- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Carboline Polyclad 975 H is an advanced two-component epoxy, 100% solids, hybrid epoxy pipeline coating.
- Quick dry to touch and QC times - good brush and roll properties
- Colour indicator confirms proper mixing
- Low temperature cure 4.4°C
- Excellent cathodic protection performance
- Film build up to 30 mils DFT in one coat
- Excellent edge retention
- Superior adhesion to steel
- Excellent adhesion over prepared FBE, epoxy and polyurethane coated pipe
- Can be hand applied by brush or roller
This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450 or email [email protected].
Description
Carboline Polyclad 975 H is an advanced two-component epoxy, 100% solids, hybrid epoxy pipeline coating. It has performance properties designed for corrosion protection of steel and ductile iron pipe exteriors, girth welds or tie-ins. Polyclad 975 H cures fast to allow quick QC and backfill times.
Two versions of this product are available as follows:
Apply by hand (brush/roller): Carboline Polyclad 975 H (this product)
Apply by spray: Carboline Polyclad 975
Approvals
- Meets criteria for AWWA C210-7
Click To Jump To Section:
- Features and Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application Methods
- Application Conditions
- Health and Safety
Features and Benefits
- Quick dry to touch and QC times
- Good brush and roll properties
- Colour indicator confirms proper mixing
- Low temperature cure 4.4°C
- Excellent cathodic protection performance
- Film build up to 30 mils DFT in one coat
- Excellent edge retention
- Superior adhesion to steel
- Excellent adhesion over prepared FBE, epoxy and polyurethane coated pipe
- Can be hand applied by brush or roller
- Semi-gloss finish
Product Specification
| Technical Data | |
|---|---|
| Carboline Polyclad 975 H | |
| Primer: | Self-priming |
| Volume Solids: | 99% +/- 1% |
| Theoretical Coverage Rate: |
39.0 m²/l at 25 microns 1.9 m²/l at 500 microns 1.3 m²/l at 750 microns Allow for loss in mixing and application |
| Dry Film Thickness: |
508 - 762 microns Typical DFT with hand application Do not exceed 50 mils in one coat |
| VOC Values: | As Supplied: 5 g/l |
| Dry Temp. Resistance: |
Continuous: 93°C Non-Continuous: 121°C |
| Flash Point: |
Part A: 96°C Part B: 96°C |
| Shelf Life: |
12 months Shelf Life: (actual stated shelf life) when kept at recommended storage conditions and in original unopened containers |
| Performance Data | ||
|---|---|---|
| Test Method | System | Results |
| Cathodic Disbondment ASTM G-95, 24°C (75°F), -1.5 V, 28 days | 20 to 30 mils DFT (500 to 750 microns) | <3 mm |
| Cathodic Disbondment ASTM G-95, 65°C (149°F), -1.5 V, 28 days | 20 to 30 mils DFT (500 to 750 microns) | <4 mm |
| Cathodic Disbondment ASTM G-95, 65°C (149°F), -3.0 V, 7 days | 20 to 30 mils DFT (500 to 750 microns) | <5 mm |
| Cathodic Disbondment ASTM G-95, 80°C (176°F), -1.5 V, 28 days | 20 to 30 mils DFT (500 to 750 microns) | <6 mm |
| Chemical resistance immersion, NACE TM 0174 method-B, 24°C for 7 days | 20 to 30 mils DFT (500 to 750 microns) | Results below |
| Chemical tested: 10% Nitric Acid | 20 to 30 mils DFT (500 to 750 microns) | Pass, no effect |
| Chemical tested: 10% Sodium Chloride | 20 to 30 mils DFT (500 to 750 microns) | Pass, no effect |
| Chemical tested: 10% Sodium Hydroxide | 20 to 30 mils DFT (500 to 750 microns) | Pass, no effect |
| Chemical tested: 5% Sulfuric Acid | 20 to 30 mils DFT (500 to 750 microns) | Pass, no effect |
| Chemical tested: Fuel Grade Ethanol | 20 to 30 mils DFT (500 to 750 microns) | Pass, no effect |
| Chemical tested: Toluene | 20 to 30 mils DFT (500 to 750 microns) | Pass, no effect |
| Flexibility, CSA Z245.20-10 (12.11) at 23°C | 27 to 30 mils DFT (686 to 750 microns) | Pass 1.0°/pd |
| Impact resistance, ASTM D2794 | 20 to 30 mils DFT (500 to 750 microns) | 45 in-lbs (5 Joules) |
| Shore D hardness, ASTM D2240 | 30 to 40 mils DFT (750 to 1000 microns) | 75-85 Shore D |
| Wet Adhesion, hot water soak for 24 hours, | 20 to 30 mils DFT (500 to 750 microns) | Rating #1 |
Drying Times
| Curing Schedule | ||||
|---|---|---|---|---|
| Surface Temp | Dry to Handle | Dry to Touch | Maximum Recoat Time | |
| 2°C | 15 Hours | 6 Hours | 12 Hours | |
| 10°C | 13 Hours | 3.5 Hours | 6 Hours | |
| 24°C | 3 Hours | 1 Hour | 4 Hours | |
| 32°C | 1.5 Hours | 0.75 Hours | 2 Hours | |
- Over-coating after the maximum recoat time requires that the surface be abraded prior to application
- Use a medium grit, 60 to 80 grit paper or sweep blast to roughen the surface
- Clean abraded area of dust before recoating or repair
- Coating is ready for backfill when it is "thumb nail" hard
- The thumb nail hardness is defined by when one cannot make a permanent indention in the coating with one's thumb
Surface Preparation
| Preparation | |
|---|---|
| General: |
All sharp edges shall be ground to produce a radius and all imperfections, such as, delaminations, scabs, slivers and slag shall be corrected prior to abrasive blasting Degrease surface prior to abrasive blast in accordance to SSPC SP-1 Organic solvents, alkaline solutions, steam, hot water with detergents or other systems that will completely remove dirt, oil, grease, etc. may be used |
