- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Britannia Walkway Safety Coating is based on an acrylic MMA copolymer. It provides a hard, tough, flexible and easy to apply film coating with excellent external durability and resistance to heat and alkaline conditions. It also contains polymer beads with outstanding slip resistance.
Ready for use over concrete and asphalt. Can be applied by brush or roller.
Note: Not a fully waterproofing system
Quick Links - Click To Jump To Section:
Features & Benefits
- Provides a hard, tough, flexible and easy to apply film coating
- Excellent external durability
- Resistance to heat and alkaline conditions
- Outstanding slip resistance
- Ready for use over concrete and asphalt
- Application by brush or roller
- Asphalt revival coating
- Rainfall immediately after application has no adverse effect
- Not a fully waterproofing system
Spreading Rate
These will vary depending on substrate, the site conditions and longevity required.
Typically spreading rates will vary depending on the end use.
- Approximately 0.8kg/m2
Drying Times
- Touch Dry (temperature depending): 3 – 4 hours
- Full Cure – Allow 8hrs
Preparation
Clear all areas of moss, lichen and debris by brushing or power washing and remove surface water. Apply Britannia Fungicidal Wash to prevent further fungal/algal growth.
Application Temperature should be between 5°C-25°C.
Highly Porous/Friable Surfaces:
- Subject to site inspection
Non-Porous Surfaces:
- Subject to site inspection
Bitumen Surfaces:
- Discolouration may occur over a volatile asphalt, tar or bitumen surface; therefore an extra coat may be required
Splits, Cracks, Joints and Seals:
- Pay particular attention to clean out any splits/cracks/joints and seals by scraping or brushing off with a stiff bristle brush
- Repair faults in the surface by embedding a polyester scrim in the first of two coats
- Cut the scrim to a suitable length to ensure an overlap of the ‘fault’ by 75mm all round and embed into the first coat of Britannia Walkway Safety Coating whilst still wet, making sure to force the coating through the mesh
Crazed Areas:
- Crazed areas should be filled using a suitable non-bituminous joint sealant prior to the application of a first coat
- Apply a second coat to the area repaired and then over the whole area to be coated as stated below
In areas where excessive movement may occur additional reinforcement must be incorporated into the coating.
Application
- Stir well before use
- To the dry and cleaned surface, apply a generous coat of Britannia Walkway Safety Coating by brush or roller
- Please follow the coverage rates shown in Spreading Rate Section
- Work away from the area immediately being applied and toward a suitable escape access
- Do not walk on newly coated surface whilst application is in progress
- Application Temperature should be between 5°C-25°C
Cleaning
- For cleaning equipment use Special Solvent (Not White Spirit)
Precautions
- Flammable keep away from sources of ignition
- Ensure good ventilation during application
- Wear gloves, goggles and suitable protective clothing
- In case of contact with eyes rinse immediately with plenty of water and seek medical advice
- Remove splashes from the skin with a recognised hand cleaner or plenty of soap and water
- Keep out of reach of children
- Do not use near fishponds
- Harmful to aquatic organisms
- May cause long term adverse effects in the aquatic environments
- Do not empty into drains
- Do not breathe vapour or spray
- Britannia Walkway Safety Coating is not recommended for the treatment of wooden surfaces, tanking, fishponds or internal use
- Air conditioning vents should be sealed for a minimum of 24 hours during and after the application
Data sheet
- Manufacturer
- Britannia
- Interior / Exterior Use
- Exterior Use
- Water / Solvent Based
- Solvent
- For Use On
- Concrete, Asphalt
- Application Method
- Brush, Roller
- Sheen
- Semi-Gloss
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 5KG, 20KG
- Coverage
- Approximately 0.8kg/m²
- Touch Dry
- 3-4 hours (temperature depending) Full cure: allow 8 hours.
- UN Number
- UN1263
- Base Type
- Solvent-Based
- Suitable For Use On
- Concrete
- Suitable For Use On
- Asphalt
- Suitable For Use On
- Bitumen
- Suitable For Use On
- Concrete Walkways
- Suitable For Use On
- Asphalt Walkways
- Finish
- Semi-Gloss
- Application Method
- Brush
- Application Method
- Roller
- Components
- 1K
- Usages
- Anti-Slip
- Product Usage Type
- Topcoat
- Colour Family
- Grey
- Colour Family
- Black
- Colour Family
- Anthracite Grey
- Anti-Slip Texture
- Fine Texture
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Britannia Walkway Safety Coating is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT