Follow us on:

HMG Concrete Sealer | Floor Primers & Sealers

HMG Concrete Sealer

PRICONGP
HMG4435

HMG Concrete Sealer is a high performance moisture curing sealer.

  • Offers excellent chemical, solvent, water, petrol, fat and abrasion resistance
  • May be over-coated with a wide variety of HMG high performance topcoats
Colour
Size
Finish
£149.30(incl. VAT)
£124.42(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG Concrete Sealer is a high performance moisture curing sealer.

    • Offers excellent chemical, solvent, water, petrol, fat and abrasion resistance
    • May be over-coated with a wide variety of HMG high performance topcoats



Product Specification


Technical Data
HMG Concrete Sealer
Volume Solids: 56.9%
VOC Content: 0.445 Kg/l
SG: -
Viscosity: 200 mPas
Density: 1.011 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 6 months from delivery date in original sealed containers.
Pot Life: -
Flash Point: 25°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Brush: n/a n/a
Roller: n/a n/a



Coverage: 13 square metres per litre (theoretical).

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Touch Dry: 12 hours
Dry To Recoat: Must be overcoated between 12 - 24 hours
Fully Cured: 24 hours



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Read and follow the safety data sheet, product data sheet and label instructions.
  • Stir all paints thoroughly before use.
  • Always use the same batch number on the same job.
  • Check colour & sheen.
  • Filter the product immediately before use.
  • Reduce emissions and maintain quality by replacing tin lid after use.



Application Methods


Technical Data
Brush Roller
Mixing Ratio: Ready for use Ready for use
- -
Thinner Options: - -
Viscosity: Ready for use Ready for use
Spray Gun Setup: - -
Number Of Coats (Guide Only): 1 - 2 coats 1 - 2 coats
Flash Off: - -



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information On Basic Physical And Chemical Properties
HMG Concrete Sealer
Form: According to product specification
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value 20°C: Not determined
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 137°C
Flash Point: 25°C
Flammability (solid, gas): Not applicable
Ignition temperature: 500%
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting.
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 0.4 Vol %
Explosion limits: Upper: 7.0 Vol %
Vapour pressure at 20°C: 6.7 hPa
Density at 20°C: 1.011 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 200 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 42.9 %
Solids content: 56.9 %



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.

Click to go back to the top of the page

Product Details
4435-687484

Data sheet

Manufacturer
HMG Paints Limited
For Use By
Professional Use
Interior / Exterior Use
Interior Use
For Use On
Concrete
Application Method
Brush, Roller
Sheen
Matt
Colour
Clear
Pack Size
5L
Mixing Ratio
Ready for use
Key Features
Offers excellent chemical, solvent, water, petrol, fat and abrasion resistance
Touch Dry (at 20°C)
12 hours
Dry to Recoat (at 20°C)
Must be overcoated between 12 - 24 hours
Fully Cured (at 20°C)
24 hours
Coverage
13 square metres per litre
Density
1.011 g/cm³
Solids by Volume
56.9%
Shelf Life (from date of manufacture)
6 months from delivery date in original sealed containers.
Size
5L
UN Number
UN1263
Suitable For Use On
Concrete
Finish
Matt
Application Method
Brush
Application Method
Roller
Product Usage Type
Sealer
Colour Family
Clear
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG Concrete Sealer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


COVERAGE CALCULATOR
Units
Total area²
Or enter length and width dimensions:
Length
Width

*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage