- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG Cellulose Spray Putty (Base) is a spray on, high build cellulose primer/filler/putty for industrial applications.
This product MUST be purchased/used in conjuction with its manufacturer specified base or thinner:
2-Pack System Details | |||||
---|---|---|---|---|---|
Base (Part 1) | HMG Cellulose Spray Putty | ||||
Thinner (Part 2) | Option 1: HMG Thinner 2641 | ||||
Option 2: HMG Thinner 2642 |
- Part one of a two-pack system
- It has many uses including the replacement of undercoat for a super smooth finish
- It is ideal for use over deep scratches and scuff marks
- High build
HMG Cellulose Spray Putty is a spray on, high build cellulose primer/filler/putty for industrial applications.
Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Thinner 2641 or HMG Thinner 2642.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- It has many uses including the replacement of undercoat for a super smooth finish
- It is ideal for use over deep scratches and scuff marks
- High build
Product Specification
Technical Data | ||||||
---|---|---|---|---|---|---|
Cellulose Spray Putty | ||||||
Volume Solids: | 57.1% | |||||
VOC Content: | 0.535 Kg/l | |||||
SG: | - | |||||
Viscosity: | 4000 mPas | |||||
Density: | 1.28 g/cm³ | |||||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||||
Shelf Life: | 12 months from delivery date in original sealed containers. | |||||
Pot Life: | - | |||||
Flash Point: | 13°C |
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Cmpliant Spray Gun: | 65 μm | 150 μm |
Coverage: -
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
Drying Times At 20°C | |
---|---|
Touch Dry: | 7 minutes |
Dry To Recoat: | 15 minutes |
Fully Cured: | 30 minutes |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
- Read and follow the Safety Data Sheet, Product Data Sheet and label instructions.
- Stir all paints thoroughly before use.
- Always use the same batch number on the same job.
- Check colour & sheen.
- Filter the product immediately before use.
- Reduce emissions and maintain quality by replacing tin lid after use.
Application Methods
Technical Data | |||||
---|---|---|---|---|---|
Compliant Spray Gun | |||||
Mixing Ratio: | Base: 1 part | ||||
Thinner: 1 part | |||||
Thinner Options: | Thinner 2641 | ||||
Thinner 2642 | |||||
Viscosity: | - | ||||
Spray Gun Setup: | - | ||||
Number Of Coats (Guide Only): | 2 - 3 coats | ||||
Flash Off: | 10 minutes |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Product Notes
Information On Basic Physical And Chemical Properties | ||||||
---|---|---|---|---|---|---|
HMG Cellulose Spray Putty | ||||||
Form: | According to product specification | |||||
Colour: | According to product specification | |||||
Odour: | Characteristic | |||||
Odour Threshold: | Not determined | |||||
pH-value 20°C: | Not determined | |||||
Melting point/freezing point: | Undetermined | |||||
Initial boiling point and boiling range: | 82°C | |||||
Flash Point: | 13°C | |||||
Flammability (solid, gas): | Not applicable | |||||
Ignition temperature: | 370°C | |||||
Decomposition temperature: | Not determined. | |||||
Auto-ignition temperature: | Product is not selfigniting. | |||||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||||
Explosion limits: Lower: | 1.1 Vol % | |||||
Explosion limits: Upper: | 10.4 Vol % | |||||
Vapour pressure at 20°C: | 10.7 hPa | |||||
Density at 20°C: | 1.28 g/cm³ | |||||
Relative density: | Not determined | |||||
Vapour density: | Not determined | |||||
Evaporation rate: | Not determined | |||||
Solubility in / Miscibility with water: | NOT MISCIBLE | |||||
Partition coefficient: n-octanol/water: | Not determined | |||||
Viscosity: Dynamic at 20°C: | 4000 mPas | |||||
Viscosity: Kinematic: | Not determined | |||||
Solvent content: Organic solvents: | 44.5% | |||||
Solids content: | 57.1% |
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
- Suitable respiratory equipment should be worn when spraying.
Data sheet
- Manufacturer
- HMG Paints Limited
- Water / Solvent Based
- Solvent
- For Use On
- Metal
- Application Method
- Spray
- Sheen
- Matt
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Pack Size
- 5L
- Mixing Ratio
- Base: 1 part - Thinner: 1 part
- Touch Dry (at 20°C)
- 7 Mins
- Dry to Recoat (at 20°C)
- 15 Mins
- Fully Cured (at 20°C)
- 30 Mins
- Recommended Thinner/Cleaner
- Thinner 2641/2641
- Density
- 1.28 g/cm³
- Solids by Volume
- 57.1 %
- VOC
- 0.535 Kg/l
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers
- Recommended Dry Film Thickness
- 65 μm
- Recommended Wet Film Thickness
- 150 μm
- UN Number
- UN1263
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal
- Finish
- Matt
- Application Method
- Spray
- Product Usage Type
- Primer
- Colour Family
- Yellow
Questions
Question about the product
Fraser Walker on 2024-02-14 17:01:38 | Question:
Can this product be used on fiberglass as a primer filler prior to top coat of celulose gloss. I am restoring a Lotus and have had to sand the old paint finish off with a da and 80 grit production paper so the surface has deep scratches. Thanks. Fraser Walker. |
Answer from Rawlins’ Technical Team:
HMG Polykote HS Rapidbuild 2K Primer would be a more suitable product. You might need to apply several coats with recommended flash off times of 10 – 15 mins between coats. | |
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG Cellulose Spray Putty is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2641
HMG Thinner 2641 is a medium fast thinner. Designed for use with cellulose based systems.
HMG Thinner 2642
HMG Thinner 2642 is a medium slow thinner which can be used with compatible HMG systems. For use with cellulose based systems.
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...