bucket as it may affect the mixing ratio.

The mixed unit should be applied immediately by roller or brush with a consistent procedure, cross-rolling to ensure even application and to minimise roller marks. Coverage rates will depend on the porosity of the substrate.

Do not add water to this product.

Do not apply Resuflor Wall Gloss on top of polyurethane coatings, as it may not adhere properly.

Product Details
2981-937122

Data sheet

Manufacturer
RSL
For Use By
Industrial Use
Interior / Exterior Use
Interior Use
For Use On
Concrete Walls
Plaster Walls
Brick Walls
Ceramic Walls
Blockwork Walls
Application Method
Roller
Brush
Colour
Standard / Ready Mixed
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Two-Pack
Pack Size
5KG, 10KG
Coverage
5kg will cover 37m sq. @ 100 microns wet thickness.
Touch Dry
12-24 Hours
UN Number (Base)
UN3082
Base Type
Water-Based Epoxy
Suitable For Use On
Plasterboard Walls
Suitable For Use On
Block Walls
Suitable For Use On
Block
Suitable For Use On
Ceramic
Suitable For Use On
Laboratory Walls
Suitable For Use On
Detainment Centre Walls
Suitable For Use On
Food Production Walls
Suitable For Use On
Motor Garage Walls
Suitable For Use On
Workshop Walls
Suitable For Use On
Factory Walls
Suitable For Use On
Concrete
Suitable For Use On
Brick
Suitable For Use On
Ceramic Tile
Suitable For Use On
Plasterboard
Suitable For Use On
Concrete Walls
Suitable For Use On
Brick Walls
Finish
Gloss
Application Method
Brush
Application Method
Roller
Product Usage Type
Topcoat
Product Range
Resuflor
Colour Family
White
Product Focus
Scrubbable Paints
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)
questions tim shearing on 2024-01-29 13:42:05
Question: 

How many litres in a 5kg pack

Answer from Rawlins’ Technical Team:

A 5kg will cover 37m² @ 100 microns wet thickness.

This product is not sold or listed in litres.

IMPORTANT SHIPPING & DELIVERY INFORMATION

RSL Resuflor Wall Gloss is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like