Follow us on:

HMG Pre Cat AV Clear Lacquer

HMG Pre Cat AV Clear Lacquer

TOPAVCLE
HMG4389

HMG Pre Cat AV Clear Lacquer is a fast drying 1K lacquer with good film build and excellent application characteristics.

  • Formulated for use on wood substrates
  • For interior use only
  • Available in a range of clear sheen finishes
Colour
Size
Finish
£243.12(incl. VAT)
£202.60(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG Pre Cat AV Clear Lacquer is a fast drying 1K lacquer with good film build and excellent application characteristics.



Click To Jump To Section:




Features & Benefits


  • Formulated for use on wood substrates
  • For interior use only
  • Available in a range of clear sheen finishes



Product Specification


Technical Data
Volume Solids: 28.5%
VOC Content: 0.7kgs/ltr
SG: -
Viscosity: -
Density: 0.94 g/cm³
Storage Conditions: Store between 5°C - 25°C.  When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Flash Point: -4°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Compliant Spray Gun: 25 μm 70g/m² μm
Pressure Pot: 25 μm 70g/m² μm



Coverage: 10 square metres per litre @ 25 microns dft (Theoretical).

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 10 minutes
Dry To Recoat: 10 minutes minimum, 6 hours maximum
Fully Cured: 60 minutes



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.



Application Methods


Technical Data
Compliant Spray Gun Pressure Pot
Mixing Ratio: Ready for use Ready for use
- -
Thinner Options: n/a n/a
- -
Viscosity: 30 - 35 seconds B4 cup 30 - 35 seconds B4 cup
Spray Gun Setup: 1.4 - 1.6 1.2 - 1.4
Number Of Coats (Guide Only): 2 - 3 coats 2 - 3 coats
Flash Off: 10 minutes between coats 10 minutes between coats



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information on basic physical and chemical properties
Form: Liquid
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value: Not determined
Change in Condition
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 76.8°C
Flash Point: - 4°C
Flammability (solid, gas): Not applicable
Ignition temperature: 315°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 1.2 Vol %
Explosion limits: Upper: 12 Vol %
Vapour pressure at 20°C: 100 hPa
Density at 20°C: 0.94 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: Not determined
Viscosity: Kinematic: 24 s (DIN 53211/4)
Solvent content: Organic solvents: 74.8%
Solids content: 28.5%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.

Click to go back to the top of the page

Product Details
4389-645658

Data sheet

Manufacturer
HMG Paints Limited
Interior / Exterior Use
Interior Use
Water / Solvent Based
Solvent
For Use On
Prepared, Unprepared
Application Method
Pressure Pot, Spray
Sheen
Satin, Matt
Colour
Clear
Single, Two or Three Pack
Single
Pack Size
20L
Mixing Ratio
RFU
Suitable Substrates
Wood
Touch Dry (at 20°C)
10 Mins
Dry to Recoat (at 20°C)
10 mins minimum, 6 hours maximum
Fully Cured (at 20°C)
60 Mins
Density
0.94 g/cm³
Solids by Volume
28.5 %
VOC
0.7kgs/ltr
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers.
Recommended Dry Film Thickness
25 μm
Recommended Wet Film Thickness
70g/m² μm
UN Number
UN1263
Base Type
Solvent-Based
Suitable For Use On
Wood
Finish
Matt
Finish
Satin
Application Method
Spray
Product Usage Type
Topcoat
Product Range
Pre Cat
Colour Family
Clear
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG Pre Cat AV Clear Lacquer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like