- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Rock mineral fibre board coated with smoke and fire resistant sealant, provides up to 90
- 1200 x 600 x 70 mm size
- Contact our sales team on 0113 2455450 if custom sizes required
- Simple installation method
- Contributes to acoustic upgrade
- Optifire technology identification
Where ceilings cannot be disturbed, such as decorative or made from lath and plaster, fire protection can be installed under the floor above. Nullifire FB770 Intudeck is a rock mineral wool slab coated on one or both sides with a smoke and fire resistant sealant that provides up to 90 minutes of fire protection.
Supplied in 1200 x 600 x 70 mm sizes with 140 kg/m³ density; please contact our sales team on 0113 2455450 if you require a custom size.
These fire batts are lightweight and quick to install, cutting easily to the desired size on-site. Fit between joists underneath floorboards, using compression and Intumastic bonding, to upgrade the fire resistance of timber floors. Services such as combustible pipework, steel pipework and cables can be accommodated - please contact our technical team on 0113 2455450 for detailed solutions.
Nullifire FB770 Intudeck is ideal for fire protection properties with inaccessible ceilings spaces, either due to occupancy or mechanical services, in small and large projects in both small units such as flats over shops, as well as large projects such as
Use fire barriers to compartmentalise spaces, rooms and areas. This helps slow down the spread of smoke and fire, giving more time for evacuation of staff and customers to help save lives and prevent injury, as well as helping keep damage to a minimum whilst emergency services arrive to tackle the fire.
Typical Installation
Observe Intudeck safety data sheet before commencing work.
- Lift sufficient floorboards to allow
Intudeck to be installed. - Clear any remaining pugging from the ceiling/floor void and clear dust from the sides of the joists to improve the adhesion of the bonding Intumastic.
- Apply a 10mm bead of Intumastic to the side of each joist 35mm from the bottom.
- If adhesion is difficult, spray the joist with water from a small garden spray.
- Measure the gap between joists and cut an
Intudeck batt along the 1200mm side to fit tightly and under compression. - Place loosely in position at 45° between joists. Using a timber board to spread the load, ease into final position using gentle foot pressure.
- When finally positioned, apply a 5mm bead of Intumastic all around the seal and on the butt joints.
- Inspect and check completed work and re-fix floorboards
Fire Testing
IMPORTANT FIRE PRODUCTS NOTICE: The information displayed on this website should be used as a guide ONLY and our Technical Department should be contacted to obtain a tailored specification and any advice necessary before you place an order for fire protection products. Fire protection products are non-returnable except in accordance with Condition 8 of the Terms and Conditions and should be applied only by an individual with the necessary expertise and experience. We will not be held liable for any resulting damage to property, human life or monetary costs incurred due to the incorrect specification you have prepared or use of fire protection products caused by your negligence, including your failure to have contacted us to obtain the relevant advice/specification.
Data sheet
- Single, Two or Three Pack
- Single
- Suitable For Use On
- Ceilings
- Suitable For Use On
- Timber Floors
- Application Method
- Hand
- Product Usage Type
- Fire Barrier
- Fire Rating
- 90 Minutes
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Nullifire FB770 Intudeck is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT