- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Carboline Thermaline 4674 is a single package medium to high temperature coating that withstands continuous temperature up to 400ºC peaks up to 540ºC. May be applied directly to properly prepared steel.
- Resistant to thermal shock conditions from ambient temperature to 400ºC
- Excellent weathering properties
- Gloss finish
- 10L Aluminium also available - price on application - contact our sales team for more information on 0113 2455450 or send a message to [email protected].
Carboline Thermaline 4674 is a single package medium to high temperature coating that withstands continuous temperature up to 400ºC peaks up to 540ºC. May be applied directly to properly prepared steel. Application over inorganic zinc primers like Carbozinc 11 will provide superior performance by preventing rusting and rust streaking during a shutdown or when the equipment is exposed to moisture and/or salts at temperature less than 93ºC.
Click To Jump To Section:
- Features and Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application Methods
- Application Conditions
- Health and Safety
Features and Benefits
- Resistant to thermal shock conditions from ambient temperature to 400ºC
- Excellent weathering properties
- Gloss finish
Product Specification
Technical Data | |
---|---|
Carboline Thermaline 4674 | |
Primer: |
None required A primer coat of Carbozinc will greatly increase performance over steel |
Topcoats: | Normally none |
Solid(s) Content: | By Volume 45 ± 2% |
Theoretical Coverage Rate: |
11,2 m²/l at 40 µm Allow for loss in mixing and application |
Dry Film Thickness: |
30 - 80 microns (1.18 - 3.15 mils) per coat Normally 40 µm. Two coats are recommended over bare steel and one or two coats over inorganic zincs such as Carbozinc 11 Excessive film thickness over inorganic zincs may result in blistering and delamination when temperature is increased. |
Wet Film Thickness: | 65 - 175 µm per coat, normally 90 µm |
Dry Temp. Resistance: |
Continuous: 400°C (752°F) Non-Continuous: 540°C (1004°F) |
Limitations: | Not recommended for linings or immersion service and exposure to splash and spillage of acids and alkalis |
Shelf Life: | 2 years at 24ºC |
Drying Times
Curing Schedule | ||||
---|---|---|---|---|
Surface Temp. | Between Coats | Final Cure | ||
10°C | 8 Hours | 10 Hours | ||
16°C | 5 Hours | 8 Hours | ||
30°C | 2 Hours | 3 Hours |
- These times are based on 40 microns dry film thickness. Excessive film thickness or inadequate ventilation conditions after application require longer dry times and will cause premature failure in extreme cases
- Final cure: To obtain optimum properties, Carboline 4674 must be cured at temperatures of 177 – 232ºC. Allow for initial increase of temperature to proceed slowly up to 177ºC over a 6 hours period
Surface Preparation
Preparation | |
---|---|
General: |
Surface must be clean and dry Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating |
Steel: | Abrasive blast cleaning to Sa 2½ (ISO 8501-1) is recommended with a blast profile of 25 – 40 µm |
Aluminium: | Sweep blast cleaning (SSPC-SP16) is recommended |
Stainless Steel: | Sweep blast cleaning (SSPC-SP16) is recommended |
Application Methods
Product Information | |
---|---|
Mixing: |
Power mix to uniform consistency Avoid excessive air entrapment |
Thinning: |
May be thinned up to 12% with Carboline Thinner 10 Use of thinners other than those supplied or approved by Carboline may adversely affect product performance and void product warranty, whether expressed or implied |
Conventional Spray: | Pressure pot equipped with dual regulators, 3/8” I.D., minimum material hose .043” I.D. fluid tip and appropriate air cap |
Airless Spray: |
Pump ratio: 30 : 1 (min.) GMP Output: 3.0 (min.) Material Hose: 3/8” I.D. (min.) Tip Size: .013-.015” Output PSI: 2200 Filter Size: 60 mesh |
Brush: |
For small areas and touch-up only Use a medium natural bristle brush applying full strokes, avoid re-brushing |
Roller: | Application by roller is not recommended |
Application Conditions
Conditions | ||||
---|---|---|---|---|
Condition | Material | Surface | Ambient | Humidity |
Minimum | 4°C | 4°C | 4°C | 0% |
Maximum | 38°C | 54°C | 54°C | 95% |
- Industry standards are for substrate temperatures to be 3ºC above the dew point
- Special application techniques may be required above or below normal application conditions
Health and Safety
Clean Up
- Use Thinner 2
- In case of spillage, absorb and dispose of in accordance with local applicable regulations
Safety
- Read and follow all caution statements on this product data sheet and on the MSDS for this product
- Employ normal workmanlike safety precautions
- Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands, and all exposed areas
Ventilation
- When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
- The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
Caution
- This product contains flammable solvents
- Keep away from sparks and open flames
- All electrical equipment and installations should be made and grounded in accordance with regulations
- In areas where explosion hazards exist, workmen should be required to use non-ferrous tools and wear conductive and non-sparking shoes
- Refer to the product data sheet and safety data sheet in the attachments section above for further details
Data sheet
- Manufacturer
- Carboline
- Water / Solvent Based
- Solvent
- For Use On
- Steel, Stainless Steel, Aluminium
- Application Method
- Spray, Airless Spray, Brush
- Sheen
- Gloss
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Coverage
- 11,2 m²/l at 40 µm
- Recommended Thinner/Cleaner
- Carboline Thinner 10
- Max. Application Temperature
- Material: 38°C, Surface: 54°C, Ambient: 54°C, Humidity: 95%
- Min. Application Temperature
- Material: 4°C, Surface: 4°C, Ambient: 4°C, Humidity: 0%
- Solids by Volume
- 45 ± 2%
- Heat Resistance (up-to)
- Continuous: 400°C (752°F), Non-Continuous: 540°C (1004°F)
- Shelf Life (from date of manufacture)
- 2 years at 24ºC
- Recommended Dry Film Thickness
- 30 - 80 microns (1.18 - 3.15 mils) per coat
- Recommended Wet Film Thickness
- 65 - 175 µm per coat, normally 90 µm
- UN Number
- UN1263
- Fully Cured
- 10°C: 10 Hours, 16°C: 8 Hours, 30°C: 3 Hours
- Base Type
- Solvent-Based Silicone
- Suitable For Use On
- Aluminium
- Suitable For Use On
- Stainless Steel
- Suitable For Use On
- Steel
- Finish
- Gloss
- Application Method
- Brush
- Application Method
- Spray
- Product Usage Type
- High Temperature Coating
- Product Range
- Thermaline
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Carboline Thermaline 4674 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Carboline Carbozinc 11
Carboline Carbozinc 11 is a two-component, corrosion resistant primer that protects steel galvanically in the harshest environments. Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces Rapid cure. Dry to handle in 45 minutes at 16°C and 50% relative humidity Low temperature cure down to -18°C High zinc...
Carboline Thinner 10
Carboline Thinner 10 is a thinner for use in industrial coatings.
Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...