- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
High performance 2 pack polyurethane metallic finish specially designed and tested for the maintenance repainting of architectural cladding.
- Up to 15 years expected system lifetime (depending on exposed environment and shade)
- Suitable for urban, marine and industrial environments
- Tough, durable finish combining abrasion resistance with outstanding colour and sheen retention
- Cures at sub-zero temperatures and has good climatic tolerance
- Note: this product has a minimum order quantity of 400 litres; for smaller orders we can recommend Tikkurila Temadur 50 (in RAL 9006)
- Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Should you require training, visit - https://www.safeusediisocyanates.eu/
Axalta ViterClad M50 Finish is a two pack recoatable polyurethane finish with a metallic finish, specially formulated for the maintenance and repainting of architectural cladding. Recommended for the maintenance of Corus Colorcoat HP200 and HPS200 cladding, it has an expected system lifetime up to 15 years (depending on exposed environment and shade) and is suitable for PVF2, Silicone Polyester and Polyester Cladding (when applied over ViterClad Bonding Coat) in urban, marine and industrial environments.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Mixing
- Thinner
- Application Conditions
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Recommended for the maintenance of Corus Colorcoat HP200 and HPS200 cladding
- Expected system lifetime up to 15 years (depending on exposed environment and shade)
- Suitable for PVF2, Silicone Polyester and Polyester Cladding when applied over ViterClad Bonding Coat
- Suitable for urban, marine and industrial environments
- Tough, durable finish combining abrasion resistance with outstanding colour and sheen retention
- Good cleaning properties for ease of building maintenance
- Cures at sub-zero temperatures and has good climatic tolerance
- Tolerant of slight surface moisture during application
Product Specification
Technical Data | |
---|---|
Volume Solids | 42 ± 2% (may vary with colour) |
VOC Content | 471 + 20 g/litre (varies with colour) |
SG | 1.06-1.08 kg/lt mixed, varies with colour |
Storage Conditions | Store in dry, cool conditions and protect from frost |
Shelf Life | Minimum 12 months if stored as above in unopened containers |
Flash Point | 23-60℃ |
Film Thickness Range And Coverage
Product Data | |||||
---|---|---|---|---|---|
Dry Film Thickness | Wet Film Thickness | Theoretical Coverage | |||
Minimum | 25 µm | 60 µm | 16.8 m² /litre | ||
Maximum | 60 µm | 143 µm | 7.0 m² /litre | ||
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated |
Drying Times
Product Data | ||||||
---|---|---|---|---|---|---|
Applied to 125 microns DFT | 5℃ | 10℃ | 23℃ | 35℃ | ||
Dust Free | 3 hr | 2 hr | 1 hr | 45 min | ||
Hard Dry | 9 hr | 6 hr | 3 hr | 2 hr | ||
Overcoating | Minimum | 24 hr | 4 hr | 12 hr | 10 hr | |
Maximum | Indefinite if clean and sound and sound | |||||
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation |
Surface Preparation
- This product is a finish coat which should be applied over ViterClad Bonding Coat or suitably prepared, sound Plastisol for recolour work
- For aged/degraded Plastisol, condition diagnosis and correct surface preparation are critical to performance. Please consult Rawlins Technical Team for individual project specifications
- Completely new and unweathered HP200* Plastisol must be wiped with white spirit (1050 Thinner) and allowed to dry prior to applying ViterClad 50
- New HPS200* Plastisol must be wiped with xylene (1006 Thinner) and allowed to dry prior to applying ViterClad 50
- For PVF2, Silicone Polyester and other cladding types, refer to Rawlins Technical Team 0113 2455450 (option 2) or [email protected]
- Surfaces should be clean, dry and free from all grease, oil and general contamination
Mixing
Mix only in the proportions stated, mixing each component individually then together using a mechanical agitator. Agitate periodically during use to ensure product remains homogeneous
Thinner
1737 Thinner
Equipment Cleaner - 1737 Thinner
Application Conditions
- Only apply in conditions of good ventilation which must be maintained during drying and curing.
- Do not apply in windy conditions where wind is likely to carry spray mist.
- Do not apply when rain, mist, sleet or snow are imminent.
- During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3ºC above the dew point.
- Only apply this product when the above conditions can be maintained throughout the critical application and drying/curing process.
- Paint temperature should ideally be at a minimum of 15ºC.
- Do not apply above 40ºC.
- Do not apply over standing or running water or ice.
Application Methods
- Airless Spray: recommended for best finish. Output fluid pressure at tip 2000- 2500 psi, Tip Size: 11-13 thou (0.33-0.43mm). Up to 5% 1737 Thinner may be added for application under cool or hot conditions, but thinning should be avoided if possible
- Conventional spray is possible but not recommended
- Brush – not recommended due to metallic finish
- Roller – use only good quality short hair roller types of suitable width to accommodate the cladding profile and configuration – always work from a wet edge. Up to 10% thinner may be required – use 1048 Thinner when applying by roller in warm conditions. Axalta Coating Systems strongly recommend that a feasibility test area is applied to confirm acceptable aesthetics are achievable
Product Notes
- Contains isocyanates – refer to Safety Data Sheet
- This coating has not been tested to the standard of the new regulation 7(2) of the Building Regulations 2010, which came into force in Dec 2018
Health & Safety
Containers are provided with safety labels which should be observed. Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets - these sheets can be found in the attachments section above.
Data sheet
- Manufacturer
- Axalta
- For Use By
- Professional Use
- For Use On
- PVF2, Silicone Polyester, Plastisol
- Application Method
- Brush, Roller, Spray
- Sheen
- Semi-Gloss
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5L
- Parts
- 2
- Mixing Ratio
- Base - 8 parts by volume. Hardener - 1 part by volume
- Application
- Brush, Roller, Spray
- Touch Dry (at 20°C)
- 1 hr
- Dry to Recoat (at 20°C)
- 3 hr
- Fully Cured (at 20°C)
- 12 hr
- Coverage
- 7.0 to 16.8 m2 /litre (see data sheet)
- Max. Application Temperature
- 40ºC
- Min. Application Temperature
- 15ºC
- VOC
- 471 + 20 g/litre (varies with colour)
- Shelf Life (from date of manufacture)
- Minimum 12 months if stored as above in unopened containers
- Touch Dry
- 1 Hour
- Recommended Dry Film Thickness
- Min: 25 µm - Max: 60 µm
- Recommended Wet Film Thickness
- Min: 60 µm - Max: 143 µm
- UN Number (Activator)
- UN1263
- UN Number (Base)
- UN1263
- Base Type
- Polyurethane
- Suitable For Use On
- Cladding
- Suitable For Use On
- Marine Application
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Product Usage Type
- Topcoat
- Colour Family
- Metallic
- Colour Family
- Aluminium
- Categorised As
- Metal & Plastisol Cladding Paint
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Axalta ViterClad M50 Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Axalta 1048 Thinner
Axalta 1048 Thinner, for use with the Axalta range of coatings, is a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistancy for application whether it be for brush, roller or spray. Can also be used for the cleaning of some surfaces prior to application of the coating...
Axalta 1737 Thinner
Axalta 1737 Thinner, for use with the Axalta range of coatings, is a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistancy for application whether it be for Brush, Roller or Spray. It can also be used for the cleaning of some surfaces prior to application of the coating...
Axalta 1006 Thinner
We no longer stock this product, but can recommend Axalta Thinner Fast Industrial (TH120) as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team...