- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Tor QD High Build Phosphate Primer, a quick drying high build anti-corrosive primer for blast cleaned or mechanically cleaned mild steel. Applied by spraying, the primer is touch dry in 1 hour and hard dry in 4 hours.
- Anti-corrosion protection for cleaned mild steel
- An alkyd resin binder with zinc phosphate anti-corrosive pigment, together with inert inorganic pigments and thinned with a blend of xylene and aromatic hydrocarbon solvents
- Up to 6 square metres per litre
- Not suitable for overcoating with 2 pack products
- Refer below for more product information and instructions for application and preparation
Description
Tor QD High Build Phosphate Primer is a quick drying high build anti-corrosive primer for blast cleaned or mechanically cleaned mild steel. Applied by spraying, the primer is touch dry in 1 hour and hard dry in 4 hours.
Features & Benefits
- Anti-corrosion primer for mild steel
- Quick drying - touch dry in 1 hour, hard dry in 4 hours
- Applied by spray
- Smaller areas can be applied by brush
- Brush application will only produce approximately half the recommended film thickness
- Not suitable for overcoating with 2 pack products
- Theoretical coverage of up to 6 square metres per litre
- Refer below for more product information and instructions for application and preparation
Product Information
An alkyd resin binder with zinc phosphate anti-corrosive pigment, together with inert inorganic pigments and thinned with a blend of xylene and aromatic hydrocarbon solvents.
| Product reference | AK636 |
| Volume solids | 45% |
| Typical thickness | 75 microns dft from 167 microns wet |
| Theoretical coverage | 6 square metres per litre |
| Practical coverage | Reduce theoretical coverage by up to 20% |
| Colour range | Grey |
| VOC content | EU limit value for this product (cat A/i): 500 g/l . This product contains max 500 g/l VOC |
Surface Preparation
Steel:
Grit blast to BS4232, 2nd Quality (SA 2.5 Swedish Standard) with a blast profile of 50-75 microns to remove all scale, rust, old paint and contaminants.
Minimum – chip scrape and mechanically wire brush to Swedish Standard ST2 for mechanically cleaned steel.
Application Details
| Mix ratio | N/A |
| Method of application | Airless spray (tip size 0.019”-0.021” and 2000-2400 psi atomising pressure) Small areas can be brushed, two coats may be necessary to achieve the dry film thickness quoted. |
| Thinner | Thinning may render product VOC non-compliant. |
| Cleaner | Tor TH25 |
| Pot Life | N/A |
Drying Times
| Substrate Temperature | Touch Dry | Hard Dry | Overcoating Interval | |
|---|---|---|---|---|
| Minimum | Maximum | |||
| 20ºC | 1 hour | 4 hours | 4 hours | 3 months |
Note: Drying/curing times will be shortened by higher temperatures and lengthened by lower temperatures
Storage and Handling
Flash Point
- 23ºC
Limitations
Not suitable for overcoating with 2 pack products.
Brush application will only produce approximately half the recommended film thickness.
Product Details
4027-503838
Data sheet
- Manufacturer
- Tor
- Water / Solvent Based
- Solvent
- For Use On
- Steel
- Application Method
- Spray
- Sheen
- Matt
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Mixing Ratio
- -
- Suitable Substrates
- Blast cleaned or mechanically cleaned mild steel
- Key Features
- Anti-corrosion primer
- Touch Dry (at 20°C)
- 1 hour
- Dry to Handle (at 20°C)
- -
- Dry to Recoat (at 20°C)
- 4 hours
- Fully Cured (at 20°C)
- 4 hours
- Pot Life (at 20°C)
- -
- Coverage
- Theoretical coverage: 6 square metres per litre; Practical coverage: Reduce theoretical coverage by up to 20%
- Recommended Thinner/Cleaner
- Tor TH25
- Unit Contents
- -
- Compatible Primers
- -
- Compatible Topcoats
- -
- Max. Application Temperature
- -
- Min. Application Temperature
- -
- Density
- -
- Solids by Volume
- 45%
- Heat Resistance (up-to)
- -
- VOC
- 500 g/l VOC
- Shelf Life (Once Opened)
- -
- UN Number
- UN 1263
- Base Type
- Solvent-Based
- Base Type
- Alkyd
- Suitable For Use On
- Steel
- Finish
- Matt
- Application Method
- Spray
- Usages
- High Build
- Usages
- Quick Drying
- Usages
- Atmospheric
- Usages
- Anti-Corrosive
- Usages
- Zinc Phosphate
- Product Usage Type
- Primer
- Product Range
- Tor Industrial
- Colour Family
- Grey
- Dry to Recoat (@ 20-25°C)
- 4 hours
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tor QD High Build Phosphate Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
Tor HF Aromatic Thinners
We no longer stock this product, but can recommend Tor QD Thinner as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option...
In stock
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Price
£26.45
(incl. VAT)
In Stock and Available for Delivery