- There are no more items in your cart
- Shipping Calculated at checkout
-
Sub-Total (inc. VAT)
£0.00
HMG SPS30 Primer Finish is a quick drying SPS (Single Protection System) single coat finish offering excellent performance.
- Provided with a sheen level of 30% finish
- Hard dry in as little as 60 minutes at 20℃
- Touch dry in 30 mins at 20℃
- Coverage up to 8-10m2 per litre
- Flashpoint: 24℃
- Available in 5,000+ colours from RAL, NCS, and British Standard
- Also available as an aerosol, please see HMG SPS30 Primer Finish Aerosol
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Product customisation
Don't forget to save your customization to be able to add to cartClick To Jump To Section:
- Features & Benefits
- Film Thickness Range And Coverage
- Drying Times
- Surface Preparation
- Application Methods
- Health & Safety
Features & Benefits
- Ready for use (unless using Compliant Spray - thin 10-20% with Thinner 2621)
- One full coat required (Compliant Spray requires two coats)
- Available in 5,000+ colours from RAL, NCS, and British Standard
Film Thickness Range And Coverage
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Airless/Air-Assisted: | 70 μm | 160 μm | |
Pressure Pot: | 55 μm | 120 μm | |
Compliant Spray Gun: | 45 μm | 100 μm |
Coverage: 8-10m2 per litre at 100 microns wft (Theoretical)
- HMG Technical Data Sheet (available in Data Sheet tab above) indicates a dry film thickness that will be achieved when applying a particular wet film thickness
- These values are a guide only and are not to be used as specifications
- Film thickness will vary depending on actual use and specification
- Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness
Drying Times
Drying Times At 20°C | |
---|---|
Touch Dry: | 30 minutes |
Dry To Recoat: | Approximately 48 hours at 20°C dependant on film thickness. |
Fully Cured: | 60 minutes |
Application Methods
- Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants
- Read and follow the Safety Data Sheet (available in Data Sheet tab above) and label instructions
- Stir all paints thoroughly before use
- Always use the same batch number on the same job
- Check colour & sheen
- Filter the product immediately before use
- Reduce emissions and maintain quality by replacing tin lid after use
Application Methods
Technical Data | |||||
---|---|---|---|---|---|
Airless/Air-Assisted | Pressure Pot | Compliant Spray Gun | |||
Mixing Ratio: | Ready for use | Ready for use | - | ||
- | - | Thinner: 10 - 20% | |||
Thinner Options: | - | - | Thinner 2621 | ||
Viscosity: | Ready for use | Ready for use | 50 - 65 seconds B4 cup | ||
Spray Gun Setup: | 13 - 15 thou 40/50° | 2.0 | 1.6 - 2.0 | ||
Number Of Coats (Guide Only): | 1 full coat | 1 full coat | 2 full coats | ||
Flash Off: | 15 minutes between coats |
For further information on mixing ratios please contact Rawlins Paints Technical on - 0113 2455450 (option 2) or [email protected].
Health & Safety
- Refer to the safety data sheet in the attachments section above and tin label prior to use
- Suitable respiratory equipment should be worn when spraying
- Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water and disposed of in a non-combustible container with a tight fitting lid
Data sheet
- Manufacturer
- HMG Paints Limited
- For Use By
- Professional Use
- For Use On
- Metal
- Application Method
- Spray
- Sheen
- 30% Sheen
- Colour
- Fully Tintable
- Single, Two or Three Pack
- Single
- Pack Size
- 5L
15L - Touch Dry (at 20°C)
- 30 Mins
- Dry to Recoat (at 20°C)
- Approximately 48 hours at 20°C dependant on film thickness.
- Fully Cured (at 20°C)
- 60 minutes
- Coverage
- 8-10m²/L @ 100 microns wft
- Recommended Thinner/Cleaner
- HMG 2621
- VOC
- 0.520 Kg/l
- Shelf Life (from date of manufacture)
- 12 months from delivery date in original sealed containers
- Finish
- 30% Sheen
- UN Number
- UN1263
- Colour(s)
- Fully Tintable
- Base Type
- Solvent-Based
- Suitable For Use On
- Metal
- Suitable For Use On
- Steel
- Suitable For Use On
- Compatible Existing Coatings
- Finish
- Eggshell
- Application Method
- Spray
- Manufacturer
- HMG Paints LTD
- Usages
- Chemical Resistance
- Usages
- Quick Drying
- Usages
- Atmospheric
- Usages
- Anti-Corrosive
- Usages
- Tough/Durable
- Usages
- Primer/Finish
- Usages
- 1 Coat
- Usages
- Direct to Metal
- Product Usage Type
- Primer
- Colour Family
- Purple
- Colour Family
- Yellow
- Colour Family
- Black
- Colour Family
- White
- Colour Family
- Neutral
- Colour Family
- Grey
- Colour Family
- Green
- Colour Family
- Blue
- Colour Family
- Red
- Colour Family
- Brown
- Colour Family
- Pink
- Colour Family
- Orange
- Environment
- Atmospheric
- Touch Dry/Dust Free (@ 20-25°C)
- 30 mins
- Product Attributes
- 1 coat
- Product Attributes
- Anti-Corrosive
- Product Attributes
- Primer/Finish
- Product Attributes
- Tough
- Resistance to
- Chemicals
Questions
Question about the product
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
HMG SPS30 Primer Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2621
HMG Thinner 2621 is a thinner for use in various applications. For use with compatible HMG systems.
HMG SPS30 Primer Finish Aerosol
HMG SPS30 Primer Finish Aerosol is a quick drying SPS (Single Protection System) single coat finish offering excellent performance. For the non-aerosol version of this product please see HMG SPS30 Primer Finish. Provided with a sheen level of 30% finish Hard dry in as little as 60 minutes at 20℃ Coverage up to 8-10m2/L 400ml/16oz Aerosol...
Surface Preparation Kits for Steel
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...