- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
Tor Quick Drying Machinery Enamel finishes factory machinery, tools, agricultural implements, etc, applying by airless spray.
- Available in over 2,400+ colours from RAL and BS
- 1L only available in colours mixed on a TR base - full colour selection for 5L size
- Quick drying
- Touch dry in 30 minutes
- Hard dry after 2 hours
- An alkyd resin binder pigmented with inorganic pigments and thinned with xylene
- Use with a suitable primer, such as Tor QD High Build Phosphate Primer AK636, where necessary
- Refer below for more product information, preparation and application instructions
Product customisation
Don't forget to save your customization to be able to add to cartTor Quick Drying Machinery Enamel, for the finishing of factory machinery, tools, agricultural implements, etc. Apply with an airless spray, whilst smaller areas can be brushed. The enamel dries to the touch in approx. 30 minutes, hard dry after 2 hours, and is available in over 2,400 colours from RAL and BS ranges.
Features & Benefits
- Gloss enamel finish for machinery
- Factory machines
- Tools
- Agricultural implements
- Quick drying
- Touch dry in 30 minutes
- Hard dry after 2 hours
- Use with a suitable primer, such as Tor QD High Build Phosphate Primer AK636, where necessary
- Available in over 2,400+ colours from RAL and BS
- Refer below for more product information, preparation and application instructions
Product Information
An alkyd resin binder pigmented with inorganic pigments and thinned with xylene.
Product reference | AK717 |
Volume solids | Approx 45% |
Typical thickness | 38 microns dft from 85 microns wet |
Theoretical coverage | 11.75 square metres per litre |
Practical coverage | Reduce theoretical coverage by up to 20% |
VOC content | EU limit value for this product (cat A/i): 500 g/l. This product contains max 500 g/l VOC |
Surface Preparation
Surfaces must be clean, dry, free from visible rust etc. Abrade surfaces to promote adhesion. Apply suitable primer (eg. Tor QD High Build Phosphate Primer AK636) where necessary.
Application Details
Mix ratio | N/A |
Method of application | Brush (small areas), airless spray |
Cleaner | Tor TH19 for cleaning equipment |
Pot Life | N/A |
Drying Times
Substrate Temperature | Touch Dry | Hard Dry | Overcoating Interval | |
---|---|---|---|---|
Minimum | Maximum | |||
20°C | 30 minutes | 2 hours | 1 hour | 7 days |
Note: Drying/curing times will be shortened by higher temperatures and lengthened by lower temperatures
Storage and Handling
Store the closed containers in a store room which is either in a safe place or is a fire resisting structure. The storage and conditions must meet the statutory requirements of The Highly Flammable Liquids and Petroleum Gases Regulations 1972.
Flash point
- In a range 23°C-32°C
Shelf life
- 2 years in unopened containers
Limitations
Do not use when surface to be painted is less than 2°C above the dew point.
Brushing only suitable for small areas.
- Avoid skin and eye contact i.e. wear gloves, goggles, etc
- Ensure good ventilation, mechanical if necessary
- Store and use away from heat and flame
- Do not eat or smoke in the vicinity of work
- Wash hands before eating
- Refer to supply container for additional warning labels
Data sheet
- Manufacturer
- Tor Coatings
- Water / Solvent Based
- Solvent
- For Use On
- Metal
- Sheen
- Gloss
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Pack Size
- 1L, 5L
- Parts
- 1
- Base Type
- Solvent
- Solvent
- An alkyd resin binder pigmented with inorganic pigments and thinned with xylene.
- Mixing Ratio
- -
- Suitable Substrates
- Suitably primed metals
- Key Features
- Quick drying enamel for the finishing of factory machinery, tools, agricultural implements etc.
- Application
- Spray
- Touch Dry (at 20°C)
- 30 Mins
- Dry to Recoat (at 20°C)
- 1 hour
- Fully Cured (at 20°C)
- 2 hours
- Pot Life (at 20°C)
- -
- Coverage
- 11.75 square metres per litre
- Recommended Thinner/Cleaner
- Tor TH19 for cleaning equipment
- Unit Contents
- -
- Compatible Primers
- -
- Compatible Topcoats
- -
- Max. Application Temperature
- -
- Min. Application Temperature
- -
- Density
- -
- Solids by Volume
- Approx 45%
- Heat Resistance (up-to)
- -
- VOC
- This product contains max 500 g/l VOC
- Shelf Life (from date of manufacture)
- 2 years in unopened containers
- UN Number
- UN 1263
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal
- Suitable For Use On
- Primed Surfaces
- Finish
- Gloss
- Application Method
- Spray
- Usages
- Atmospheric
- Product Usage Type
- Topcoat
- Product Range
- Tor Industrial
- Colour Family
- Neutral
- Colour Family
- Anthracite Grey
- Colour Family
- Violet
- Colour Family
- Cream
- Colour Family
- Beige
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Off-White
- Colour Family
- Black
- Colour Family
- White
- Product Type
- Acrylic
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 30 mins
- Product Attributes
- High Solids
- Product Attributes
- Gloss Retention
- Product Attributes
- Colour Retention
- Product Attributes
- Easy to Clean
- Product Attributes
- Tough / Durable
- Product Attributes
- Non-Chalking
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Tor Quick Drying Machinery Enamel is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT