- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG SPS70 Primer Finish is a quick drying, durable, anti-corrosive, single protection system providing hard wearing, tough matt, semi-gloss or full gloss finish - Keeps equipment looking new for longer. Application direct to metal with wet-on-wet application.
- For professional use
- Quick-drying - touch dry in 30 mins, hard dry after 6 hours at 20°C
- Coverage: 4-5m² per litre
- 70% gloss sheen
- Ideal for skips, containers or other steel equipment requiring fast turnaround
- Also suitable for aluminium and mild, galvanised or shot-blasted steel
- Resistant to some chemicals, oils and grease
- Spray application
- Available in 5,000+ colours from RAL, NCS, and British Standard
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartDescription
Click To Jump To Section:
- Features & Benefits
- Product Specification
- Substrates
- Application Climate
- Application Information
- Surface Preparation
- Bare substrates
- Previously Painted
- Health & Safety
Features & Benefits
- For professional use
- Coverage: 4-5m²/L
- Drying times at 20°C:
- Touch dry: 30 minutes
- Dry to recoat: 20 minutes
- Fully cured: 6 hours
- Dry film thickness: 40 microns
- Wet film thickness: 100 microns
- Number of coats:
- Airless, air assisted & pressure pot: 1 coat
- Compliant spray: 2 coats
- Flash off: 15 minutes between coats
- Available in 5,000+ colours from RAL, NCS, and British Standard
Substrates
- HMG SPS Primer Finish is suitable as a primer/finish coat for suitably prepared metals, clean and free of grease, oils and other contaminants
- Not suitable for coating over bitumen or chlorinated rubber coatings
Application Climate
- Substrate temperature should be 5⁰C or above for application and during cure, and a minimum of 3⁰C above the dew point
- Adequate dry air ventilation should be supplied during drying
Application Information
- Thinning should only take place after material is thoroughly mixed
- Application and use should always conform with the codes of practice described in BS 6150 and BS 5493
Surface Preparation
- Ensure surfaces are clean, dry and free from grease, oils, dust and other contamination prior to application
- Thoroughly clean and degrease using suitable HMG Prep Clean 2802, HMG 2803 or HMG 2804
- Rust/corrosion to be removed to Sa or St standards, remove to clean metallic appearance with little or no rust/corrosion present
- Areas where blast cleaning is not cost effective or practical, then the use of HMG Ferrozinc is an alternative
- Though Ferrozinc is not an equivalent alternative to shot blasting, it does offer a far superior performance than conventional coatings applied to slightly rusted surfaces
- Read and follow safety data sheet, technical data sheet (see section above) and label instructions
- Stir paint thoroughly before use
- Always use the same batch number on the same job
- Filter the product immediately before use
- Reduce emissions and maintain quality by replacing tin lid after use
Bare substrates
- Mild steel – Remove millscale and thoroughly degrease using suitable HMG Prep Clean. Abrade with P80 – P180 if necessary, prior to application of primer
- Shot Blasted Steel – Remove all traces of blast grit/sand prior to application of primer
- Aluminium – Abrade with P180 – P320, degrease with suitable HMG Prep Clean prior to application of primer
- Galvanised Steel – Degrease with suitable HMG Prep Clean, apply HMG Mordant Wash, apply HMG Etch Primer and if required use appropriate HMG Primer
Previously Painted
- High pressure wash to remove all loose debris and poorly adhered previous coatings to remove all salts and other contaminants
- Degrease using suitable HMG Degreaser 2800 to remove grease and oils not removed with pressure washing alone
- Existing coatings to be well adhered with all edges tight and well feathered. Rust/corrosion to be removed back to clean metallic appearance
- Abrade to provide good adhesion
- Wipe over with degreaser to remove loose debris from abrasion
- Substrate to be clean, free of grease, oils, dust and completely dry prior to application
For further assistance contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use
- Suitable respiratory equipment should be worn when spraying
- Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with Water and disposed of in a non-combustible container with a tight fitting lid
Product Details
4460-1036605
Data sheet
- Manufacturer
- HMG Paints Limited
- For Use By
- Professional Use
- For Use On
- Skips
Metal Containers
Mild Steel
Galvanised Steel
Shot Blasted Steel
Aluminium - Application Method
- Spray
- Sheen
- 70% Sheen
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Pack Size
- 1L
5L
15L - Mixing Ratio
- Compliant Spray Gun: Base: 1 - Thinner: 10 - 20%
- Touch Dry (at 20°C)
- 30 Mins
- Dry to Recoat (at 20°C)
- Minimum 20 minutes
- Fully Cured (at 20°C)
- 6 hours
- Coverage
- 4 - 5m²/L
- Recommended Thinner/Cleaner
- Thinner 2621
- Density
- SPS70 Colours: 0.986 g/cm³ - SPS70 Colours (Contains Lead): 1.048 g/cm³
- Solids by Volume
- SPS70 Colours: 46.6% - SPS70 Colours (Contains Lead): 47.7%
- VOC
- 0.480kgs/ltr
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers.