| Steel: | Steel substrate must be blasted to a minimum Near-White Metal Finish (SSPC SP10 or NACE NO. 2) with a 2.5 to 4.5 mil (62 to 112 microns) dense, sharp angular profile |
Application Methods
| Product Information | |
|---|---|
| Mixer: | Use 1/2" electric or air driven drill with a slotted paddle mixer (300 rpm under load) |
| Mixing: |
Open and make sure part B is homogenous Mix part B if needed. Pour part B in the part A bucket Mix until the colour is uniform and the colour from part B is totally incorporated
|
| Thinning: | Thinning is not required |
| Ratio: | 4:1 Ratio by volume (Part A to Part B) |
| Pot Life: |
15 minutes @ 24°C (75°F) *These are general guidelines for the application of this product. Job site conditions may require modifications to these guidelines to achieve the desired results |
| Brush and Roller (General): |
May be hand applied by first mixing the coating then immediately pouring it onto the pipe surface Spread the coating to desire thickness using brush or roller Measure the film thickness with wet film gauge |
Application Conditions
| Conditions | ||||
|---|---|---|---|---|
| Condition | Material | Surface | Ambient | Humidity |
| Minimum | 18°C | 4°C | -7°C | 0% |
| Maximum | 38°C | 43°C | 43°C | 90% |
- This product simply requires the substrate temperature to be above the dew point
- Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate
Health and Safety
Clean Up
- Use Thinner 2 or Thinner 225 E
- In case of spillage, absorb and dispose of in accordance with local applicable regulations
Safety
- Observe the precautionary notices on the container label, and read the safety data sheet before use
- Employ normal workmanlike safety precautions
Ventilation
- When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
- Minimal protection is needed when proper ventilation is achieved
Caution
- This product contains flammable solvents
- Keep away from sparks and open flames
- All electrical equipment and installations should be made and grounded in accordance with regulations
- In areas where explosion hazards exist, workers should be required to use non-ferrous tools and wear conductive and non-sparking shoes
- Refer to the product data sheet and safety data sheet in the attachments section above for further details
Product Details
3734-801697
Data sheet
- Manufacturer
- Carboline
- For Use By
- Industrial Use
- For Use On
- Steel, Iron
- Application Method
- Brush, Roller
- Sheen
- Semi Gloss
- Colour
- Standard / Ready Mixed
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Two-Pack
- Parts
- Two
- Base Type
- Hybrid epoxy
- Solvent
- Epoxy
- Mixing Ratio
- 4:1
- Suitable Substrates
- Steel and iron piping
- Key Features
- Low temperature cure, excellent edge retention, superior adhesion to steel
- Application
- Brush, Roller
- Coverage
- 1588 ft²/gal at 1.0 mils (39.0 m²/l at 25 microns). 79 ft²/gal at 20.0 mils (1.9 m²/l at 500 microns). 53 ft²/gal at 30.0 mils (1.3 m²/l at 750 microns). Allow for loss in mixing and application.
- Recommended Thinner/Cleaner
- Thinning is not required. For cleaning, use Carboline Thinner #2 or Carboline Thinner 225E
- Compatible Primers
- Self-priming
- Max. Application Temperature
- Material: 38°C, Surface: 43°C, Ambient: 43°C, Humidity: 90%
- Min. Application Temperature
- Material: 18°C, Surface: 4°C, Ambient: -7°C, Humidity: 0%
- Solids by Volume
- 99% +/- 1%
- Heat Resistance (up-to)
- 250°F (121°C)
- VOC
- 0.04 lbs./gal (5 g/L)
- Shelf Life (Once Opened)
- Part A: 12 months Part B: 12 months
- Touch Dry
- 2°C: 6 Hours, 10°C: 3.5 Hours, 24°C: 1 Hour, 32°C: 0.75 Hours
- Dry to Handle (at 10°C)
- 13 Hours
- Base Type
- Hybrid Epoxy
- Suitable For Use On
- Steel
- Suitable For Use On
- Iron
- Finish
- Semi-Gloss
- Application Method
- Brush
- Application Method
- Roller
- Product Usage Type
- Pipe Lining
- Product Range
- Polyclad
- Categorised As
- Special Use > Low Temperature Tank & Pipe Lining Coatings
- Seasonal
- Cold Weather
- For Tanks or Pipes
- Pipe
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Carboline Polyclad 975 H is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
Carboline Polyclad 975
Carboline Polyclad 975 is an advanced two-component, 100% solids, hybrid epoxy pipeline coating. Polyclad 975 has performance properties designed for corrosion protection of steel and ductile iron pipe exteriors, girth welds or tie-ins. Quick dry to touch and QC times Colour indicator confirms proper mixing Low temperature cure 4.4°C...
Price
£0.00
(incl. VAT)
In Stock and Available for Delivery
Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.
Price
£37.88
(incl. VAT)
In Stock and Available for Delivery
Carboline Thinner 225 E
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
In stock
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Price
£25.93
(incl. VAT)
In Stock and Available for Delivery