Envirogard Smart Strip Pro Paint Remover (formerly Dumond Smart Strip PRO) Professional Strength Paint Remover effectively removes 2-component, high-performance coatings and lead paint.

Formulated without methylene chloride, is non-carcinogenic, non- caustic, and non-flammable, this water-based paint remover will effectively remove multiple coats of oil-based, water-based, acrylics, varnishes, epoxies, urethanes, elastomeric and lead paint from most interior or exterior surfaces (wood, brick, stone, concrete, plaster, metal, most plastic, most glass and fiberglass).

Envirogard Smart Strip Pro Paint Remover Professional Strength Paint Remover delivers the superior performance professionals are looking for when removing even the most difficult coatings, being user-friendly, biodegradable, low odour, low VOC and does not require neutralization. It can be used with or without the Envirogard Smart Strip Protective Wrap (Formerly Dumond Laminated Paper), however, efficacy is enhanced and the dwell-time is extended when used.

Quick Links - Click To Jump To Section:

• Features & Benefits
• Limitations
• Test Patch
• Recommended Substrates
• Preparation
• Surface and Air Temperatures
• Application & Spread Rate
• Spray Application
• Removal & Clean Up
• Best Practices:
• WARNING

Features & Benefits

• Delivers superior performance for professionals
• Effectively removes 2-component, high-performance coatings and lead paint
• Ideal for historic restoration, lead abatement, marine and industrial projects
• Removes up to 20 coats in one application
• Water-based, low VOC formulation, non-carcinogenic
• Does not contain methylene chloride or caustic chemicals
• Easy brush, roll, trowel, or airless spray application
• Suitable for interior and exterior applications
• User-friendly and biodegradable
• Does not require neutralization
• Can be used with Envirogard Smart Strip Protective Wrap for enhanced efficacy and extended dwell-time
• Effectively removes 2-component, high-performance coatings and lead paints, including:
  • Wood
  • Brick
  • Stone
  • Concrete
  • Plaster
  • Metal
  • Most plastic
  • Most glass
  • Fibreglass
• Multiple coats of oil-based
• Water-based
• Acrylics
• Varnishes
• Epoxies
• Urethanes
• Elastomeric
• Lead paint from most interior or exterior surfaces:

Limitations

No recommended for use on:

• Glass
• Plastics
• Vinyl
• Most fiberglass
• Plexiglass
• Drywall
• Polished limestone
• Marble or granite
• Composite decking
• EIFS
• MDF
• OSB
• Some laminates
• Veneers
• Rubber

Test Patch

Always perform a small inconspicuous test area on each type of substrate and paint coating prior to full application. Testing before beginning any project is the best way to ensure product effectiveness. Test patches can determine the proper dwell time and thickness to apply the product for your specific application. Failure to do a test patch can result in need for more than one application, increasing labour and material costs.

Recommended Substrates

Before applying to the entire substrate, always do a test patch. Recommended for use on:

• Wood
• Brick
• Concrete
• Steel
• Aluminium
• Asphalt
• Unpolished stones
• Copper
• Tile
• Terra cotta
• Cement clapboard
• Slate surfaces

Ideal for a wide use of residential, commercial and industrial applications, delivering superior performance demanded on historic restoration and lead abatement projects without damaging the surface being stripped - can also be used to remove flooring adhesives and mastics.

Preparation

Be sure that the surface is clean, dry and dull before beginning your project.

Protect and cover all areas such as vegetation and other surfaces not designated to be stripped including adjoining surfaces where overspray and rinse water may travel.

Solvent-resistant polyethylene sheets can be used as an effective barrier. Wet down all vegetation before beginning and cover with 6 mil solvent resistant polyethylene sheeting.

Be careful not to lay sheeting on vegetation in the sun or it may result in killing the foliage.

Surface and Air Temperatures

To avoid product from freezing and reducing effectiveness do not use below 35°F (approx. 2℃).

For best results, use product in temperatures above 50°F (approx. 10℃) and below 90°F (approx. 32℃). Product effectiveness is increased in warmer temperatures.

Application & Spread Rate

Envorogard always recommends working in smaller manageable areas when stripping unless you are working with many people.

Using a trowel, brush, roller or airless paint sprayer, apply paste no less than a 1/8” according to test patch results. For a 24- hour dwell time ¼ inch is recommended.

When applying onto irregular surfaces use a nylon brush to force paste into intricate areas.

Product can dwell between 3-24 hours if necessary.

Smart Strip PRO Paint Remover provides an average spread rate of approximately 40-50 Sq. Ft. per gallon; results may vary based on substrate texture and porosity.

Spray Application

Envirogard recommends that Smart Strip PRO be sprayed with an airless paint sprayer.

The sprayer pump size should be at least 1 gallon per minute and all gun and manifold filters should be removed prior to spraying. Hose size should be a new 1/4" ID, however a 3/8" ID hose will reduce strain on the sprayer. It is always recommended to use a new hose on the job, as old paint in the lines will dislodge and cause clogs during application.

Keep a clean bucket of water available, as an occasional flush of the pump may be necessary on hot days to alleviate clogs and the pumps inability to build up pressure.

Do not leave Smart Strip PRO in the sprayer or spray lines overnight. Flush the sprayer and hose thoroughly each day and upon completion with warm water and dish detergent.

Removal & Clean Up

Once Smart Strip PRO is ready to be removed use a pressure washer or scraper (preferably plastic).

After all paste has been removed, immediately use a nylon brush and clean water to scrub residue off the substrate, paying attention to crevices, grooves and cracks. Rinse thoroughly with water to remove all remaining residue.

For optimal results, low pressure washing is recommended for final rinse when working outside.

Dispose of paper, paste remover and dissolved coatings according to federal, state and local regulations. If you are having difficulty removing the residue after stripping use the Peel Away After Strip and a nylon scrub brush to remove.

Best Practices:

• Always test each type of surface and paint coating for suitability, dwell times, and thickness
• Let Smart Strip PRO dwell at least 6 hours before attempting to remove
• Never apply Smart Strip PRO and leave it for 24 hours without checking on it
• If product dries or hardens to surface, apply a thin coat of Smart Strip PRO over hardened area and wait 30 minutes to 1 hour and remove

WARNING

If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.