- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Aquaguard 2 is a high quality water based 2K epoxy system.
This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:
| 2-Pack System Details | |||||
|---|---|---|---|---|---|
| Base (Part 1) | HMG Aquaguard 2 | ||||
| Activator (Part 2) | HMG Hardener 9110 | ||||
- Part one of a two part pack
- Good long term durability
- Good chemical resistance
Description
HMG Aquaguard 2 is a high quality Water Based 2K epoxy system.
Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Hardener 9110.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Good long term durability
- Good chemical resistance
Product Specification
| Technical Data | ||||
|---|---|---|---|---|
| Volume Solids: | 72.4% | |||
| VOC Content: | 0.006 base onlyKg/L | |||
| SG: | - | |||
| Viscosity: | 8460 mPas | |||
| Density: | 1.639 g/cm³ | |||
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||
| Shelf Life: | 6 months from delivery date in original sealed containers. | |||
| Pot Life: | 1.5 hours at 20°C. Possible problems after this time. | |||
| Flash Point: | n/a | |||
- Pot Life - No discernable increase in viscocity. If pot life exceeded, adhesion failures will occur.
Film Thickness Range And Coverage
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Compliant Spry Gun: | 35 - 50 μm | 88 - 125 μm | |
| HVLP: | 35 - 50 μm | 88 - 125 μm | |
| Roller: | 35 - 50 μm | 88 - 125 μm | |
| Brush: | 35 - 50 μm | 88 - 125 μm | |
Coverage: 8 square metres per litre @ 40 microns dft.
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
| Drying Times At 20°C | |
|---|---|
| Touch Dry: | 3 hours |
| Dry To Handle: | 24 hours |
| Dry To Recoat: | 1.5 hours at 20°C. Possible problems after this time. |
| Fully Cured: | 5 days |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
- Read and follow the safety data sheet, product data sheet and label instructions.
- Stir all paints thoroughly before use.
- Always use the same batch number on the same job.
- Check colour & sheen.
- Filter the product immediately before use.
- Reduce emissions and maintain quality by replacing tin lid after use.
Application Methods
| Technical Data | |||||
|---|---|---|---|---|---|
| Compliant Spray Gun | HVLP | Roller | Brush | ||
| Mixing Ratio: | Base: 1 | Base: 1 | Base: 1 | Base: 1 | |
| Hardener: 2 | Hardener: 2 | Hardener: 2 | Hardener: 2 | ||
| Thinner: Up to 10% | Thinner: Up to 10% | Thinner: Up to 10% | Thinner: Up to 10% | ||
| Hardener Options: | Hardener 9110 | Hardener 9110 | Hardener 9110 | Hardener 9110 | |
| Thinner Options: | Water | Water | Water | Water | |
| Viscosity: | 70 - 80 seconds B4 cup Ready for use | 70 - 80 seconds B4 cup Ready for use | - | - | |
| Spray Gun Setup: | 1.6 - 1.8 | 1.6 - 1.8 | - | - | |
| Number Of Coats (Guide Only): | 1 - 2 full coats | 1 - 2 full coats | 1 - 2 full coats | 1 - 2 full coats | |
| Flash Off: | - | - | - | - | |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Product Notes
| Information On Basic Physical And Chemical Properties | ||||
|---|---|---|---|---|
| Form: | Liquid | |||
| Colour: | White | |||
| Odour: | Characteristic | |||
| Odour Threshold: | Not determined | |||
| pH-value 20°C: | Not determined | |||
| Change in Condition | ||||
| Melting point/freezing point: | 0°C | |||
| Initial boiling point and boiling range: | 100°C | |||
| Flash Point: | Not applicable | |||
| Flammability (solid, gas): | Not applicable | |||
| Ignition temperature: | Product is not selfigniting. | |||
| Decomposition temperature: | Not determined. | |||
| Auto-ignition temperature: | Product is not selfigniting | |||
| Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||
| Explosion limits: Lower: | Not determined | |||
| Explosion limits: Upper: | Not determined | |||
| Vapour pressure at 20°C: | 23 hPa | |||
| Bulk Density at 20°C: | 1 kg/m³ | |||
| Density at 20°C: | 1.639 g/cm³ | |||
| Relative density: | Not determined | |||
| Vapour density: | Not determined | |||
| Evaporation rate: | Not determined | |||
| Solubility in / Miscibility with water: | NOT MISCIBLE | |||
| Partition coefficient: n-octanol/water: | Not determined | |||
| Viscosity: Dynamic at 20°C: | 180 mPas | |||
| Viscosity: Kinematic: | Not determined | |||
| Solvent content: Organic solvents: | 0.1% - Water: 23.7% | |||
| Solids content: | 72.4% | |||
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
- Suitable respiratory equipment should be worn when spraying.
Product Details
4411-670889
Data sheet
- Manufacturer
- HMG Paints Limited
- For Use On
- Metal
- Application Method
- Brush, Roller, Spray
- Sheen
- Gloss
- Colour
- Standard / Ready Mixed
- VOC Levels
- Ultra-Low (5-49 g/l)
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 7.5L
- Base Type
- Water based
- Mixing Ratio
- Base: 1 - Hardener: 2 - Thinner: Up to 10%
- Touch Dry (at 20°C)
- 3 hours
- Dry to Handle (at 20°C)
- 24 Hours
- Dry to Recoat (at 20°C)
- 1.5hrs @ 20°C possible problems after this time.
- Fully Cured (at 20°C)
- 5 Days
- Pot Life (at 20°C)
- 1.5hrs @ 20°C possible problems after this time.
- Coverage
- 8 square metres per litre @ 40 microns dft
- Recommended Thinner/Cleaner
- Water
- Density
- 1.639 g/cm³
- Solids by Volume
- 72.4 %
- Heat Resistance (up-to)
- 80 °C
- VOC
- 0.006 base only Kg/l
- Shelf Life (from date of manufacture)
- 6 months from delivery date in original sealed containers
- Recommended Dry Film Thickness
- 35 - 50 μm
- Recommended Wet Film Thickness
- 88 - 125 μm
- UN Number
- Not regulated
- Base Type
- Water-Based
- Suitable For Use On
- Metal
- Suitable For Use On
- Primed Surfaces
- Finish
- Gloss
- Application Method
- Brush
- Application Method
- Roller
- Application Method
- Spray
- Usages
- Chemical Resistance
- Usages
- Atmospheric
- Usages
- Tough/Durable
- Product Usage Type
- Topcoat
- Colour Family
- White
- Product Type
- Acrylic
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 3 hours
- Product Attributes
- High Solids
- Product Attributes
- Tough / Durable
- Resistance to
- Chemicals
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Aquaguard 2 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
You might also like
HMG Hardener 9100
HMG Hardener 9100 is a high solids 2K water based isocyanate hardener for use with HMG Hydrothane. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener: 2-Pack System Details Base (Part 1) HMG Hydrothane Activator (Part 2) HMG Hardener 9100 Part two of a...
In stock
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Price
£26.45
(incl. VAT)
In Stock and Available for Delivery