- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Acrythane ACE is a high performance 2K acrylic polyurethane finish designed to meet the exacting requirements of the agricultural & construction equipment markets.
This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:
2-Pack System Details | |||||
---|---|---|---|---|---|
Base (Part 1) | HMG Acrythane ACE | ||||
Hardener (Part 2) | HMG Hardener 9014 |
- Part one of a two-pack system
- Acrythane ACE is suitable for airless application
- Available in 3,500 colours from RAL, NCS, and British Standard
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartHMG Acrythane ACE is a high performance 2K acrylic polyurethane finish designed to meet the exacting requirements of the agricultural & construction equipment markets.
Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Hardener 9014.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Acrythane ACE is suitable for airless application
- Available in 3,500 colours from RAL, NCS, and British Standard
Recommended for use in with the following HMG primer/filler/sealer systems:
Product Specification
Technical Data | ||||
---|---|---|---|---|
Volume Solids: | 61.7% | |||
VOC Content: | 0.42kgs/ltr | |||
SG: | - | |||
Viscosity: | 360 mPas | |||
Density: | 1.159 g/cm³ | |||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||
Shelf Life: | 12 months from delivery date in original sealed containers. | |||
Pot Life: | 4 Hours @ 20°C | |||
Flash Point: | 24°C |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Airless/Air-Assisted: | 25 - 50 μm | 60 - 125 μm | |
HVLP: | - | - |
Coverage: 19.5 square metres per litre @ 25 microns dft (theoretical)
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
Drying Times At 20°C | |
---|---|
Touch Dry: | 1 hour |
Dry To Handle: | 8 hours |
Fully Cured: | 7 days |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
- Read and follow the safety data sheet, product data sheet and label instructions.
- Stir all paints thoroughly before use.
- Always use the same batch number on the same job.
- Check colour & sheen.
- Filter the product immediately before use.
- Reduce emissions and maintain quality by replacing tin lid after use.
Application Methods
Technical Data | |||||
---|---|---|---|---|---|
Airless/Air-Assisted | HVLP | ||||
Mixing Ratio: | Base: 2 | Base: 2 | |||
Hardener: 1 | Hardener: 1 | ||||
Hardener Options: | Hardener 9014 | Hardener 9014 | |||
Thinner Options: | Thinner 2604 | Thinner 2604 | |||
Viscosity: | Ready for use | 21 - 28 seconds B4 cup | |||
Spray Gun Setup: | 11 - 13 thou 40/50° | 1.2 - 1.6 tip | |||
Number Of Coats (Guide Only): | 1 - 2 full coats | 1 - 2 coats | |||
Flash Off: | 15 minutes between coats | 15 minutes between coats |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Product Notes
Information On Basic Physical And Chemical Properties | ||||
---|---|---|---|---|
Form: | Liquid | |||
Colour: | According to product specification | |||
Odour: | Characteristic | |||
Odour Threshold: | Not determined | |||
pH-value 20°C: | Not determined | |||
Change in Condition | ||||
Melting point/freezing point: | Undetermined | |||
Initial boiling point and boiling range: | 126°C | |||
Flash Point: | 24°C | |||
Flammability (solid, gas): | Not applicable | |||
Ignition temperature: | 315°C | |||
Decomposition temperature: | Not determined. | |||
Auto-ignition temperature: | Product is not selfigniting | |||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||
Explosion limits: Lower: | 1.2 Vol % | |||
Explosion limits: Upper: | 10.8 Vol % | |||
Vapour pressure at 20°C: | 11.2 hPa | |||
Density at 20°C: | 1.159 g/cm³ | |||
Relative density: | Not determined | |||
Vapour density: | Not determined | |||
Evaporation rate: | Not determined | |||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||
Partition coefficient: n-octanol/water: | Not determined | |||
Viscosity: Dynamic at 20°C: | 360 mPas | |||
Viscosity: Kinematic: | Not determined | |||
Solvent content: Organic solvents: | 38.2% | |||
Solids content: | 61.7% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
- Ready for use product contains isocyanates. Suitable air fed respiratory equipment should be worn when spraying.
Data sheet
- Manufacturer
- HMG Paints Limited
- Water / Solvent Based
- Solvent
- For Use On
- Metal
- Application Method
- Spray
- Sheen
- Gloss
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5L
- Mixing Ratio
- Base: 2 - Hardener: 1
- Touch Dry (at 20°C)
- 1 Hour
- Dry to Handle (at 20°C)
- 8 Hours
- Fully Cured (at 20°C)
- 7 Days
- Pot Life (at 20°C)
- 2 Hours
- Coverage
- 19.5 square metres per litre @ 25 microns dft (Theoretical)
- Recommended Thinner/Cleaner
- Thinner 2604
- Density
- 1.159 g/cm³
- Solids by Volume
- 61.7 %
- VOC
- 0.42 Kg/l
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers
- Finish
- Matt
- Size
- 5L
- Recommended Dry Film Thickness
- 25 - 50 μm
- Recommended Wet Film Thickness
- 60 - 125 μm
- UN Number
- UN1263
- Base Type
- Polyurethane
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal
- Finish
- Matt
- Finish
- Gloss
- Application Method
- Spray
- Product Usage Type
- Topcoat
- Product Range
- Acrythane
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Metallic
- Colour Family
- Stone
- Colour Family
- Anthracite Grey
- Colour Family
- Beige
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Acrythane ACE is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Epiprime
HMG Epiprime is a zinc phosphate 2K epoxy primer offering excellent adhesion. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener: 2-Pack System Details Base (Part 1) HMG Epiprime Activator (Part 2) Option 1: HMG Hardener 9058 Standard Option 2: HMG Hardener...
HMG Epoxy Primer EP2 2K
HMG Epoxy Primer EP2 is a zinc phosphate 2K epoxy primer offering excellent adhesion. Supplied as a 4L two-pack product comprising 3L Base and 1L Hardener. Water and chemical resistant. Medium solids 2K epoxy primer. Good corrosion protection. Suitable for commercial transport, bus, coach and rail applications. Designed to be...
HMG Thinner 2604
HMG Thinner 2604 is a slow thinner. For use with compatible HMG systems.
HMG Hardener 9014
HMG Hardener 9014 is an isocyanate hardener. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener: 2-Pack System Details Base (Part 1) HMG Acrythane ACE Hardener (Part 2) HMG Hardener 9014 Part one of a two-pack system
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...