- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG SAH300 Enamel is a high solids, gloss 1K polyurethane alkyd designed for brush application.
- Excellent protection against harsh weather conditions, atmospheric pollution, road dirt, sharp cleaning agents and mechanical car washes etc
- Available in 5,000+ colours from RAL, NCS, and British Standard
- Also available as an aerosol, please see HMG SAH300 Enamel Aerosol
- Available in satin and gloss finishes; matt finish is no longer available
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartHMG SAH300 Enamel is a high solids, gloss 1K polyurethane alkyd designed for brush application.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Excellent protection against harsh weather conditions, atmospheric pollution, road dirt, sharp cleaning agents and mechanical car washes etc
- Available in 5,000+ colours from RAL, NCS, and British Standard
Recommended primer/fillier/sealer systems:
Product Specification
Technical Data | |
---|---|
Volume Solids: | 72.5% |
VOC Content: | 0.340kgs/ltr |
SG: | - |
Viscosity: | 800 mPas |
Density: | 1.112 g/cm³ |
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. |
Shelf Life: | 12 months from delivery date in original sealed containers. |
Flash Point: | 31°C |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Brush: | 50 µm | 100 µm |
Coverage: 14 square metres per litre @ 50 microns dft.
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
Drying Times At 20°C | |
---|---|
Touch Dry: | 4 - 6 hours |
Dry To Handle: | 12 hours |
Dry To Recoat: | After 12 hours |
Fully Cured: | 24 hours |
- For professional use only.
- This product was designed for brush application onto large areas. It has been developed to provide a long 'wet edge' and an extended drying time. It may not be suitable for small areas or areas that are due to be returned to service in short time-frames. HMG Coach Enamel can be used as a quicker drying alternative.
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
Application Methods
Technical Data | |||||
---|---|---|---|---|---|
Brush | |||||
Mixing Ratio: | Ready for use | ||||
- | |||||
Thinner Options: | n/a | ||||
- | |||||
Viscosity: | n/a | ||||
Number Of Coats (Guide Only): | n/a | ||||
Flash Off: | n/a |
- Properties can be enhanced by the addition of Hardener 9029. Use 10 parts base to 1 part hardener.
Product Notes
Information on basic physical and chemical properties | |
---|---|
Form: | Liquid |
Colour: | According to product specification. |
Odour: | Characteristic |
Odour Threshold: | Not determined |
pH-value: | Not determined |
Change in Condition | |
Melting point/freezing point: | Undetermined |
Initial boiling point and boiling range: | 135°C |
Flash Point: | 31°C |
Flammability (solid, gas): | Not applicable |
Ignition temperature: | 200°C |
Decomposition temperature: | Not determined. |
Auto-ignition temperature: | Product is not selfigniting |
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." |
Explosion limits: Lower: | 0.6 Vol % |
Explosion limits: Upper: | 7.0 Vol % |
Vapour pressure at 20°C: | 2.1 hPa |
Density at 20°C: | 1.112 g/cm³ |
Relative density: | Not determined |
Vapour density: | Not determined |
Evaporation rate: | Not determined |
Solubility in / Miscibility with water: | NOT MISCIBLE |
Partition coefficient: n-octanol/water: | Not determined |
Viscosity: Dynamic at 20°C: | 800 mPas |
Viscosity: Kinematic: | Not determined |
Solvent content: Organic solvents: | 27.1% |
Solids content: | 72.5% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
- Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a noncombustible container with a tight fitting lid.
Data sheet
- Manufacturer
- HMG Paints Limted
- Water / Solvent Based
- Solvent
- For Use On
- Metal
- Application Method
- Brush
- Sheen
- Gloss
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Pack Size
- 1L
2.5L
5L - Touch Dry (at 20°C)
- 4 - 6 Hours
- Dry to Handle (at 20°C)
- 12 Hours
- Dry to Recoat (at 20°C)
- After 12 Hours
- Fully Cured (at 20°C)
- 24 Hours
- Density
- 1.112 g/cm³
- Solids by Volume
- 72.5%
- VOC
- 0.340kgs/ltr
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers.
- Recommended Dry Film Thickness
- 50 µm
- Recommended Wet Film Thickness
- 100 µm
- UN Number
- UN1263
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal
- Finish
- Gloss
- Application Method
- Brush
- Product Usage Type
- Topcoat
- Product Range
- SAH300
- Colour Family
- Stone
- Colour Family
- Anthracite Grey
- Colour Family
- Beige
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Metallic
Questions
Question about the product
Jason on 2021-03-21 14:10:03 | Question:
Hi, I was wondering if this is suitable as a top coat over a zinc phosphate primer (alkyd). Also what what would be the recommended thinner? Regards, Jason |
Answer from Rawlins’ Technical Team:
We would recommend testing for compatibility and adhesion prior to full application with your primer. The manufacturers recommended primer is HMG Synthetic BDX Primer, this is also an alkyd based primer. The paint is designed for brush application and is not to be thinned. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG SAH300 Enamel is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Synthetic BDX Primer
HMG Synthetic BDX Primer is a high build, anti-corrosive, single pack alkyd primer for use under all HMG synthetic topcoats, combining high build and excellent sandability with outstanding application and scratch filling properties. For use on suitably prepared structural steel, chassis, fabrication and aluminium Can be applied to bare...
HMG Synthetic High Opacity Undercoat
HMG Synthetic High Opacity Undercoat is a 1K alkyd/polyurethane undercoat with superior brushing qualities and excellent obliteration properties. Suitable for large areas due to its ease of application and long wet edge time Please note: Colours shown are for illustrative purposes only
HMG Thinner 2612
HMG Thinner 2612 is a slow thinner. For use with compatible HMG systems.
HMG Hardener 9029 ZIP
HMG Hardener 9029 ZIP is an isocyanate hardener. Designed for use in recommended HMG Alkyd and Polyurethane Alkyd systems. Upgrades the performance characterstics of the system, including durability and time to touch dry may decrease by 10 - 20% dependant on paint system, film thickness and curing conditions.
HMG SAH300 Enamel Aerosol
HMG SAH300 Enamel Aerosol is a high solids, gloss 1K polyurethane alkyd aerosol. This product has also been designed to be “Ready for Use”, for the non-aerosol version of this product please see HMG SAH300 Enamel. 400ml/16oz Aerosol Available in packs of 1 or packs of 2-10, 40, 50, 100 and 500 with qty price breaks Available in 5,000+...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...