- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Carboline Carbomastic 15 LT is a two-component, high build coating with excellent adhesion to rusted steel and most aged coatings.
- Surface tolerant
- Recommended for painting over rusted steel where hand cleaning only is possible
- Carbomastic 15 LT penetrates through rust to steel substrate and stops further corrosion and undercutting
- Fast curing at low temperatures
- High solids give good coverage and reduced solvent emission
- Excellent maintenance primer for piping, bridges, tank exteriors, ships and offshore structures, etc
- Also available in 20L - price on application - contact our sales team for more information on 0113 2455450 or send a message to [email protected].
Carboline Carbomastic 15 LT is a two-component, high build coating with excellent adhesion to rusted steel and most aged coatings.
Click To Jump To Section:
- Features and Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application Methods
- Application Conditions
- Health and Safety
Features and Benefits
- Surface tolerant
- Recommended for painting over rusted steel where hand cleaning only is possible
- Carbomastic 15 LT penetrates through rust to steel substrate and stops further corrosion and undercutting
- Fast curing at low temperatures
- High solids give good coverage and reduced solvent emission
- Excellent maintenance primer for piping, bridges, tank exteriors, ships and offshore structures, etc
Product Specification
Technical Data | ||||||
---|---|---|---|---|---|---|
Carboline Carbomastic 15 LT | ||||||
Volume Solids: | 86 ± 2% | |||||
Theoretical Coverage Rate: | 5,7 m²/l at 150 µm | |||||
Allow for loss in mixing and application. | ||||||
Dry Film Thickness: | 100 - 300 microns (3.94 - 11.81 mils) per coat | |||||
Normally 150 µm | ||||||
Wet Film Thickness: | 115 – 350 µm per coat, normally 175 µm | |||||
Dry Temperature Resistance: | Continuous: 120°C (248°F) | |||||
Non-Continuous: 150°C (302°F) | ||||||
Topcoats: | May be topcoated with most generic types. Some alkys or oil modified paints exhibit poor adhesion. Topcoat should be applied within 14 days | |||||
Limitations: | Not recommended for immersion service in acids, alkalies or solvents | |||||
Shelf Life: | 24 months at 24°C | |||||
Storage Temperature and Humidity: | 5° - 45°C | |||||
0 – 95% relative humidity |
Drying Times
Curing Schedule | ||||||
---|---|---|---|---|---|---|
Surface Temp. | Dry to Recoat | Final Cure | ||||
5°C (41°F) | 18 Hours | 7 Days | ||||
10°C (50°F) | 10 Hours | 5 Days | ||||
20°C (68°F) | 6 Hours | 3 Days | ||||
25°C (77°F) | 4 Hours | 2 Days |
- These times are based on recommended DFT. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure
Surface Preparation
General
- May be used over most generic types of coatings which are tightly adhering to the substrate including organic- and inorganic zinc primers
Steel
- Preferably blasting however hand- or power tool cleaning is acceptable standard in many cases to remove non adhering paint and rust. Alternatively, ultra high pressure water jetting to Nace No. 7 min. C Vis WJ-2. Max flash rust; C Vis WJ-2M
Application Methods
Product Information | |||||
---|---|---|---|---|---|
Mixing: | Power mix separately, then combine and power mix | ||||
Thinning: | May be thinned up to 15% with Thinner 2. Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied | ||||
Ratio: | 1:1 Ratio (A to B) by volume | ||||
Pot Life: | 1½ hours at 20°C and less at higher temperatures | ||||
Airless Spray: | Pump Ratio: 30:1 (minimum) | ||||
GPM Output: 3.0 (minimum) 12 liters/min. | |||||
Material Hose: 3/8” I.D. (minimum) | |||||
Tip Size: .023” - .027” | |||||
Output PSI: 2000 - 2400 | |||||
Filter Size: 60 mesh | |||||
Brush and Roller: | Recommended for small areas and touch-up only |
Application Conditions
Product Conditions | |||||
---|---|---|---|---|---|
Condition | Material | Surface | Ambient | Humidity | |
Minimum | 5°C (41°F) | 2°C (36°F) | 2°C (36°F) | 0% | |
Maximum | 35°C (95°F) | 75°C (167°F) | 40°C (104°F) | 85% |
- Industry standards are for substrate temperatures to be 3°C above the dew point. Special application techniques may be required above or below normal application conditions
