- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Chlorinated Rubber is a versatile, high build, easy to apply, single pack chlorinated rubber based paint. It gives excellent durability combined with good resistance to acids, alkalis and oxidising agents in aqueous and gaseous forms.
- Available in 3,500+ colours, inc. RAL Classic, BS, NCS & the new NCS 2050 colours
- Versatile
- High build
- Easy to apply
- Single pack
- Gives excellent durability combined with good resistance to acids, alkalis and oxidising agents in aqueous and gaseous forms
- Good coverage, up to 16 square metres per litre
- Can be spray-applied as well as brushed
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartDescription
HMG Chlorinated Rubber is a versatile, high build, easy to apply, single pack chlorinated rubber based paint. It gives excellent durability combined with good resistance to acids, alkalis and oxidising agents in aqueous and gaseous forms.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Available in 3,500+ colours, inc. RAL Classic, BS, NCS & the new NCS 2050 colours
- Versatile
- High build
- Easy to apply
- Single pack
- Gives excellent durability combined with good resistance to acids, alkalis and oxidising agents in aqueous and gaseous forms
- Good coverage, up to 16 square metres per litre
- Can be spray-applied as well as brushed
Product Specification
| Technical Data | |
|---|---|
| Volume Solids: | 48.2% |
| VOC Content: | 0.500kgs/ltr |
| SG: | - |
| Viscosity: | 350 mPas |
| Density: | 1.053 g/cm³ |
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. |
| Shelf Life: | 12 months from delivery date in original sealed containers. |
| Flash Point: | 24°C |
Film Thickness Range And Coverage
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Brush: | 30 μm | 60 μm | |
| Compliant Spray: | 30 μm | 560 μm | |
| Airless/Air Assisted: | 30 μm | 60 μm | |
Coverage: 16 square metres per litre @ 30 microns dft (Theoretical).
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
| Drying Times At 20°C | |
|---|---|
| Touch Dry: | 40 minutes |
| Dry To Handle: | 6 hours |
| Dry To Recoat: | At any stage after |
| Fully Cured: | 24 hours |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
- Read and follow the safety data sheet, product data sheet and label instructions.
- Stir all paints thoroughly before use.
- Always use the same batch number on the same job.
- Check colour & sheen.
- Filter the product immediately before use.
- Reduce emissions and maintain quality by replacing tin lid after use.
Application Methods
| Technical Data | |||||
|---|---|---|---|---|---|
| Brush | Compliant Spray Gun | Airless/Air Assisted | |||
| Mixing Ratio: | Ready for use | Base: 1 | Base: 1 | ||
| - | Thinner: <10% | Thinner: <10% | |||
| Thinner Options: | - | Thinner 2621 | Thinner 2621 | ||
| - | Thinner 2622 | Thinner 2622 | |||
| Viscosity: | Ready for use | 25 - 35 seconds B4 cup | 30 - 35 seconds B4 cup | ||
| Spray Gun Setup: | - | 1.6 - 1.8 | 11 - 13 thou 40/50° | ||
| Number Of Coats (Guide Only): | 2 full coats | 2 full coats | 2 full coats | ||
| Flash Off: | 20 minutes minimum | 20 minutes minimum | 20 minutes minimum | ||
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Product Notes
| Information on basic physical and chemical properties | |
|---|---|
| Form: | Liquid |
| Colour: | According to product specification |
| Odour: | Characteristic |
| Odour Threshold: | Not determined |
| pH-value: | Not determined |
| Melting point/freezing point: | Undetermined |
| Initial boiling point and boiling range: | 130°C |
| Flash Point: | 24°C |
| Flammability (solid, gas): | Not applicable |
| Ignition temperature: | 400°C |
| Decomposition temperature: | Not determined. |
| Auto-ignition temperature: | Product is not selfigniting |
| Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." |
| Explosion limits: Lower: | 0.7 Vol % |
| Explosion limits: Upper: | 7.5 Vol % |
| Vapour pressure at 20°C: | 6.7-8.2 hPa |
| Density at 20°C: | 1.053 g/cm³ |
| Relative density: | Not determined |
| Vapour density: | Not determined |
| Evaporation rate: | Not determined |
| Solubility in / Miscibility with water: | NOT MISCIBLE |
| Partition coefficient: n-octanol/water: | Not determined |
| Viscosity: Dynamic at 20°C: | 350 mPas |
| Viscosity: Kinematic: | Not determined |
| Solvent content: Organic solvents: | 53.8% |
| Solids content: | 46.9% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
- Suitable respiratory equipment should be worn when spraying.