- Finish
- 70% Sheen
- Recommended Dry Film Thickness
- 40 μm
- Recommended Wet Film Thickness
- 100 μm
- UN Number
- UN1263
- Colour(s)
- Fully Tintable
- Base Type
- Solvent-Based
- Suitable For Use On
- Galvanised Steel
- Suitable For Use On
- Skips
- Suitable For Use On
- Metal Containers
- Suitable For Use On
- Mild Steel
- Suitable For Use On
- Shot Blasted Steel
- Suitable For Use On
- Compatible Existing Coatings
- Suitable For Use On
- Aluminium
- Suitable For Use On
- Steel
- Finish
- Semi-Gloss
- Application Method
- Spray
- Manufacturer
- HMG Paints LTD
- Usages
- Direct to Metal
- Usages
- Chemical Resistance
- Usages
- Metal Protectors
- Usages
- Atmospheric
- Usages
- Anti-Corrosive
- Usages
- Tough/Durable
- Usages
- Primer/Finish
- Usages
- 1 Coat
- Product Usage Type
- Topcoat
- Colour Family
- Beige
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 30 mins
- Product Attributes
- 1 coat
- Product Attributes
- Anti-Corrosive
- Product Attributes
- Primer/Finish
- Product Attributes
- Tough
- Resistance to
- Chemicals
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG SPS70 Primer Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
HMG Mordant T Wash
HMG Mordant T Wash is designed for use as an etching solution for galvanised steel & zintec. Manufactured to a formulation originally developed by the British Rail Board
Price
£45.60
(incl. VAT)
In Stock and Available for Delivery
HMG Chromate Free Etch Primer
HMG Chromate Free Etch Primer is a quick drying chromate free etch primer providing good anti corrosive properties and excellent adhesion to ferrous and non-ferrous metals. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator when used as a wash primer: 2-Pack System Details Base...
Price
£101.32
(incl. VAT)
In Stock and Available for Delivery
HMG SPS70 Primer Finish
HMG SPS70 Primer Finish is a quick drying, durable, anti-corrosive, single protection system providing hard wearing, tough matt, semi-gloss or full gloss finish - Keeps equipment looking new for longer. Application direct to metal with wet-on-wet application. For professional use Quick-drying - touch dry in 30 mins, hard dry after 6...
Price
£22.10
(incl. VAT)
In Stock and Available for Delivery
HMG Prep Clean 2802
HMG Prep Clean 2802 is a fast evaporating, strong Preparatory Cleaning solvent for the heavy duty degreasing of substrates. Used in many applications For use on bare surfaces only
Price
£45.11
(incl. VAT)
In Stock and Available for Delivery
HMG Prep Clean 2804
HMG Prep Clean 2804 is a water based preparatory Cleaner for the degreasing of substrates. Used in many applications For use on bare surfaces only
Price
£39.78
(incl. VAT)
In Stock and Available for Delivery
HMG Prep Clean 2803
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. HMG Prep Clean 2803 is a slow evaporating, low odour and mild preparatory cleaning solvent for the degreasing of substrates. Used in many...
In stock
HMG Prep Clean 2800
HMG Prep Clean 2800 is a fast evaporating, mild preparatory cleaning solvent for the degreasing of substrates. Used in many applications Mildly anti-static For use previously painted surfaces
Price
£45.30
(incl. VAT)
In Stock and Available for Delivery
HMG Thinner 2621
HMG Thinner 2621 is a thinner for use in various applications. For use with compatible HMG systems.
Price
£13.45
(incl. VAT)
In Stock and Available for Delivery
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
Price
£25.93
(incl. VAT)
In Stock and Available for Delivery