Follow us on:

HMG Acrythane Ultra Colours
HMG Acrythane Ultra Colours

HMG Acrythane Ultra Colours

Acrythane Ultra Colours
HMG4422

HMG Acrythane Ultra Colours is a high solids acrylic polyurethane coating to meet the stringent requirements of the commercial vehicle market.

This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:

2-Pack System Details
Base (Part 1) HMG Acrythane Ultra Colours
Hardener (Part 2) HMG Hardener 9047

  • Part one of a two part system
  • Ease of use
  • High gloss
  • Available in 5,000+ colours from RAL, NCS, and British Standard

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£154.72(incl. VAT)
£128.93(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG Hydrothane 2018 is a high solids acrylic polyurethane coating to meet the stringent requirements of the commercial vehicle market.

Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Hardener 9047.



Click To Jump To Section:




Features & Benefits


  • Part one of a two part system
  • Ease of use
  • High gloss
  • Available in 5,000+ colours from RAL, NCS, and British Standard



Product Specification


Technical Data
HMG Acrythane Ultra Colours
Volume Solids: 61.5%
VOC Content: 0.420kgs/ltr
SG: -
Viscosity: 200 mPas
Density: 1.052 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Pot Life: Maximum 5 seconds increase after 1 hour.
Flash Point: 25°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Gravity Gun: 50 μm 110 μm
Suction Feed: 50 μm 110 μm
Pressure Pot: 50 μm 110 μm



Coverage: 12 - 14 square metres per litre @ 80 microns wft (Theoretical).

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 30 minutes
Dry To Handle: 1 hour
Dry To Recoat: After hard dry (8 hours @ 20°C) denib with p500g dry. After baking allow to cool before flatting and recoating.
Fully Cured: 8 hours



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Read and follow the Safety Data Sheet, Product Data Sheet and label instructions.
  • Stir all paints thoroughly before use.
  • Always use the same batch number on the same job.
  • Check colour & sheen.
  • Filter the product immediately before use.
  • Reduce emissions and maintain quality by replacing tin lid after use.



Application Methods


Technical Data
Gravity Gun Suction Feed Pressure Pot
Mixing Ratio: Base: 3 Base: 3 Base: 3
Hardener: 1 Hardener: 1 Hardener: 1
Thinner: 1 Thinner: 1 Thinner: 1
Hardener Options: Hardener 9047 Hardener 9047 Hardener 9047
Thinner Options: Thinner 2423 below 10°C Thinner 2423 below 10°C Thinner 2423 below 10°C
Thinner 2424 Thinner 2424 Thinner 2424
Thinner 2425 above 25°C Thinner 2425 above 25°C Thinner 2425 above 25°C
Viscosity: 28 - 32 seconds B4 cup 28 - 32 seconds B4 cup 28 - 32 seconds B4 cup
Spray Gun Setup: 1.3 - 1.5 1.6 - 1.8 0.85 - 1.2
Number Of Coats (Guide Only): 2 coats 2 coats 2 coats
Flash Off: Minimum 10 minutes Minimum 10 minutes Minimum 10 minutes



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information On Basic Physical And Chemical Properties
HMG Hydrothane 2018
Form: According to product specification.
Colour: According to product specification.
Odour: Characteristic.
Odour Threshold: Not determined.
pH-value 20°C: Not determined.
Melting point/freezing point: Undetermined.
Initial boiling point and boiling range: 100°C
Flash Point: 25°C
Flammability (solid, gas): Not applicable.
Ignition temperature: 378°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting.
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 1.2 Vol %
Explosion limits: Upper: 7.5 Vol %
Vapour pressure at 20°C: 11.2 hPa
Density at 20°C: 1.052 g/cm³
Relative density: Not determined.
Vapour density: Not determined.
Evaporation rate: Not determined.
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined.
Viscosity: Dynamic at 20°C: 200 mPas
Viscosity: Kinematic: Not determined.
Solvent content: Organic solvents: 38.2%
Solids content: 61.5%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Suitable respiratory equipment should be worn when spraying.

Click to go back to the top of the page

Product Details
4422-847688

Data sheet

Manufacturer
HMG Paints Limited
Water / Solvent Based
Solvent
For Use On
Metal
Application Method
Spray
Sheen
Gloss
Colour
Fully Tintable
Single, Two or Three Pack
Two-Pack
Pack Size
5L
Mixing Ratio
Base: 3 - Hardener: 1 - Thinner: 1
Key Features
Ease of use. High Gloss.
Touch Dry (at 20°C)
30 Mins
Dry to Handle (at 20°C)
1 Hour
Dry to Recoat (at 20°C)
After hard dry (8hrs @ 20°C) denib with p500g dry. After baking allow to cool before flatting and recoating.
Fully Cured (at 20°C)
8 Hours
Pot Life (at 20°C)
Maximum 5 seconds increase after 1 hour.
Coverage
12 - 14 square metres per litre @ 80 microns wft
Recommended Thinner/Cleaner
Thinner 2423 below 10°C - Thinner 2424 - Thinner 2425 above 25°C
Density
1.052 g/cm³
Solids by Volume
61.5 %
VOC
0.420 Kg/l
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers
Recommended Dry Film Thickness
50 μm
Recommended Wet Film Thickness
110 μm
UN Number
UN1263
Base Type
Solvent-Based
Suitable For Use On
Metal
Finish
Gloss
Application Method
Spray
Product Usage Type
Topcoat
Product Range
Acrythane
Colour Family
Red
Colour Family
Brown
Colour Family
Pink
Colour Family
Orange
Colour Family
Purple
Colour Family
Yellow
Colour Family
Black
Colour Family
White
Colour Family
Neutral
Colour Family
Metallic
Colour Family
Stone
Colour Family
Anthracite Grey
Colour Family
Beige
Colour Family
Grey
Colour Family
Green
Colour Family
Blue
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG Acrythane Ultra Colours is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
HMG Thinner 2424

HMG Thinner 2424

We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. HMG Thinner 2424 is a thinner recommended for use in certain HMG systems. Designed for use with Acrythane 4G products.

Shop now
Trustpilot
In stock
HMG Hardener 9047 | Hardeners & Activators

HMG Hardener 9047

HMG Hardener 9047 is a hardener for use with recommeded HMG systems. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener: 2-Pack System Details Base (Part 1) HMG Acrythane 4G Clearcoat HMG Acrythane 4G Colours Hardener (Part 2) HMG Hardener 9047...

Price £145.87 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery