- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
2-component, high performance tank lining with curing characteristics allowing the coating to be applied and cure at temperatures as low as 2°C while achieving unmatched chemical resistance in caustic, acid, solvent and ethanol service. Formulated for use in a large variety of facilities including waste water, chemical and fuel storage, wet-gas pipelines, rail cars, barges and ship tanks.
- Outstanding overall chemical resistance.
- Superior immersion resistance.
- Excellent abrasion resistance and toughness.
- Well-suited for hydrocarbon exposures.
- Dry temperature resistant up to 121°C (continuous) and 149°C (non-continuous).
- For industrial use only.
This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450 or email [email protected].
Description
Carboline Plasite 9060 LT is a two-component, high performance tank lining with curing characteristics allowing the coating to be applied and cure at temperatures as low as 2°C while achieving unmatched chemical resistance in caustic, acid, solvent and ethanol service. The diversity of chemical resistance and unique low temperature curing allows the owner flexibility with their equipment. For industrial use only.
Click To Jump To Section:
- Features and Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application Methods
- Application Conditions
- Health and Safety
Features and Benefits
- Outstanding overall chemical resistance
- Dense, highly cross-linked film for superior barrier protection
- Superior immersion resistance
- Excellent abrasion resistance and toughness
- Well-suited for hydrocarbon exposures
- Formulated for use in a large variety of facilities including waste water, chemical and fuel storage, wet-gas pipelines, rail cars, barges and ship tanks
- Bis A free
- Dry temperature resistant up to 121°C (continuous) and 149°C (non-continuous)
- Cures down to 2°C
Product Specification
| Technical Data | |
|---|---|
| Carboline Plasite 9060 LT | |
| Volume Solids: | 76% +/- 2% |
| Theoretical Coverage Rate: |
29.9 m²/l at 25 microns 6.0 m²/l at 125 microns 5.0 m²/l at 150 microns |
| Allow for loss in mixing and application | |
| HAPs Values: |
As supplied: 1.35 lbs/solid gallon These are nominal values and may vary by colour |
| Dry Film Thickness: |
127 - 152 microns per coat Two coats are generally recommended to 200-250 microns total DFT |
| VOC Values: |
As Supplied: 197 g/l These are nominal values and may vary slightly with colour |
| Dry Temp. Resistance: |
Continuous: 121°C Non-Continuous: 149°C Discolouration and loss of gloss is observed above 93°C |
| Limitiations: |
Linings exposed to cargos warmer than the outside steel temperature are subject to a “cold-wall” effect. The smaller the temperature differential the less negative effect on performance. Epoxies lose gloss, discolour, and eventually chalk in sunlight exposure |
| Flash Point: |
Part A: 27°C Part B: 13°C Mixed: 32°C |
| Shelf Life: |
Part A and B: Min. 24 months at 24°C Shelf Life: (actual stated shelf life) when kept at recommended storage conditions and in original unopened containers |
Drying Times
| Curing Schedule | |||
|---|---|---|---|
| Surface Temp | Final Cure Immersion | Maximum Recoat Time | Minimum Recoat Time |
| 2°C | 15 Days | 10 Days | 18 Hours |
| 10°C | 10 Days | 7 Days | 12 Hours |
| 16°C | 7 Days | 5 Days | 8 Hours |
| 24°C | 5 Days | 3 Days | 6 Hours |
| 32°C | 3 Days | 1 Day | 4 Hours |
- These times are based on a 125-175 microns dry film thickness and adequate ventilation for the release of solvents for proper cure
- Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment, delamination between coats and premature failure
- Excessive humidity or condensation on the surface during curing can interfere with the cure, can cause discolouration, and may result in a surface haze. Any haze or blush must be removed by water washing before recoating
- If the maximum recoat time is exceeded, the surface must be abraded prior to the application of additional coats
- Note: It is recommended to cure above 16°C for aggressive service
| Curing Schedule | |||
|---|---|---|---|
| Surface Temp | Final Cure Immersion | ||
| 66°C | 8 Hours | ||
| 77°C | 3.5 Hours | ||
| 88°C | 2 Hours | ||
- The above curing schedule may be used to force cure the coating system
- Allow the freshly applied coating to air dry for 4 hours prior to elevating temperature
- Elevate temperature no more than 15°C every 30 minutes
- Force curing at temperatures approaching 88°C can result in a very slight colour change to the Plasite 9060 LT
Surface Preparation
| Preparation | |
