Follow us on:

HMG Synthetic LP Primer

HMG Synthetic LP Primer

PRILP
HMG4428

HMG Synthetic LP Primer is a high build, anti-corrosive, 1K alkyd primer for use under all HMG synthetic topcoats.

  • It combines high build and after a suitable drying period exhibits excellent application and scratch filling properties.
Colour
Size
Finish
£74.68(incl. VAT)
£62.23(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG Synthetic LP Primer is a high build, anti-corrosive, 1K alkyd primer for use under all HMG synthetic topcoats.



Click To Jump To Section:




Features & Benefits


  • It combines high build and after a suitable drying period exhibits excellent application and scratch filling properties.



Product Specification


Technical Data
HMG Synthetic LP Primer
Volume Solids: 65.7%
VOC Content: 0.480kgs/ltr
SG: -
Viscosity: 320 mPas
Density: 1.245 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Pot Life: -
Flash Point: 38°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Airless/Air-Assisted: 30 - 50 μm 60 - 100 μm
Compliant Spray Gun: 30 - 50 μm 60 - 100 μm



Coverage: 16.6 square metres per litre @ 55 microns dft

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Dry To Recoat: Before 16 hours or after 48 hours dependant on film build and conditions.
Fully Cured: 12 hours



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Read and follow the Safety Data Sheet, Product Data Sheet and label instructions.
  • Stir all paints thoroughly before use.
  • Always use the same batch number on the same job.
  • Check colour & sheen.
  • Filter the product immediately before use.
  • Reduce emissions and maintain quality by replacing tin lid after use.



Application Methods


Technical Data
Brush Roller
Mixing Ratio: Base: 95 Base: 95
Thinner: 5 if required Thinner: 5 if required
Thinner Options: Thinner 2621 Thinner 2612
Viscosity: - -
Spray Gun Setup: - -
Number Of Coats (Guide Only): 1 - 2 coats dependant on system 1 - 2 coats dependant on system
Flash Off: - -



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information On Basic Physical And Chemical Properties
QAD HB48 Black Primer
Form: According to product specification
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value 20°C: Not determined
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 139°C
Flash Point: 38°C
Flammability (solid, gas): Not applicable
Ignition temperature: 200°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting.
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 0.6 Vol %
Explosion limits: Upper: 7 Vol %
Vapour pressure at 20°C: 2 hPa
Density at 20°C: 1.245 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 320 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 33.8%
Solids content: 65.7%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Suitable respiratory equipment should be worn when spraying.

Click to go back to the top of the page

Product Details
4428-685821

Data sheet

Manufacturer
HMG Paints Limited
Water / Solvent Based
Water
For Use On
Metal
Application Method
Brush, roller
Sheen
Matt
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
5L
Base Type
Alkyd based
Mixing Ratio
Base: 95 - Thinner: 5 if required
Dry to Recoat (at 20°C)
Before 16 hours or after 48 hours dependant on film build and conditions.
Fully Cured (at 20°C)
12 hours
Recommended Thinner/Cleaner
Thinner 2621
Density
1.245 g/cm³
Solids by Volume
65.7 %
VOC
0.480kgs/ltr
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers.
Recommended Dry Film Thickness
30 - 50 μm
Recommended Wet Film Thickness
60 - 100 μm
UN Number
UN1263
Base Type
Alkyd based
Finish
Matt
Application Method
Brush
Application Method
Roller
Product Usage Type
Undercoat
Colour Family
Grey
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG Synthetic LP Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like
HMG Thinner 2621 | Solvent & Thinner

HMG Thinner 2621

HMG Thinner 2621 is a thinner for use in various applications. For use with compatible HMG systems.

Price £13.45 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery
Hand & Power Tool Surface Preparation Kits for Steel

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.93 (incl. VAT)
Shop now
Trustpilot
In Stock and Available for Delivery