Follow us on:

HMG AIF630 Button Polish | Wood & Metal Sealer

HMG AIF630 Button Polish

LACAIF630
HMG4445

HMG AIF630 Button Polish is a pale coloured sealer for use on wood and metal surfaces.  Its fast drying characteristics and ease of application lends itself to a whole variety of usages.

  • The product is a modified resin type and is non-toxic and thus suitable for food contact.
  • Suitable for use using a rubber for French Polishing purposes.
Colour
Size
Finish
£154.63(incl. VAT)
£128.86(ex. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

No queries yet, leave the first!
Description

HMG AIF630 Button Polish is a pale coloured sealer for use on wood and metal surfaces.  Its fast drying characteristics and ease of application lends itself to a whole variety of usages.



Click To Jump To Section:




Features & Benefits


  • The product is a modified resin type and is non-toxic and thus suitable for food contact.
  • Suitable for use using a rubber for French Polishing purposes.



Product Specification


Technical Data
HMG AIF630 Button Polish
Volume Solids: 30.9%
VOC Content: 0.6kgs/ltr
SG: -
Viscosity: 100 mPas
Density: 0.882 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Pot Life: n/a
Flash Point: 13°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Brush: n/a n/a



Coverage: 15 square metres per litre at 25 microns dft (Theoretical)

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Dry To Recoat: After hard dry
Fully Cured: 20 - 30 minutes



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Read and follow the safety data sheet, product data sheet and label instructions.
  • Stir all paints thoroughly before use.
  • Always use the same batch number on the same job.
  • Check colour & sheen.
  • Filter the product immediately before use.
  • Reduce emissions and maintain quality by replacing tin lid after use.



Application Methods


Technical Data
Brush
Mixing Ratio: Ready for use
-
Thinner Options: Thinner 2671
Viscosity: n/a
Spray Gun Setup: n/a
Number Of Coats (Guide Only): 2 - 3 coats
Flash Off: n/a



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information On Basic Physical And Chemical Properties
HMG AIF630 Button Polish
Form: According to product specification
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value 20°C: Not determined
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 78°C
Flash Point: 13°C
Flammability (solid, gas): Not applicable
Ignition temperature: 300°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting.
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 3.5 Vol %
Explosion limits: Upper: 15.0 Vol %
Vapour pressure at 20°C: 59 hPa
Density at 20°C: 0.882 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: 100 mPas
Viscosity: Kinematic: Not determined
Solvent content: Organic solvents: 68.4% - Water 0.7%
Solids content: 30.9%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.

Click to go back to the top of the page

Product Details
4445-690264

Data sheet

Manufacturer
HMG Paints Limited
Water / Solvent Based
Solvent
Application Method
Brush
Sheen
Matt
Colour
Clear
VOC Levels
Low (50-149 g/l)
Single, Two or Three Pack
Single
Product Certifications
Food contact
Pack Size
5L
Mixing Ratio
Ready for use
Suitable Substrates
Wood & metal
Dry to Recoat (at 20°C)
After hard dry
Fully Cured (at 20°C)
20 - 30 minutes
Recommended Thinner/Cleaner
Thinner 2761
Density
0.882 g/cm³
Solids by Volume
30.9%
Heat Resistance (up-to)
50°C
VOC
0.6kgs/ltr
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers.
UN Number
UN1263
Suitable For Use On
Metal
Suitable For Use On
Wood
Finish
Gloss
Application Method
Brush
Product Usage Type
Sealer
Colour Family
Clear
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.

Questions

Question about the product

* Required fields
(read)

Be the first to ask a question about this product!

IMPORTANT SHIPPING & DELIVERY INFORMATION

HMG AIF630 Button Polish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

All delivery costs below are excluding VAT


You might also like