- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
High-build polyaspartic/polyurea fast-cure floor coating system designed to create an advanced, tough and durable gloss finish in a range of thicknesses.
- Fast cure at low temperatures.
- Tough, yet flexible.
- Low odour.
- UV stable.
- High build.
- Can be used commercially/industrially.
- Can be used on a range of substrates.
- Note - more colours available on RSL Elladur SF - Special Colours
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
The game-changing, technological Elladur SF are very versatile systems. They can be created with anti-slip finishes and decorative finishes by incorporating the relevant flakes and aggregates to your flooring needs.
Recommended Uses
- Where a fast turnaround at a low temperature is required
- Decorative floors
- Domestic floors
- Medical areas
- Commercial environments
- Industrial floors
- Where high-build, UV stable coatings are needed
Preparation
New Concrete Floors: New concrete must be clean, sound, dry and fully cured and surface laitance removed preferably by vacuum enclosed shot blasting or mechanical grinding. A minimum strength of 25N/mm sq. is required.
Timber Floors: Must be clean, sound and dry. Old clear varnish/topcoat must be removed/sanded and surface must be primed prior to application.
Existing Concrete Floors: Remove all dirt, oil, grease old paints or other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Local repairs should be carried out using Resuscreed PA or Resuflor Screed.
Existing Floors (previously coated): All previous coatings and loose floor paints must be removed by mechanical preparation, as described in the above section and primed as specified. If the old resin flooring cannot be removed, then please consult with our technical team for advise on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.
Where over-coating other systems such as epoxy coatings or screeds, as part of a specified composite system in the data sheets, please follow the recoat time as stated. These should be tack free, but not fully cured. If fully cured, then mechanical preparation is required to ensure intercoat adhesion.
Where Elladur SF is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.
Priming
Elladur SF may be applied to an existing resin floor system, where a primer is not required. When applied direct to porous substrates such as concrete, the surface must be primed with Elladur SF to ensure good adhesion to the surface.
Where the relative humidity of the substrate exceeds 75%, Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203.
The number of coats to be applied is chosen in accordance with the following table:
ERH% Required Coating Thickness
75-85 1coat of Resuprime MVT at 200 microns per coat
85-92 2coats of Resuprime MVT at 200 microns per coat
92-97 3coats of Resuprime MVT at 200 microns per coat
Application
Mixing: Pre-mix the base component to a uniform consistency, then add the entire contents of the hardener to the base and mix by using a slow speed electric mixer for approximately two minutes to achieve consistent mixture. Do not use a separate mixing bucket as it may affect the mixing ratio.
A rubber blade and/or a short-haired roller can work best for this application, to help avoid incorporating extra air and moisture in the coating. It is important to ensure that the recoat times are observed, with a maximum recoat of 8 hrs measured at 20°C substrate temperature and 50% relative humidity.
For other conditions please consult with our technical team. It is strongly recommended to apply the second coat as soon as the first coat has lost the tackiness to achieve the maximum adhesion. If the maximum recoating interval is exceeded, then the surface must be prepared and roughened to ensure intercoat adhesion.
Data sheet
- Manufacturer
- RSL
- For Use By
- Industrial Use
- Interior / Exterior Use
- Interior Use
- For Use On
- Concrete, Wood
- Sheen
- Gloss
- Colour
- Clear, Standard / Ready Mixed
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5KG
- Coverage
- 5kg will cover between 6 to 20m2 depending on the applied thickness
- Min. Application Temperature
- 2°C
- Touch Dry
- 2-3 Hours
- Base Type
- Solvent-Free
- Suitable For Use On
- Concrete
- Suitable For Use On
- Wood
- Components
- 2K
- Usages
- Low Temperature
- Product Usage Type
- Topcoat
- Product Range
- Elladur
- Colour Family
- Grey
- Categorised As
- Floor Paints > Low Temperature Floor Paints
- Seasonal
- Cold Weather
- Product Type
- Polyaspartic
Questions
Question about the product
David Clark on 2023-06-28 18:10:21 | Question:
Is this paint suitable to be applied to steel posts fitted in a cavity of a property. Not external |
Answer from Rawlins’ Technical Team:
This product is normally used for applications to concrete or timber floors, please can you provide more information on the project to [email protected] so we can assist with a recommendation. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
RSL Elladur SF - Standard Readily Available Colours is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
RSL Resuflor Screed
Resuflor Screed (formerly known as Resuscreed 45) is a heavy duty, epoxy resin floor screed which uses a crystalline silica free aggregate, making it more environmentally friendly. Must seal for an impervious finish. Less dust than other screeds Low odour Hard wearing Abrasion and impact resistant Can form coving and falls Can be...
RSL Resuprime MVT
A faster curing version of R.S. Dampshield, with overcoat times of 6 hours. A two-component epoxy resin primer, it enables even earlier access onto new or existing concrete substrates for screed and coating applications on carpets, tiles, vinyl and wood. Easy application Use on substrates with hygrometer readings <97% Solvent-free...
RSL Resuflor Patch
RSL Resuflor Patch (Formerly known as Resuscreed PA and Resupatch) is a three-pack epoxy resin mortar designed for rapid concrete repair in heavy duty environments. Excellent mechanical properties Can be feather edged Abrasion and impact resistant Dust-free Concrete like in appearance Easy to apply Minimum surface preparation...