|---|---|
| General: |
Surfaces must be clean and dry Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating |
| Steel: | Immersion: SSPC-SP10 minimum Profile: 38-75 microns |
| Concrete or CMU: |
Immersion: Concrete must be cured 28 days at 24°C and 50% relative humidity or equivalent Prepare surfaces in accordance with ASTM D4258-92 Surface Cleaning of Concrete and ASTM D4259 Abrading Concrete Voids in concrete may require surfacing |
Application Methods
| Product Information | |
|---|---|
| Mixing: |
Power mix separately, then combine and power mix Use material immediately after mixing Do not mix partial kits |
| Thinning: |
May be thinned up to 8 oz/gal with Thinner 2 Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied |
| Ratio: | 4:1 A:B |
| Pot Life: |
1 Hours at 24°C Pot life ends when coating shows dramatic changes in viscosity Pot life times will be less at higher temperatures |
| Conventional Spray: | Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, 0.055-0.070” I.D. fluid tip and appropriate air cap. |
| Airless Spray: |
Pump Ratio: 30:1 (min.) GPM Output: 3.0 (min.) Material Hose: 3/8” I.D. (min.) Tip Size: 0.015-0.019” Output PSI: 2100-2300 Filter Size: 60 mesh |
| Brush and Roller: | Not recommended for tank lining applications except when striping welds and touching up |
| Brush: | Use a medium bristle brush |
| Roller: | Use a short-nap synthetic roller cover with phenolic core |
Application Conditions
| Conditions | ||||
|---|---|---|---|---|
| Condition | Material | Surface | Ambient | Humidity |
| Minimum | 16°C | 2°C | 2°C | 0% |
| Maximum | 32°C | 43°C | 38°C | 85% |
- This product simply requires the substrate temperature to be above the dew point
- Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate
- Special application techniques may be required above or below normal application conditions
Health and Safety
Clean Up
- Use Thinner 2 or Acetone
- In case of spillage, absorb and dispose of in accordance with local applicable regulations
Safety
- Observe the precautionary notices on the container label, and read the safety data sheet before use
- Employ normal workmanlike safety precautions
Ventilation
- When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
- The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
- In addition to ensuring proper ventilation, appropriate respirators must be used by all application personnel
Caution
- This product contains flammable solvents
- Keep away from sparks and open flames
- All electrical equipment and installations should be made and grounded in accordance with regulations
- In areas where explosion hazards exist, workers should be required to use non-ferrous tools and wear conductive and non-sparking shoes
- Refer to the product data sheet and safety data sheets in the attachments section above for further details
Product Details
3723-800818
Data sheet
- Manufacturer
- Carboline
- For Use By
- Industrial Use
- For Use On
- Steel, Concrete
- Application Method
- Brush, Roller, Spray
- Sheen
- Gloss
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Mixing Ratio
- 4:1 A:B
- Coverage
- 29.9 m²/l at 25 microns, 6.0 m²/l at 125 microns, 5.0 m²/l at 150 microns
- Recommended Thinner/Cleaner
- Carboline Thinner 2
- Max. Application Temperature
- Material: 32°C, Surface: 43°C, Ambient: 38°C, Humidity: 85%
- Min. Application Temperature
- Material: 16°C, Surface: 2°C, Ambient: 2°C, Humidity: 0%
- Solids by Volume
- 76% +/- 2%
- Heat Resistance (up-to)
- Continuous: 121°C, Non-Continuous: 149°C
- VOC
- As Supplied: 197 g/l
- Shelf Life (from date of manufacture)
- 24 months at 24°C
- Recommended Dry Film Thickness
- 127 - 152 microns per coat
- UN Number (Activator)
- UN3066
- UN Number (Base)
- UN1263
- Pot Life
- 1 Hours at 24°C
- Dry to Recoat
- 2°C: 18 hours - 10 days, 10°C: 12 hours - 7 days. 16°C: 8 hours - 5 days, 24°C: 6 hours - 3 days, 32°C: 4 hours - 1 day
- Fully Cured
- 2°C: 15 days, 10°C: 10 days, 16°C: 7 days. 24°C: 5 days. 32°C: 3 days
- Suitable For Use On
- Concrete
- Suitable For Use On
- Steel
- Finish
- Gloss
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Tank Lining
- Product Range
- Plasite
- Categorised As
- Special Use > Low Temperature Tank & Pipe Lining Coatings
- Seasonal
- Cold Weather
- For Tanks or Pipes
- Tank & Pipe
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Carboline Plasite 9060 LT is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.
Price
£37.88
(incl. VAT)
In Stock and Available for Delivery
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Price
£25.93
(incl. VAT)
In Stock and Available for Delivery