- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
A single pack bio-degradable detergent wash, for the efficient removal of dirt, oil or grease prior to painting. Specially formulated for use with ViterClad cladding coatings.
- Specifically recommended for cleaning Plastisol or other sheeting prior to coating with ViterClad systems
- Effective for cleaning aged coatings or bare substrates of oil, grease or dirt prior to coating
- A bio-degradable product which after application can be washed away through domestic drainage with sufficient clean water diluent
- Concentrated – can be diluted up to 20:1 with water
Axalta ViterClene ‘C’ Degreasing Solution, a single pack bio-degradable detergent wash, for the efficient removal of dirt, oil or grease prior to painting. Specially formulated for use with ViterClad cladding coatings.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected]
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Specifically recommended for cleaning Plastisol or other sheeting prior to coating with ViterClad systems
- For the cleaning of aged coatings or bare substrates of oil, grease or dirt prior to coating.
- Bio-degradable product which after application can be washed away through domestic drainage with sufficient clean water diluent.
- An effective degreaser for galvanising.
- Concentrated – can be diluted up to 20:1 with water.
- Can be applied by brush, or airless spray.
Product Specification
Technical Data | |
---|---|
Volume Solids | n/a |
VOC Content | 417 + 20 g/litre |
SG | 0.96-0.98 kg/lt |
Storage Conditions | Store in dry, cool conditions and protect from frost. |
Shelf Life | Minimum 12 months if stored as above in unopened containers. |
Flash Point | 23-60℃ |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |
Minimum | n/a | n/a | 15 m² /litre² |
Maximum | n/a | n/a | |
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. |
Drying Times
Temperature | |||
---|---|---|---|
10℃ | 23℃ | 35℃ | |
Drying Time: | Allow 10 - 15 minutes, then flush with water. |
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Surface Preparation
Remove thick films of grease with a scraper or rags prior to application of ViterClene ‘C’.
Mixing
Ensure solution is homogenous before use.
Thinner
Clean water.
Clean water can also be used to clean equpment.
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying.
- Do not apply when rain, mist, sleet or snow are imminent.
- During application and drying time of the wash solution, the Relative Humidity should not exceed 88% and the steel temperature should remain at least 2℃ above the dew point.
Application Methods
Method | Airless Spray | Conventional Spray | Brush | Roller |
---|---|---|---|---|
Yes | No | Yes | No |
Any areas of stubborn contamination should be removed by vigorous application using e.g. brushes or clean rags, followed by thorough rinsing and allowing to dry. Ensure that all traces of contamination and residues are thoroughly removed before applying any coatings.
- Apply by brush or clean rags (recommended), or by airless spray.
- Apply ViterClene ‘C’ in accordance with the dilution described below, preferably using warm water rather than cold water. Allow 10 – 15 minutes for penetration, then water wash with potable water (pressure washing or rinsing with scrubbing is recommended) to remove all residues, and allow to dry before applying any coating.
- Any areas of stubborn contamination should be removed by vigorous application using e.g. brushes or clean rags, followed by thorough rinsing and allowing to dry. Ensure that all traces of contamination and residues are thoroughly removed before applying any coatings.
- Reduce dilution as necessary in accordance with surface conditions.
Dilution:
- Heavy soiling – apply neat
- Medium soiling (light oil, grease, general dirt) - dilute 5:1 with clean water
- Light soiling (hydraulic oils, light grease) - dilute 10:1 with clean water
- General cleaning (light dirt only) - dilute 20:1 with clean water
Product Notes
In any cleaning operation, the aim is to remove dirt from the surface. This can be achieved by loosening the dirt and washing it away with e.g. a water spray, hose pipe, etc., or by wiping it off the surface with rags, which will need changing frequently for fresh, clean ones. Using the same piece of rag or brush repeatedly without rinsing can result in the dirt simply being redistributed around the surface, and not removed.
Health & Safety
Containers are provided with safety labels which should be observed. Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets. A Safety Data Sheet for this product is available on request from Axalta Coating Systems or on our attachments section above.
Data sheet
- Manufacturer
- Axalta Coating Systems
- Application Method
- Brush, Airless Spray, Rag
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Parts
- Single part pack
- Dry to Handle (at 20°C)
- 10 – 15 minutes, then flush with water. Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation
- Coverage
- 15m² per litre
- Recommended Thinner/Cleaner
- Clean water
- Max. Application Temperature
- Relative Humidity should not exceed 88%
- Min. Application Temperature
- Steel temperature should remain at least 2℃
- Min. Application Temperature
- Steel temperature should remain at least 2℃ above the dew point.
- VOC
- 417 + 20 g/litre
- Shelf Life (from date of manufacture)
- Minimum 12 months if stored as above in unopened containers
- Recommended Dry Film Thickness
- N/A
- Recommended Wet Film Thickness
- N/A
- UN Number
- Not regulated
- Suitable For Use On
- Plastisol
- Application Method
- Brush
- Application Method
- Spray
- Application Method
- Cloth
- Product Usage Type
- Degreaser
- Categorised As
- Cladding Cleaners
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta ViterClene C Degreasing Solution is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT