Follow us on:

HMG D66 Chassis Black | Automotive & Metal Topcoat

HMG D66 Chassis Black

TOPCSS
HMG4363

HMG D66 Chassis Black is an alkyd based synthetic enamel to suit both brush and spray requirements.

  • Good performance
  • Oil and diesel resistant
Colour
Size
Finish
£67.60(incl. VAT)
£56.33(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG D66 Chassis Black is an alkyd based synthetic enamel to suit both brush and spray requirements.



Click To Jump To Section:




Features & Benefits


  • Good performance
  • Oil and diesel resistant



Product Specification


Technical Data
Volume Solids: 50.1%
VOC Content: 0.65kgs/lt
SG: 0.98
Viscosity: 240 mPas
Density: 0.912 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Flash Point: 29°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Compliant Spray Gun: 25 µm 50 µm
HVLP: 25 µm 50 µm
Brush: 25 µm 50 µm
Roller: 25 µm 50 µm



Coverage: 20 square metres per litre @ 25 microns dft

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 2 - 4 hours
Dry To Recoat: 24 hours minimum
Fully Cured: 24 hours



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.



Application Methods


Technical Data
Compliant Spray Gun HVLP Brush Roller
Mixing Ratio: Base: 1 Base: 1 Ready for use Ready for use
Thinner: approx 10% Thinner: approx 10% - -
Thinner Options: Thinner 2611 Thinner 2611 - -
Thinner 2612 Thinner 2612 - -
Viscosity: - - - -
Number Of Coats (Guide Only): 1 dust coat then 1 full coat 1 full coat - -
Flash Off: 15 minutes 15 minutes 15 minutes 15 minutes



For futher information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or



  • D66 can be brushed or hot sprayed as supplied.
  • For conventional air assisted spray up to 25% 2611 or 2612 Thinner may be added to suit equipment.



Product Notes


Information on basic physical and chemical properties
Form: Liquid
Colour: According to product specification.
Odour: Characteristic
Odour Threshold: Not determined
pH-value: Not determined
Change in Condition
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 135°C
Flash Point: 29°C
Flammability (solid, gas): Not applicable
Ignition temperature: 200°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 0.6 Vol %
Explosion limits: Upper: 7.0 Vol %
Vapour pressure at 20°C: Not determind
Density at 20°C: 0.912 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 240 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 3.8%
Solids content: 50.1%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a noncombustible container with a tight fitting lid.

Click to go back to the top of the page

Product Details
4363-605537

Data sheet

Manufacturer
HMG Paints Limited
Water / Solvent Based
Solvent
Application Method
Brush, roller, spray
Sheen
Gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
5L
Base Type
Alkyd based
Mixing Ratio
Compliant Spray Gun: Base 1 - Thinner: approx 10%
Mixing Ratio
Brush: Base 1 - Thinner: approx 10%
Key Features
Oil and diesel resistant
Touch Dry (at 20°C)
2 - 4 Hours
Dry to Recoat (at 20°C)
24 Hours minimum
Fully Cured (at 20°C)
24 Hours
Coverage
20 square metres per litre @ 25 microns dft
Density
0.912 g/cm³
Solids by Volume
50.1 %
VOC
0.65kgs/lt
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers.
Recommended Dry Film Thickness
25 µm
Recommended Wet Film Thickness
50 µm
UN Number
UN1263
Base Type
Solvent-Based
Base Type
Alkyd
Suitable For Use On
Metal
Finish
Gloss
Application Method
Brush
Application Method
Roller
Application Method
Spray
Product Usage Type
Topcoat
Product Range
D66
Colour Family
Black
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG D66 Chassis Black is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT



COVERAGE CALCULATOR
Units
Film Thickness
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

You might also like
HMG Thinner 2611

HMG Thinner 2611

HMG Thinner 2611 is a medium thinner. For use with compatible HMG systems.

Price £13.45 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
HMG Thinner 2612

HMG Thinner 2612

HMG Thinner 2612 is a slow thinner. For use with compatible HMG systems.

Price £14.09 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery