Follow us on:

HMG Cellulose Hi Seal Sanding Sealer

HMG Cellulose Hi Seal Sanding Sealer

PRISANSEA
HMG4431

HMG Cellulose Hi Seal Sanding Sealer is a medium solids cellulose based basecoat/sealer for use on wood and veneer.

  • Fast drying
  • Easily sanded
Colour
Size
Finish
£59.68(incl. VAT)
£49.73(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

questions 1 question about the product
Description

HMG Cellulose Hi Seal Sanding Sealer is a medium solids Cellulose based basecoat/sealer for use on wood and veneer.



Click To Jump To Section:




Features & Benefits


  • Fast drying
  • Easily sanded



Product Specification


Technical Data
Cellulose Hi Seal Sanding Sealer
Volume Solids: 31.5%
VOC Content: 0.700kgs/ltr
SG: -
Viscosity: -
Density: 0.939 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Pot Life: -
Flash Point: 4°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Cpmpliant Spray Gun: n/a n/a
Pressure Pot: n/a n/a
Airless/Air-Assisted: n/a n/a



Coverage: 5 square metres per litre at 25 microns dft (theoretical)

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 5 - 10 minutes
Dry To Recoat: Possible after 15 - 30 minutes
Fully Cured: 4 hours



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Read and follow the Safety Data Sheet, Product Data Sheet and label instructions.
  • Stir all paints thoroughly before use.
  • Always use the same batch number on the same job.
  • Check colour & sheen.
  • Filter the product immediately before use.
  • Reduce emissions and maintain quality by replacing tin lid after use.



Application Methods


Technical Data
Compliant Spray Gun Pressure Pot Airless/Air-Assisted
Mixing Ratio: Ready for use Ready for use Ready for use
- - -
Thinner Options: - - -
Viscosity: Ready for use Ready for use Ready for use
Spray Gun Setup: - - -
Number Of Coats (Guide Only): 2 - 3 coats 2 - 3 coats 2 - 3 coats
Flash Off: 1 - 2 full coats 1 - 2 full coats 1 full coat



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information On Basic Physical And Chemical Properties
Cellulose Hi Seal Sanding Sealer
Form: According to product specification
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value 20°C: Not determined
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 82°C
Flash Point: 4°C
Flammability (solid, gas): Not applicable
Ignition temperature: 370°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting.
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 1.2 Vol %
Explosion limits: Upper: 10.4 Vol %
Vapour pressure at 20°C: 29 hPa
Density at 20°C: 0.939 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 4000 mPas
Viscosity: Kinematic: 25 s (DIN 53211/4)
Solvent content: Organic solvents: 72.1%
Solids content: 31.5%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Suitable respiratory equipment should be worn when spraying.

Click to go back to the top of the page

Product Details
4431-685829

Data sheet

Water / Solvent Based
Solvent
For Use On
Prepared
Application Method
Spray, Pressure Pot, Airless Spray, Air-Assisted Spray
Sheen
Matt
Colour
Clear
Single, Two or Three Pack
Single
Pack Size
5L
Suitable Substrates
Wood and Veneer
Touch Dry (at 20°C)
5 - 10 Mins
Dry to Recoat (at 20°C)
Possible after 15 - 30 mins
Fully Cured (at 20°C)
4 Hours
Coverage
5 square metres per litre @ 25 microns dft (Theoretical)
Density
0.939 g/cm³
Solids by Volume
31.5 %
VOC
0.700 Kg/l
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers
UN Number
UN1263
Base Type
Solvent-Based
Base Type
Cellulose
Suitable For Use On
Prepared Surfaces
Finish
Matt
Application Method
Spray
Product Usage Type
Sealer
Colour Family
Clear
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)
questions Nick on 2021-06-11 12:31:36
Question: 

Is this sealer heavy enough to do the job of a grain filler as well? I'd like to use it on open pore woods like mahogany. Thanks

Answer from Rawlins’ Technical Team:

No, unfortunately it is not heavy enough for that type of application.

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG Cellulose Hi Seal Sanding Sealer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT