Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.

Should you require training, visit - https://www.safeusediisocyanates.eu/

ResuDeck RBS (formerly Resubind CP) is a 3 component, non-pigmented, solvent-free polyurethane binder designed for car park decks, walkways and driveways. Resubind CP is designed for surface dressing with aggregates to create non-slip, hard wearing, textured floor finishes. ResuDeck RBS systems can be used in interior or exterior car park decks on a variety of substrates to provide high wear resistant anti-slip finishes.

Features & Benefits

• Non-pigmented, solvent-free polyurethane binder
• 3 component
• Excellent slip resistant textured finish
• Extremely hard wearing
• Different aggregates can be used to create various profiles
• High bond strength
• Will cure at temperatures down to 5°c
• Easy and fast to apply
• VOC Free
• Recommended uses:
• Intermediate Car Park Decks
• Top Car Park Decks
• Underground Car Park Decks
• Walkways around buildings and factories
• Theme Parks
• Public Pathways
• Public concourse areas
• Loading Bays
• Demarcation of non-slip areas

Product Information

Products required for this system

• Primer : Resuprime PU
• System : ResuDeck RBS

Preparation

New Concrete Floors:

New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.

Existing Concrete Floors:

Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and make sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuscreed PA.

Existing Floors ( previously coated )

All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. if the old resin flooring cannot be removed, then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with existing floor coating.

Priming

Open and porous substrates will require priming with Resuprime PU, on dry substrates only with less than 75% ERH reading.

Where the Relative Humidity of a substrate exceeds 75% ERH Resuprime MVT should be specified and selected on the basis of hygrometer readings in accordance with BS 8203. The number of coats to be applied is chosen in accordance with the following table.

For further information please refer to individual product data sheets.

Application

The ambient temperatures of the areas should not be allowed to fall below 10°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 5°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to installation.

Pre-mix the base component to a uniform colour, then mix the entire contents of base with the hardener. If a separate mixing bucket is being used, ensure all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately one to two minutes until the two components have fully combined then add the aggregate slowly. Mix for a further 1-2 minutes until the aggregate has fully combined and there are no lumps.

The mixed unit should be applied immediately with a squeegee or pin rake. This is best achieved by the application of smooth even pressure with the compound poured over the correct coverage rate after fixing the stop ends to control the flow of the material. Then roll the area with a spiked roller to achieve an even smooth surface and remove entrapped air. Do not re-roll the area later than 10 mins after application. The surface should then be dressed with the selected aggregate at a rate of approximately 2-3 Kg/m².

The surface should be protected from temperatures of less than 5°C and moisture in the early stages of cure. This could adversely affect the flow, levelling and surface finish of ResuDeck RBS.