- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total (inc. VAT) £0.00
HMG Synthetic Fluorescent. A high quality `2 hour` synthetic alkyd fluorescent enamel.
HMG Synthetic Fluorescent is part of a three coat system:
| 3 Coat System Details | |||||
|---|---|---|---|---|---|
| Coat 1 | HMG Synthetic BDX Primer (White) | ||||
| Coat 2 | HMG Synthetic Fluorescent | ||||
| Coat 3 | Overcoat with HMG Marine Varnish to attain gloss, improve durability and help protect against UV degradation | ||||
- Part two of a three coat system
- Also available as an aerosol, please see HMG Synthetic Fluorescent Aerosol
Description
HMG Synthetic Fluorescent. A high quality '2 hour' synthetic alkyd fluorescent enamel. This product is to be used as part of a 3 coat system.
HMG Synthetic Fluorescent is part of a three coat system:
| 3 Coat System Details | |||||
|---|---|---|---|---|---|
| Coat 1 | HMG Synthetic BDX Primer (White) | ||||
| Coat 2 | HMG Synthetic Fluorescent | ||||
| Coat 3 | Overcoat with HMG Marine Varnish to attain gloss, improve durability and help protect against UV degradation | ||||
Please note more than one coat of each may be required depending on application to achieve desired results.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Part two of a three-pack system
Product Specification
| Technical Data | |
|---|---|
| Volume Solids: | 61.8% |
| VOC Content: | 0.45kgs/ltr |
| SG: | - |
| Viscosity: | 300 mPas |
| Density: | 1.018 g/cm³ |
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. |
| Shelf Life: | 12 months from delivery date in original sealed containers. |
| Flash Point: | 29°C |
Film Thickness Range And Coverage
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Brush: | 50 μm | 100 μm | |
| Compliant Spray: | 50 μm | 100 μm | |
Coverage: 10 square metres per litre @ 50 microns dft (Theoretical).
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
| Drying Times At 20°C | |
|---|---|
| Touch Dry: | 90 minutes |
| Dry To Handle: | 4 hours |
| Dry To Recoat: | After 12 hours |
| Fully Cured: | 12 hours |
Surface Preparation
Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
Application Methods
| Technical Data | |||||
|---|---|---|---|---|---|
| Brush | Compliant Spray | ||||
| Mixing Ratio: | Ready for use | Base | |||
| - | Thinner: Up to 10% | ||||
| Thinner Options: | - | 2611 | |||
| - | 2612 | ||||
| Viscosity: | Ready for use | Ready for use | |||
| Number Of Coats (Guide Only): | 2 - 4 Full Coats | 2 - 4 Full Coats | |||
| Flash Off: | - | - | |||
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Product Notes
| Information on basic physical and chemical properties | |
|---|---|
| Form: | Liquid |
| Colour: | Fluorescent Colours |
| Odour: | Characteristic |
| Odour Threshold: | Not determined |
| pH-value: | Not determined |
| Change in Condition | |
| Melting point/freezing point: | Undetermined |
| Initial boiling point and boiling range: | 135°C |
| Flash Point: | 29°C |
| Flammability (solid, gas): | Not applicable |
| Ignition temperature: | 200°C |
| Decomposition temperature: | Not determined. |
| Auto-ignition temperature: | Product is not selfigniting |
| Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." |
| Explosion limits: Lower: | 0.6 Vol % |
| Explosion limits: Upper: | 7.0 Vol % |
| Vapour pressure at 20°C: | 27 hPa |
| Density at 20°C: | 1.018 g/cm³ |
| Relative density: | Not determined |
| Vapour density: | Not determined |
| Evaporation rate: | Not determined |
| Solubility in / Miscibility with water: | NOT MISCIBLE |
| Partition coefficient: n-octanol/water: | Not determined |
| Viscosity: Dynamic at 20°C: | 300 mPas |
| Viscosity: Kinematic: | Not determined |
| Solvent content: Organic solvents: | 38.0% |
| Solids content: | 61.8% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
- Suitable respiratory equipment should be worn when spraying.
Product Details
4369-736693
Data sheet
- Manufacturer
- HMG Paints Limited
- For Use By
- Professional Use
- Water / Solvent Based
- Solvent
- For Use On
- Metal
- Application Method
- Aerosol, Spray
- Sheen
- Matt
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Single
- Pack Size
- 1L, 5L
- Mixing Ratio
- Compliant Spray: Thinner: Up to 10%
- Touch Dry (at 20°C)
- 90 Mins
- Dry to Handle (at 20°C)
- 4 Hours
- Dry to Recoat (at 20°C)
- After 12 Hours
- Fully Cured (at 20°C)
- 12 Hours
- Coverage
- 10 square metres per litre @ 50 microns dft
- Recommended Thinner/Cleaner
- Thinner 2611/2612
- Density
- 1.018 g/cm³
- Solids by Volume
- 61.8 %
- VOC
- 0.45kgs/ltr
- Recommended Dry Film Thickness
- 50 μm
- Recommended Wet Film Thickness
- 100 μm
- UN Number
- UN1263
- Base Type
- Solvent-Based
- Base Type
- Alkyd
- Suitable For Use On
- Metal
- Finish
- Matt
- Application Method
- Spray
- Application Method
- Aerosol
- Components
- 1K
- Product Usage Type
- Safety & Security
- Colour Family
- Blue
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Yellow
- Colour Family
- Green
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Synthetic Fluorescent is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
You might also like
HMG Marine Varnish
HMG Marine Varnish is a tough and durable clear gloss formulated on a unique blend of polyurethane alkyds for high quality marine and can be used for industrial finishing. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener/thinner:2-Pack System DetailsBase (Part 1) HMG...
Price£105.22 (incl. VAT)
In Stock and Available for Delivery
HMG Synthetic BDX Primer
HMG Synthetic BDX Primer is a high build, anti-corrosive, single pack alkyd primer for use under all HMG synthetic topcoats, combining high build and excellent sandability with outstanding application and scratch filling properties.For use on suitably prepared structural steel, chassis, fabrication and aluminium Can be applied to bare...
Price£19.03 (incl. VAT)
In Stock and Available for Delivery
HMG Thinner 2611
HMG Thinner 2611 is a medium thinner.For use with compatible HMG systems.
Price£13.45 (incl. VAT)
In Stock and Available for Delivery
HMG Thinner 2612
HMG Thinner 2612 is a slow thinner.For use with compatible HMG systems.
Price£14.09 (incl. VAT)
In Stock and Available for Delivery
HMG Synthetic Fluorescent Aerosol
HMG Synthetic Fluorescent Aerosol is a high quality `2 hour dry` synthetic alkyd fluorescent enamel aerosol. This product is also available in non-aerosol form, please see HMG Synthetic Fluorescent. HMG Synthetic Fluorescent Aerosol is part two of a three coat system:3 Coat System DetailsCoat 1 HMG Synthetic BDX Primer...
Price£32.75 (incl. VAT)
In Stock and Available for Delivery