Product Details
4378-854141
Data sheet
- Manufacturer
- HMG Paints Limited
- Sheen
- Gloss
- Single, Two or Three Pack
- Single
- Pack Size
- 1L
2.5L
5L - Key Features
- Good resistance to acids, alkalis and oxidising agents in aqueous and gaseous forms.
- Touch Dry (at 20°C)
- 40 Minutes
- Dry to Handle (at 20°C)
- 6 Hours
- Dry to Recoat (at 20°C)
- At any stage after.
- Fully Cured (at 20°C)
- 24 Hours
- Density
- 1.053 g/cm³
- Solids by Volume
- 48.2 %
- VOC
- 0.50kgs/ltr
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers.
- Finish
- Gloss
- Size
- 1L
2.5L
5L - Recommended Dry Film Thickness
- 30 μm
- Recommended Wet Film Thickness
- 60 μm
- UN Number
- 1263
- Base Type
- Chlorinated Rubber
- Finish
- Gloss
- Application Method
- Brush
- Application Method
- Spray
- Product Usage Type
- Topcoat
- Colour Family
- Blue
- Colour Family
- Neutral
- Colour Family
- Brown
- Colour Family
- Stone
- Colour Family
- Orange
- Colour Family
- Beige
- Colour Family
- Yellow
- Colour Family
- Green
- Colour Family
- White
- Colour Family
- Red
- Colour Family
- Metallic
- Colour Family
- Pink
- Colour Family
- Anthracite Grey
- Colour Family
- Purple
- Colour Family
- Grey
- Colour Family
- Black
 Clark Ewing on 2024-09-11 14:42:16 | Question:
Could I use this product to waterproof inside of drawers on my sink unit? |
Answer from Rawlins’ Technical Team:
Thank you for the enquiry, we would need to ask for more information to assist with a specification. Please contact [email protected] | |
| Katherine on 2024-08-21 10:20:26 | Question:
Hi, is this paint waterproof and can it be used on brick to prevent penetrating damp? Thanks Katherine |
Answer from Rawlins’ Technical Team:
Assuming the damp wall is located in a basement, this product wouldn't be suitable. However, as an alternative you could consider Coo-Var Anti-Damp Paint, this is designed as a primer coat containing an active reagent which combines with surface moisture and dampness, and can be appleid to surfaces still slightly damp. This product can also be over-coated for decorative or aesthetic finishes. | |
| Danny on 2024-07-31 15:38:10 | Question:
Can I use this product on butyle lining of my swimming pool. |
Answer from Rawlins’ Technical Team:
Although this product wouldn't be recommended for this type of application, due to being quite flexible and smooth,and the potential to cause difficulty in adhereing to rubber lining substrates, HMG have advised assuming the lining is prepared as detailed in the technical datasheet, to apply a small amount to a test area to check for adhesion and compatibility firstly, with a view to over-coating the rest of the lining. | |
| Declan on 2023-07-07 21:23:16 | Question:
Hi, Considering using hmg chlorinated rubber, any recommended spraygun setup? I will be spraying it on sponges to make them more hygienic. Thanks for any help you can give. |
Answer from Rawlins’ Technical Team:
HMG recommends for compliant spray gun application a 1.6 to 1.8mm fluid tip and 11 to 13 thou 40/50 for air assisted. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Chlorinated Rubber is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
HMG Thinner 2621
HMG Thinner 2621 is a thinner for use in various applications. For use with compatible HMG systems.
Price
£13.45
(incl. VAT)
In Stock and Available for Delivery
HMG Thinner 2622
HMG Thinner 2622 is a slow thinner. For use with compatible HMG systems.
Price
£47.78
(incl. VAT)
In Stock and Available for Delivery
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Price
£25.93
(incl. VAT)
In Stock and Available for Delivery