- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG HydroPrime 1K is a water based 1K primer that offers excellent adhesion, build and levelling properties.
- Simple to use and gives fast through hardening
- Good protection against corrosion
- Good coverage, up to 15m2/litre
- Fast drying, in 20-30 minutes
- Available in 5,000+ colours from RAL, NCS, and British Standard
Product customisation
Don't forget to save your customization to be able to add to cartDescription
HMG HydroPrime 1K is a water based 1K primer that offers excellent adhesion, build and levelling properties.
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Product Notes
- Health & Safety
Features & Benefits
- Simple to use and gives fast through hardening
- Good protection against corrosion
- Good coverage, up to 15m2/litre
- Fast drying, in 20-30 minutes
- Available in 5,000+ colours from RAL, NCS, and British Standard
Product Specification
| Technical Data | ||||||
|---|---|---|---|---|---|---|
| HMG HydroPrime 1K | ||||||
| Volume Solids: | 51.2% | |||||
| VOC Content: | 0.08 Kg/l | |||||
| SG: | - | |||||
| Viscosity: | 200 mPas | |||||
| Density: | 1.048 g/cm³ | |||||
| Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | |||||
| Shelf Life: | 12 months from delivery date in original sealed containers. | |||||
| Pot Life | n/a | |||||
| Flash Point | 101°C | |||||
Film Thickness Range And Coverage
| Product Data | |||
|---|---|---|---|
| Dry Film Thickness | Wet Film Thickness | ||
| Compliant Spray Gun: | n/a | n/a | |
| Pressure Pot: | n/a | n/a | |
Coverage: 15.0 square metres per litre @ 25 microns dft (Theoretical).
- HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
- These values are a guide only and are not to be used as specifications.
- Film thickness will vary depending on actual use and specification.
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.
Drying Times
| Drying Times At 20°C | |
|---|---|
| Dry To Recoat: | After hard dry |
| Fully Cured: | 20 - 30 minutes |
Surface Preparation
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
- Read and follow the safety data sheet, product data sheet and label instructions.
- Stir all paints thoroughly before use.
- Always use the same batch number on the same job.
- Check colour & sheen.
- Filter the product immediately before use.
- Reduce emissions and maintain quality by replacing tin lid after use.
Application Methods
| Technical Data | |||||
|---|---|---|---|---|---|
| Compliant Spray Gun | Pressure Pot | ||||
| Mixing Ratio: | Ready for use | Ready for use | |||
| - | - | ||||
| Thinner Options: | n/a | n/a | |||
| Viscosity: | n/a | n/a | |||
| Spray Gun Setup: | 1.6 - 1.8 Fluid Tip | 1.1 Fluid Tip | |||
| Number Of Coats (Guide Only): | 2 coats | 2 coats | |||
| Flash Off: | 10 - 15 between coats | 10 - 15 between coats | |||
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Product Notes
| Information On Basic Physical And Chemical Properties | ||||||
|---|---|---|---|---|---|---|
| HMG HydroPrime 1K | ||||||
| Form: | According to product specification | |||||
| Colour: | According to product specification | |||||
| Odour: | Characteristic | |||||
| Odour Threshold: | Not determined | |||||
| pH-value 20°C: | Not determined | |||||
| Melting point/freezing point: | Undetermined | |||||
| Initial boiling point and boiling range: | 100°C | |||||
| Flash Point: | 101°C | |||||
| Flammability (solid, gas): | Not applicable | |||||
| Ignition temperature: | - | |||||
| Decomposition temperature: | Not determined. | |||||
| Auto-ignition temperature: | Product is not selfigniting. | |||||
| Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | |||||
| Explosion limits: Lower: | Not determined | |||||
| Explosion limits: Upper: | Not determined | |||||
| Vapour pressure at 20°C: | 23 hPa | |||||
| Density at 20°C: | 1.048 g/cm³ | |||||
| Relative density: | Not determined | |||||
| Vapour density: | Not determined | |||||
| Evaporation rate: | Not determined | |||||
| Solubility in / Miscibility with water: | NOT MISCIBLE | |||||
| Partition coefficient: n-octanol/water: | Not determined | |||||
| Viscosity: Dynamic at 20°C: | 200 mPas | |||||
| Viscosity: Kinematic: | Not determined | |||||
| Solvent content: Organic solvents: | 2.9% - Water 53.8% | |||||
| Solids content: | 51.2% | |||||
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use.
- Suitable respiratory equipment should be worn when spraying.
Product Details
4446-889977
Data sheet
- Manufacturer
- HMG Paints Limited
- Water / Solvent Based
- Water
- For Use On
- Metal
- Application Method
- Spray, pressure pot
- Sheen
- Matt
- Colour
- Standard / Ready Mixed
- VOC Levels
- Low (50-149 g/l)
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
- Mixing Ratio
- Ready for use
- Dry to Recoat (at 20°C)
- After hard dry
- Fully Cured (at 20°C)
- 20 - 30 minutes
- Pot Life (at 20°C)
- n/a
- Coverage
- 15.0 square metres per litre @ 25 microns dft
- Density
- 1.048 g/cm³
- VOC
- 0.08 Kg/l
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers
- UN Number
- Not regulated
- Base Type
- Water-Based
- Suitable For Use On
- Metal
- Finish
- Matt
- Finish
- Gloss
- Application Method
- Spray
- Application Method
- Pressure Pot
- Usages
- Atmospheric
- Usages
- Anti-Corrosive
- Product Usage Type
- Primer
- Product Range
- HydroPrime
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Metallic
- Colour Family
- Stone
- Colour Family
- Anthracite Grey
- Colour Family
- Beige
- Dry to Recoat (@ 20-25°C)
- 30 mins
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG HydroPrime 1K is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
You might also like