Health and Safety
Clean Up
- Use Thinner 2 or Thinner 25
- In case of spillage, absorb and dispose of in accordance with local applicable regulations
Safety
- Read and follow all caution statements on this product data sheet and on the safety data sheet for this product
- Employ normal workmanlike safety precautions
- Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands, and all exposed areas
Ventilation
- When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
- The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
Caution
- This product contains flammable solvents. Keep away from sparks and open flames
- All electrical equipment and installations should be made and grounded in accordance with the applicable local regulations
- In areas where explosion hazards exist, workmen should be required to use non-ferrous tools and wear conductive and non-sparking shoes
- Refer to the product and safety data sheet in the attachments section above for further details
Data sheet
- Manufacturer
- Carboline
- For Use By
- Industrial Use
- Interior / Exterior Use
- Interior & Exterior
- For Use On
- Steel Pipes
Steel Bridges
Steel Tank Exteriors
Ships
Steel Offshore Structures
Inorganic Zinc Primers
Organic Zinc Primers - Application Method
- Brush
Roller
Spray - Sheen
- Semi-Gloss
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5L
20L - Mixing Ratio
- 1:1 Ratio (A to B) by volume
- Dry to Recoat (at 20°C)
- 6 Hours
- Fully Cured (at 20°C)
- 3 Days
- Pot Life (at 20°C)
- 1½ hours
- Coverage
- 5,7 m²/l at 150 µm
- Recommended Thinner/Cleaner
- Carboline Thinner 2 or Carboline Thinner 25
- Compatible Topcoats
- May be topcoated with most generic types. Some alkys or oil modified paints exhibit poor adhesion. Topcoat should be applied within 14 days.
- Max. Application Temperature
- Material: 35°C (95°F) - Surface: 75°C (167°F) - Ambient: 40°C (104°F) - Humidity: 85%
- Min. Application Temperature
- Material: 5°C (41°F) - Surface: 2°C (36°F) - Ambient: 2°C (36°F) - Humidity: 0%
- Solids by Volume
- 86 ± 2%
- Shelf Life (from date of manufacture)
- 24 months at 24°C
- Recommended Dry Film Thickness
- 100 - 300 microns (3.94 - 11.81 mils) per coat
- Recommended Wet Film Thickness
- 115 – 350 µm per coat, normally 175 µm
- UN Number (Activator)
- UN3469
- UN Number (Base)
- UN1263
- Dry to Recoat (at 10°C)
- 10 Hours
- Fully Cured (at 10°C)
- 5 Days
- Base Type
- Solvent
- Base Type
- Epoxymastic
- Suitable For Use On
- Zinc
- Suitable For Use On
- Steel
- Suitable For Use On
- Metal Pipes
- Suitable For Use On
- Steel Hulls
- Suitable For Use On
- Steel Exteriors of Tanks
- Suitable For Use On
- Steel Bridges
- Suitable For Use On
- Inorganic Zinc Primers
- Suitable For Use On
- Steel Pipes
- Suitable For Use On
- Steel Tank Exteriors
- Suitable For Use On
- Ships
- Suitable For Use On
- Steel Offshore Structures
- Suitable For Use On
- Organic Zinc Primers
- Finish
- Semi-Gloss
- Application Method
- Roller
- Application Method
- Spray
- Application Method
- Brush
- Manufacturer
- Carboline
- Components
- 2K
- Usages
- High Solids
- Usages
- High Build
- Usages
- Low Temperature
- Usages
- Surface Tolerant
- Usages
- Atmospheric
- Usages
- Anti-Corrosive
- Product Usage Type
- Primer
- Product Usage Type
- Mid Coat
- Product Range
- Carbomastic
- Colour Family
- Aluminium
- Dry to Recoat (@ 20-25°C)
- 6 hours
Questions
Question about the product
patrick on 2022-08-03 18:22:51 | Question:
Is Carbomastic 15LT suitable for achieving fire protecting of internal steel structure for 60minutes (domestic project)? If so could you send supporting information. |
Answer from Rawlins’ Technical Team:
No, we can assist with a specification for your steels, please send the information below to [email protected] - Level of fire protection required (i.e. 30, 60, 90min, etc.) | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
Carboline Carbomastic 15 LT is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.
Carboline Thinner 25
Carboline Thinner 25 is a thinner for use in industrial coatings.
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...